summaryrefslogtreecommitdiff
path: root/baseboard/grunt
Commit message (Expand)AuthorAgeFilesLines
* treeya: apply USB EQ setting to PS8751 USB muxLu Zhang2019-10-151-1/+12
* printf: Fix formatting errorsEvan Green2019-10-051-1/+1
* config: Merge CONFIG_CHARGER_V2 into CONFIG_CHARGERKeith Short2019-09-181-1/+0
* config: Refactor CONFIG_ACCEL_FIFO to enable use of IS_ENABLEDYuval Peress2019-09-031-3/+4
* grunt: Disable ec_feature kbbacklit for barla refresh SKUsDevin Lu2019-08-291-0/+1
* common: Move fifo logic out of motion_sense.cYuval Peress2019-08-231-0/+2
* treeya: enable motion sensor drivers and fix ec feature flagPaul Ma2019-08-211-2/+6
* Grunt/Treeya: Add ANX3447 variant for TCPC 0.Paul Ma2019-08-212-1/+195
* Remove __7b, __8b and __7bfDenis Brockus2019-07-201-7/+7
* Use 7bit I2C/SPI slave addresses in ECDenis Brockus2019-07-191-7/+7
* grunt: Wake from hibernate on EC resetEdward Hill2019-06-141-7/+0
* TCPC: Make tcpc_config handle other bus typesDaisuke Nojiri2019-06-101-4/+10
* common: motion_sense: Require CONFIG_MOTION_SENSOR_MAX_COUNTYuval Peress2019-06-051-0/+1
* grunt: Improve safe state when entering DP modeEdward Hill2019-04-241-31/+37
* tcpm: Refactor tcpc_config to include a flags fieldScott Collyer2019-04-171-3/+4
* grunt/usb_pd_policy: Don't disconnect the USB lines while negotiating PDRaul E Rangel2019-04-091-2/+12
* grunt: Check IRQ and HPD in DPStatus message.Edward Hill2019-03-261-1/+1
* grunt: Check DP MF-bit against selected pin cfgEdward Hill2019-03-261-2/+12
* aleena: Enable GPIO-based MKBP event notificationEdward Hill2019-02-121-1/+0
* grunt: Reduce the sensor FIFO sizeEnrico Granata2019-02-061-1/+1
* Aleena/Kasumi: Add LID sensor config in S0David Huang2019-01-261-0/+5
* aleena/kasumi: Add support for motion sensorsEdward Hill2018-12-052-12/+18
* grunt: Enable PPC sink FET before hibernatingEdward Hill2018-11-271-0/+13
* grunt: Enable CONFIG_LOW_POWER_IDLE and CONFIG_LOW_POWER_S0Edward Hill2018-11-211-1/+3
* cleanup: updating grunt & octopus style to matchJett Rink2018-11-141-9/+8
* SN5S330: treat interrupts as level-sensitiveDiana Z2018-11-132-0/+10
* careena: Limit input current to fraction of negotiated limitDevin Lu2018-11-131-0/+5
* delan: Use CBI EEPROM for board version and SKU IDEdward Hill2018-10-282-7/+55
* grunt: Increase port80 buffer to 256 bytesEdward Hill2018-10-231-0/+3
* grunt: Add minimal analyzestack configurationsJonathan Brandmeyer2018-10-051-0/+2
* careena, liara, aleena: Remove motion sensing supportJonathan Brandmeyer2018-10-041-18/+0
* grunt: Reduce PD turn off delayEdward Hill2018-10-041-4/+2
* grunt: Move KSI03 HW bug work around out of baseboardEdward Hill2018-10-041-2/+0
* bc12: rename bq24392 driver to max14637Scott Collyer2018-10-022-5/+5
* grunt: Disable ec_feature kbbacklit by SKUID for barlaDevin Lu2018-09-211-1/+2
* Careena: Disable motion sensorsJonathan Brandmeyer2018-09-192-1/+2
* ss-mux: remove unused port_addr initializationv2.0.0Jett Rink2018-09-171-2/+0
* type: Rename matrix_3x3_t to mat33_fp_tYilun Lin2018-09-132-6/+6
* keyboard: Ignore refresh button at bootDaisuke Nojiri2018-09-071-1/+0
* grunt: Use higher priority TCPC interrupt tasks.Jonathan Brandmeyer2018-09-072-0/+23
* grunt: Enable CONFIG_I2C_BUS_MAY_BE_UNPOWEREDEdward Hill2018-09-052-1/+11
* Add CONFIG_GPIO_INIT_POWER_ON_DELAY_MSEdward Hill2018-09-041-0/+9
* grunt: Configure ANX3429 interrupt as open-drainEdward Hill2018-08-311-0/+1
* grunt: Complete PD negotiation before kernel start.Jonathan Brandmeyer2018-08-311-1/+15
* servo_v4: add per port dualrole settingNick Sanders2018-08-151-2/+2
* grunt: Enable LTOJonathan Brandmeyer2018-08-151-0/+1
* careena: Correct baseboard IMU orientation.Jonathan Brandmeyer2018-07-312-16/+22
* reset: Log the reason for AP resets.Jonathan Brandmeyer2018-07-261-0/+1
* grunt,careena: Raise the charger current supremum.Jonathan Brandmeyer2018-07-111-1/+12
* motion_sense: Provide option to defer resume actions.Jonathan Brandmeyer2018-06-281-0/+5
View Lorry Controller Status