summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
* it8380dev: change PNPCFG base address to 4E/4FDino Li2015-08-041-2/+2
* it8380dev: fix keyboard no break codeDino Li2015-08-041-0/+10
* tcpc: fix rx buffer overrun bugAlec Berg2015-08-041-2/+6
* usb_charger: configure boards to disconnect USB when UFP.Alec Berg2015-08-044-0/+4
* flash_ec: add support for SWD, nrf51, and hadokenMyles Watson2015-08-046-3/+71
* usb_charger: cleanup: move setting usb 2 switches to usb_chargerAlec Berg2015-08-0412-99/+40
* oak: updates GPIO setting for rev3Ben Lok2015-08-042-36/+56
* flash_ec: Set a 10-minute timeout for flashing ECTom Wai-Hong Tam2015-08-041-5/+12
* it8380dev: modify sspi moduleDino Li2015-08-045-29/+42
* npcx: Fix termination of chip revisionRandall Spangler2015-08-041-1/+2
* glados: Add bd99992gw temperature sensorsShawn Nematbakhsh2015-08-032-1/+26
* driver/temp_sensor: Add support for BD99992GWShawn Nematbakhsh2015-08-036-0/+408
* oak: Request different DP pin modes including multi-function.Ben Lok2015-08-031-5/+17
* oak: power: Set 10s for long power key press to force shutdownYH Huang2015-08-031-5/+5
* pd: don't enable try.src when battery is not present or too lowAlec Berg2015-08-023-17/+48
* tcpc: add RX message buffer and don't send goodCRC when fullAlec Berg2015-08-013-39/+101
* cr50: initial tpm state machine supportVadim Bendebury2015-08-011-22/+232
* tasks: Remove most task_start_called() calls.Aseda Aboagye2015-08-016-17/+7
* motion_sense: Move angle calculation under LPC_MODEGwendal Grignou2015-08-012-5/+15
* skylake: Inhibit AP power-on until charge current limit is setShawn Nematbakhsh2015-08-012-0/+25
* oak: power: change power state while losting POWER_GOOD signalYH Huang2015-08-011-16/+76
* glados: Free up program memory spaceShawn Nematbakhsh2015-08-011-0/+4
* mec1322: Fix dedicated SPI port accessShawn Nematbakhsh2015-08-012-2/+8
* glados: Buffer AC status to the PCHDuncan Laurie2015-08-011-0/+12
* ryu: remove SH UART debug and leftoversVincent Palatin2015-08-013-40/+4
* ryu: dynamic switch between SPI and I2C sensors configurationGwendal Grignou2015-08-013-21/+52
* driver: bmi160: Allow Dynamic selection of SPI or I2C transportGwendal Grignou2015-08-012-76/+81
* board: ryu: Enable SPI access to AccelGwendal Grignou2015-08-013-12/+33
* driver: bmi160: Improve FIFO handlingGwendal Grignou2015-08-012-25/+60
* motion_sense: Fix invalid optimizationGwendal Grignou2015-08-011-9/+14
* ryu: Increase CHIPSET stack sizeGwendal Grignou2015-08-011-1/+1
* driver: bmi160: Fix bugs found testing SPIGwendal Grignou2015-08-013-13/+26
* driver: bmi160: Add SPI access supportGwendal Grignou2015-08-013-21/+90
* stm32: spi: Add lock around spi_transactionGwendal Grignou2015-08-011-0/+6
* mec1322: make i2c transactions faster by not sleeping taskAlec Berg2015-08-011-36/+29
* oak: fix default input current limitRong Chang2015-07-311-3/+4
* stm32: Enable 3rd SPI interfaceGwendal Grignou2015-07-308-22/+40
* accel: mechanical changes from i2c_addr to addrGwendal Grignou2015-07-3011-119/+120
* common: change interface to SPI flashGwendal Grignou2015-07-3030-183/+351
* Makefile.rules: Fix build timestamp.Aseda Aboagye2015-07-301-1/+1
* stm32f05: decrease default system stack sizeAlec Berg2015-07-291-0/+4
* Driver: Add macros to conditionally compile the console commandsVijay Hiremath2015-07-2913-5/+38
* glados: implement and enable fast charging profilesAlec Berg2015-07-292-0/+178
* host_command_pd: loop over sending PD status host commandAlec Berg2015-07-292-69/+85
* cyan: Increase chipset stack size.Divagar Mohandass2015-07-281-1/+1
* acpi: Ensure continuity of memmap data with a read cacheShawn Nematbakhsh2015-07-2810-105/+76
* mec1322: keep 32KHz on for ROSC accuracyKyoung Kim2015-07-281-7/+1
* mec1322: Power state transition in case of apshutdownKyoung Kim2015-07-281-0/+21
* pd: enable try.src for necessary boardsAlec Berg2015-07-274-0/+4
* kunimitsu: disable asserts to save flash spaceAlec Berg2015-07-271-1/+2
View Lorry Controller Status