summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* cleanup: Standardize use of CONFIG_I2C and add MASTER/SLAVE CONFIGsShawn Nematbakhsh2015-11-0339-15/+55
* oak: handle the warm reset key from servo boardBen Lok2015-11-033-0/+15
* mec1322: fix gpio_disable_interruptKyoung Kim2015-11-031-1/+1
* oak: Adding 2S and 3S battery supportBen Lok2015-11-031-6/+2
* nds32: fix interruptDino Li2015-11-012-0/+22
* it8380dev: fix irq, jtag and systemDino Li2015-11-015-21/+89
* nuc: Add state machines to handle i2c master stall bus and call i2c_xfer again.Mulin Chao2015-11-011-21/+94
* glower: Remove boardShawn Nematbakhsh2015-10-308-319/+0
* glados: oak: chell: enable USB PD loggingAlec Berg2015-10-304-0/+8
* stm32f0: i2c: Set timing register values by port clock sourceShawn Nematbakhsh2015-10-302-30/+57
* cr50: upgrade to the latest FPGA image 20151029_41713@78167Vadim Bendebury2015-10-301-577/+700
* samus: increase POWERBTN task stack sizeAlec Berg2015-10-301-1/+1
* pd: turn on CONFIG_USB_PD_LOW_POWER by defaultAlec Berg2015-10-301-1/+1
* pd: add more power improvements to PD taskAlec Berg2015-10-302-3/+43
* Jerry: enable virtual batteryMary Ruthven2015-10-291-0/+3
* oak: ensure PMIC power button is released after SYSJUMP.Ben Lok2015-10-281-0/+8
* Lars: enable USB-A port power controlRyan Zhang2015-10-282-4/+5
* motion: Remove duplicate shutdown codeGwendal Grignou2015-10-284-16/+8
* driver: si114x: Fail init of proximity sensor if light sensor fails.Gwendal Grignou2015-10-282-1/+4
* driver: bmi160: Add magic sequence to unlockGwendal Grignou2015-10-271-1/+12
* Remove cyan ec configurationBernie Thompson2015-10-2710-789/+0
* charger: Add LIMIT_POWER charger param for low bat + weak chargerShawn Nematbakhsh2015-10-277-3/+74
* i2c: get battery information from charge stateMary Ruthven2015-10-276-4/+90
* chell: Set SPI flash chip to W25X40Duncan Laurie2015-10-271-1/+1
* flash_ec: Add support for flashing chell PDDuncan Laurie2015-10-271-2/+3
* it8380dev: gpio - remove comment about E4Dino Li2015-10-251-2/+0
* it8380dev: Increase DLM sizeDino Li2015-10-253-10/+22
* it8380dev: fix clock moduleDino Li2015-10-2512-37/+399
* glados: oak: reboot EC if PD MCU crashesAlec Berg2015-10-235-21/+34
* pd: remove unnecessary delay in phy initAlec Berg2015-10-231-1/+1
* ryu: fix lid close detectionVincent Palatin2015-10-231-1/+1
* ryu: do not pull EN_PP3300Vincent Palatin2015-10-231-1/+1
* common: lightbar: Add histeresis to prevent flickeringGwendal Grignou2015-10-236-23/+96
* board: ryu: Compass and Gyro stays up in S5Gwendal Grignou2015-10-231-2/+2
* mec1322: Remove CONFIG_PORT80_TASK_EN from boards.Aseda Aboagye2015-10-238-8/+0
* lars: remove port80 taskAlec Berg2015-10-231-2/+1
* glados: chell: add VCONN swap abilityAlec Berg2015-10-234-0/+20
* pd: change battery and variable sink cap for voltage inaccuracyAlec Berg2015-10-2310-20/+18
* pd: send soft reset on boot if VBUS is presentAlec Berg2015-10-234-49/+41
* oak: revise suspend gpio setting for rev4YH Huang2015-10-231-0/+4
* oak: stm32f0: implement i2c_set_timeoutRong Chang2015-10-232-8/+16
* Cr50: Support USB on 15MHz FPGA imageBill Richardson2015-10-222-13/+152
* Lars: Init boardRyan Zhang2015-10-2213-1/+1590
* flash_ec: Use the chip name to check stm32 boardTom Wai-Hong Tam2015-10-221-28/+27
* tcpc: re-initialize tcpc if it reboots while tcpm is runningAlec Berg2015-10-226-28/+96
* Cr50: Support FPGA image m3.dist_20151021_054409Bill Richardson2015-10-229-2514/+2915
* ps8740: Make revision check a minimum instead of explicit valueDuncan Laurie2015-10-211-1/+1
* flash_ec: Add chell and lars boardsDuncan Laurie2015-10-211-0/+2
* Kunimitsu: Add support to enable L3GD20H gyrometerVijay Hiremath2015-10-212-0/+46
* kunimitsu: enable USB-A port power controlKevin K Wong2015-10-212-4/+5