summaryrefslogtreecommitdiff
path: root/baseboard/zork
Commit message (Expand)AuthorAgeFilesLines
...
* morphius: update ps8818 usb rx settingZick Wei2020-10-152-0/+11
* TBT:Add support for exit mode SOP'/SOP'' on chipset transitionAyushee2020-10-141-1/+6
* zork: Workaround VBUS=0 for charge_ramp_swEdward Hill2020-09-301-3/+22
* Revert "Zork: Workaround for bad ISL9241 CONTROL1 read"Edward Hill2020-09-291-30/+0
* berknip: Remove sensorsEdward Hill2020-09-291-0/+2
* zork: Ignore input current and always rampEdward Hill2020-09-231-0/+10
* zork: Update PS8802/PS8818 IN_HPD to match HW changesEdward Hill2020-09-232-4/+7
* zork: Disable CONFIG_KEYBOARD_VIVALDIEdward Hill2020-09-231-0/+1
* zork: move HDMI retimer setting to variantZick Wei2020-09-221-7/+0
* zork: Adjust AP power limitsEdward Hill2020-09-171-11/+5
* zork: Re-Enable CONFIG_CHARGE_RAMP_SWEdward Hill2020-09-022-0/+27
* Revert "zork: Enable CONFIG_CHARGE_RAMP_SW"Denis Brockus2020-08-312-27/+0
* zork: Remove debug printEdward Hill2020-08-311-1/+0
* zork: Enable CONFIG_CHARGE_RAMP_SWEdward Hill2020-08-302-0/+28
* zork: Use gpio_or_ioex_set_level for PORT_TO_HPDEdward Hill2020-08-291-2/+2
* zork: Delay between G3 exit and power buttonEdward Hill2020-08-292-0/+21
* Ezkinil: Fix HDMI retimer suspend / resumeEdward Hill2020-08-222-16/+0
* Zork: Workaround for bad ISL9241 CONTROL1 readSue Chen2020-08-221-0/+30
* trembyle: correctly pass USB-C1 HPD to the MST hubPeter Marheine2020-08-212-2/+32
* Zork: Add command to print temps periodicallyEdward Hill2020-08-202-0/+44
* Zork: Remove CONFIG_CHARGE_RAMP_HWEdward Hill2020-08-131-1/+0
* trembyle: Use board_version for I2C_PORT_CHARGER_V0Edward Hill2020-08-111-19/+0
* Ezkinil: Add AOZ1380 for DB TYPEC C1Sue Chen2020-08-071-1/+1
* isl9241: Set AC prochotEdward Hill2020-08-052-0/+10
* zork: move board_get_temp to variantZick Wei2020-08-033-32/+33
* zork: don't turn off vbus if we aren't sourcing vbusDenis Brockus2020-07-281-10/+9
* zork: Re-enable CONFIG_KEYBOARD_VIVALDIEdward Hill2020-07-201-1/+0
* zork: Use CBI only and remove retimer probe codeDenis Brockus2020-07-172-12/+1
* zork: Enable 65W/3.25A PD adapter.Lu Zhang2020-07-171-2/+2
* USB PD: Move board FRS configuration out of TCPCIEric Herrmann2020-07-172-5/+1
* zork: Enable CONFIG_I2C_UPDATE_IF_CHANGEDEdward Hill2020-07-131-0/+1
* Zork: Handle USB_Cx_SBU_FAULT_ODLEdward Hill2020-07-123-0/+12
* Charger: Add dynamic charger chip countDiana Z2020-07-112-3/+0
* Zork: remove pd_snk_is_vbus_providedEdward Hill2020-07-101-5/+0
* Zork: Remove CONFIG_HOSTCMD_SKUIDEdward Hill2020-07-082-18/+9
* Revert "TCPMv2: make sure Vbus is not sourced in AttachWait.SRC"Denis Brockus2020-07-081-4/+2
* woomax: Update USB-A and FW_CONFIGEdward Hill2020-07-032-15/+0
* TCPMv2: make sure Vbus is not sourced in AttachWait.SRCDenis Brockus2020-07-011-2/+4
* berknip/morphius: update gpio S0_PWROK_ODZick Wei2020-06-252-24/+25
* npcx: Add a new flag to check for initial power-onAndrew McRae2020-06-231-4/+3
* Zork: Don't KB_SCAN_DISABLE_LID_ANGLE in S0Edward Hill2020-06-201-2/+17
* morphius: add ppc aoz1380Zick Wei2020-06-192-2/+2
* TCPMv2: Add pathway to enable FRS from PPC driverEric Herrmann2020-06-181-2/+2
* berknip: add 5V regulator temperature sensorDevin Lu2020-06-152-2/+4
* zork/baseboard: move temperature sensors definition to board variantDevin Lu2020-06-153-70/+48
* Zork: Disable PI3HDX1204 when HDMI didn't connect.David Huang2020-06-132-2/+11
* TCPMv2: Support mode entry for SOP' and SOP''Abe Levkoy2020-06-111-1/+1
* vilboz: Remove ioex C1 and config the ioexpander gpioLu Zhang2020-06-113-19/+21
* vilboz: Split mux to dalboz and vilbozLu Zhang2020-06-104-91/+18
* Ezkinil: modify some gpio definitionSue2020-06-052-22/+0
View Lorry Controller Status