summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
* Lars: Remove second port of PD firmwareRyan Zhang2015-12-065-136/+19
* tcpc: add 2 bytes into TX byte count registerAlec Berg2015-12-052-4/+2
* snoball: Enable PWMs for post-regulator voltage controlShawn Nematbakhsh2015-12-043-8/+32
* honeybuns: Allow 20v chargingScott2015-12-041-3/+1
* stm32: pwm: Allow configuration of pwm frequency + complementary outputsShawn Nematbakhsh2015-12-043-6/+22
* pwm: Add common initialization for PWM pinsShawn Nematbakhsh2015-12-0425-64/+52
* kunimitsu: modify charge LED gpio control to match FAB4 schematicli feng2015-12-032-4/+4
* pd: Fix unwanted resets on single-role power suppliesShawn Nematbakhsh2015-12-031-2/+4
* cr50: add extension command for testing hash primitivesVadim Bendebury2015-12-032-3/+228
* Smart battery: wait for any battery responseMary Ruthven2015-12-031-21/+7
* Fan: Allow fan at max speed during the boot time.Kyoung Kim2015-12-031-2/+8
* cr50: reduce hash implementation stack requirementsVadim Bendebury2015-12-035-16/+31
* Lars: Add ALS supportRyan Zhang2015-12-034-7/+24
* Lars: Refactoring PD port count settingRyan Zhang2015-12-031-23/+7
* nuc: enable CLKRUN functionality for SERIRQ quiet mode.CHLin2015-12-031-0/+6
* cr50: fix cryptography problemsVadim Bendebury2015-12-031-2/+1
* cr50: test: add hash testing host side implementationVadim Bendebury2015-12-032-1/+121
* cr50: test: move crypto test into its own moduleVadim Bendebury2015-12-033-230/+267
* chell: Keep keyboard backlight off in hibernateDuncan Laurie2015-12-012-1/+4
* cr50: test: extended command code does not have to be passed as argumentVadim Bendebury2015-12-011-10/+6
* oak: pd: increase stack size of PDCMD taskBen Lok2015-12-011-1/+1
* Cr50: Clean up the GINTSTS USB macrosBill Richardson2015-12-012-16/+9
* Cr50: Replace magic numbers for GGPIO controlBill Richardson2015-12-012-4/+41
* common: adc/i2c: Mark task_waiting volatileShamile Khan2015-12-017-11/+9
* usb: Put HID descriptor in the correct orderBill Richardson2015-12-011-4/+4
* Lars: update fan settingsRyan Zhang2015-12-012-1/+2
* oak: enable HW charge rampingBen Lok2015-12-012-0/+35
* driver: si114x: Unlock the device if stuckGwendal Grignou2015-12-012-1/+27
* nuc: Add i2cscan and kbpress commands for FAFT.Mulin Chao2015-12-012-41/+31
* motion: Set interrupt interval properly for sensor in force modeGwendal Grignou2015-12-011-6/+22
* device: si114x: Address overflow conditionGwendal Grignou2015-12-012-1/+2
* Cr50: bootloader: display config bits at bootBill Richardson2015-12-011-2/+6
* motion: At shutdown, access sensors only if initialized.Gwendal Grignou2015-12-011-2/+9
* lars_pd: preparing new PD firmware for one-typeC-port PDRyan Zhang2015-12-018-1/+712
* fusb302: Don't flush RX FIFO on GoodCRCShawn Nematbakhsh2015-12-011-4/+7
* pd: send power change event to AP whenever input power is changedBen Lok2015-12-015-0/+26
* mec1322_evb: Remove boardShawn Nematbakhsh2015-11-307-200/+0
* mec1322: i2c: Assume read-no-write transactions are repeated startShawn Nematbakhsh2015-11-301-16/+7
* mec1322: i2c: Add hard-timeout for status waitShawn Nematbakhsh2015-11-301-15/+19
* Lars: update for proto boardRyan Zhang2015-11-303-12/+8
* Lars: update I2C port MACRORyan Zhang2015-11-301-1/+0
* task: Don't discard events on mutex contentionShawn Nematbakhsh2015-11-302-7/+3
* kunimitsu: Modify battery LED colourMike M Hsieh2015-11-301-12/+4
* Chell: support LED behaviorBruce2015-11-291-68/+50
* Lars: update type-C switch port countRyan Zhang2015-11-272-5/+1
* Lars: update i2c.mux speedRyan Zhang2015-11-271-1/+1
* kunimitsu: remove fab 3 related changesKevin K Wong2015-11-261-12/+1
* ec3po: Add compatibility for older EC images.Aseda Aboagye2015-11-265-317/+900
* Lars: update GPIO settingRyan Zhang2015-11-251-39/+39
* oak: add VCONN swap abilityBen Lok2015-11-252-0/+10
View Lorry Controller Status