summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* Zork/Trembyle: initial setupMartin Roth2019-05-2113-0/+1941
* I2C: Make pass-through debug messages more informativeDaisuke Nojiri2019-05-211-22/+24
* USB-PD: Consolidate tcpc_config declarations in usb_pd_tcpm.hDaisuke Nojiri2019-05-213-6/+6
* cr50: Generate new G2F seed.Louis Collard2019-05-212-1/+8
* cr50: Change G2F cert CN to "CrOS"Louis Collard2019-05-213-9/+23
* Makefiles.rules: Do not attempt to run fuzzing testsNicolas Boichat2019-05-211-1/+2
* servo_v4: Enable VBUS voltage and current measurementWai-Hong Tam2019-05-202-0/+6
* servo_v4: Disable syslock and flash commandsWai-Hong Tam2019-05-201-0/+2
* servo_v4: Disable unused features to reduce spaceWai-Hong Tam2019-05-201-0/+3
* common: add __maybe_unused attributeJack Rosenthal2019-05-201-0/+11
* tabletmode: ignore lid angle if hall sensor activeJett Rink2019-05-183-15/+42
* ish: fix printf format for idlestats commandJack Rosenthal2019-05-181-11/+11
* USB PD: Don't attempt to exit mode on a suspended portDiana Z2019-05-171-11/+29
* servo_v4: fix in displaying CCD polarityNamyoon Woo2019-05-171-1/+1
* flash_ec: prevent null entry in dut-control recovery listNamyoon Woo2019-05-171-2/+8
* g: do not destroy manufacturing space by flasheraseVadim Bendebury2019-05-172-5/+11
* common: chip_save_reset_flags takes uint32_tJack Rosenthal2019-05-175-5/+5
* pd_protocol: Add ready_state_holdoff_timer.Aseda Aboagye2019-05-171-17/+44
* servo_v4: Remove console command history.Aseda Aboagye2019-05-171-0/+1
* bq25710: Adjust settings to limit VSYS droop with no batteryScott Collyer2019-05-172-7/+59
* kohaku: Add support for Dyna batteryScott Collyer2019-05-172-39/+10
* kohaku: Fix the GPIO pin assignment for USB_C0_BC12_CHG_DET_LScott Collyer2019-05-171-1/+1
* flash_ec: expand the list of directories where npcx_monitor.bin can be foundPaul Fagerburg2019-05-171-9/+16
* board: arcada: Fix magnetometer axis rotationYuval Peress2019-05-161-1/+1
* ish: fix reading current interrupt vectorHyungwoo Yang2019-05-162-4/+5
* i2c: add i2clookup host commandJett Rink2019-05-163-1/+110
* tcpci/usb_pd_fuzz: Avoid using unitialized data in payloadNicolas Boichat2019-05-162-1/+7
* FIXUP: driver: lis2mdl: add standalone supportGwendal Grignou2019-05-161-2/+2
* ish: save and restore reset flags across resetJack Rosenthal2019-05-162-8/+28
* ish: move panic data into AON ROMJack Rosenthal2019-05-161-4/+7
* ish: increase AON ROM size by 256 bytesJack Rosenthal2019-05-163-5/+9
* ec: common: Make IS_ENABLED fail on unknown valuesRaul E Rangel2019-05-1510-19/+175
* charge_manager: Revisit charge supplier priority.stabilize-12206.BYilun Lin2019-05-144-19/+58
* ish: fix GPIO interrupt enabling and statusHyungwoo Yang2019-05-141-0/+5
* retimer: Add driver support for Intel Burnside Bridge retimerVijay Hiremath2019-05-148-0/+429
* host: Fix test breakageRaul E Rangel2019-05-141-0/+2
* ish: set firmware status to running during pre-initJack Rosenthal2019-05-141-0/+3
* queue.h: Check at compile time if queue size is power of 2Nicolas Boichat2019-05-142-2/+1
* Align behavior of strtoi() and strtoul() to match Linux manpage description o...Jes Klinke2019-05-142-28/+128
* baseboard: hatch: Limit printf on serial consoleGwendal Grignou2019-05-141-0/+8
* kukui: Enable interrupts from hall sensor.Yilun Lin2019-05-143-8/+4
* kukui: Loose charging 5V limitation strategy.Yilun Lin2019-05-141-17/+21
* ish: add more explanations comments for reset flow in aontaskJett Rink2019-05-141-3/+29
* ish: fix lapic table readJett Rink2019-05-142-5/+9
* ish: update firmware statusHyungwoo Yang2019-05-142-0/+5
* ish: fix bugs in fwst check functionsHyungwoo Yang2019-05-141-2/+2
* iteflash: use serial number to find the ccd deviceMary Ruthven2019-05-141-9/+4
* ish: correct gpio voltage to 3.3Vstabilize-12202.BJett Rink2019-05-131-1/+1
* ish/ish5: fixed both-edge triggered gpio configuration blocking D0ix issueHu, Hebo2019-05-122-42/+97
* ccd doc: link to suzyq instructions in cr50 setupMary Ruthven2019-05-121-2/+4
View Lorry Controller Status