summaryrefslogtreecommitdiff
path: root/baseboard
Commit message (Expand)AuthorAgeFilesLines
* Power_x86: Correct the debounce delay for SYS_RESET_L signalKattamuri, Sowjanya2020-04-081-0/+11
* grunt/baseboard: Slow keyboard scan rateDevin Lu2020-04-081-2/+7
* volteer: Move GPIO runtime configuration from baseboardKeith Short2020-04-082-22/+15
* Dedede: Configure sensor ports as unpowered in S5/G3Diana Z2020-04-082-0/+10
* zork: move thermal setting to variantZick Wei2020-04-071-58/+0
* it83xx/gpio: disable unused cc port moduleRuibin Chang2020-04-074-0/+4
* Zork: avoid losing edges from MST hub to DP1_HPDEdward Hill2020-04-071-2/+12
* Revert "volteer: Disable Burnside Bridge with TCPMv2"Ayushee2020-03-312-11/+1
* baseboard/kukui: correct FUSB302 VBUS turn-on delayEric Yilun Lin2020-03-311-4/+12
* volteer: Select LED based on charge portAbe Levkoy2020-03-302-4/+27
* Trogdor: Create Trogdor baseboardWai-Hong Tam2020-03-304-0/+544
* Zork: Clean up FW_CONFIG hook functionsEdward Hill2020-03-282-8/+0
* tcpmv2: reduce zork specific auto discharge disconnect codeDenis Brockus2020-03-281-1/+0
* Volteer: add monitoring for PROCHOT inputKeith Short2020-03-282-0/+4
* config: update TCPMv2 config optionsJett Rink2020-03-271-3/+0
* x86: Make board_has_[before|after]_rsmrst overridableAseda Aboagye2020-03-261-1/+1
* zork: undo revert for zork on AutoDischargeDisconnectDenis Brockus2020-03-261-0/+1
* kakadu: add new battery support for gauge max17055Scott Chao2020-03-261-4/+53
* hatch/baseboard: Increase TCPC i2c speed to 400KhzDevin Lu2020-03-261-2/+2
* Ezkinil: Add redriver TUSB544 and PS8743 for EzkinilDavid Huang2020-03-262-0/+14
* malefor: move sensors support from baseboard to boardxiong.huang2020-03-263-207/+0
* cleanup: drop the _TYPEC part of USB device configJett Rink2020-03-263-3/+3
* Waddledee: Set up ADC thresholds for PP3300_A_PGOODDiana Z2020-03-262-1/+63
* Waddledee: Configure DAC for PSYSDiana Z2020-03-261-5/+5
* volteer: enable ps8815 on USB3 daughter boardCaveh Jalali2020-03-251-3/+12
* Waddledee: Complete basic EC tasksDiana Z2020-03-242-5/+270
* nucleo-f412zg: Initial board offeringCraig Hesling2020-03-246-0/+275
* dedede: Check PG_VCCIO_EXT for ALL_SYS_PGOODAseda Aboagye2020-03-241-2/+4
* nct38xx: Remove ioexpander_nct38xx.hEdward Hill2020-03-202-2/+2
* dalboz: Set usb_port_enable[] for DB optionEdward Hill2020-03-203-3/+10
* dalboz: select GPIOs based on DB optionEdward Hill2020-03-203-20/+25
* zork: split baseboard_tcpc_init to trembyle and dalbozEdward Hill2020-03-203-22/+40
* zork: split ioex_config[] to trembyle and dalbozEdward Hill2020-03-204-17/+53
* zork: Use only AutoDischargeDisconnect to DischargeDenis Brockus2020-03-201-1/+0
* zork: allow AutoDischargeDisconnect to be sole DischargeDenis Brockus2020-03-201-2/+3
* zork: cleanup TCPMvX selection in case of roll back needsDenis Brockus2020-03-201-7/+10
* volteer: Switch to TCPC VBUS detectAbe Levkoy2020-03-181-1/+1
* volteer: enable battery cutoffKeith Short2020-03-171-3/+1
* kukui: increase PD_POWER_SUPPLY_TURN_OFF_DELAYTing Shen2020-03-171-1/+1
* Juniper: Return BP_NOT_SURE when DFET status is offDavid Huang2020-03-172-2/+22
* Dedede: Configure PROCHOT as active lowDiana Z2020-03-161-0/+1
* OCPC: Introduce charger enumDiana Z2020-03-161-0/+6
* volteer: enable DRP auto toggle and TCPC low powerKeith Short2020-03-131-2/+4
* kukui/dynamic-pdo: setting input current limit correctlyEric Yilun Lin2020-03-131-7/+17
* Mushu : enable GPU temperature sensor driver in Mushuloganliao2020-03-131-0/+3
* baseboard/ite_evb: create ite_evb baseboardRuibin Chang2020-03-124-0/+397
* dedede: Require >15W to boot without a batteryAseda Aboagye2020-03-121-0/+2
* variant trembyle: use fw_config for mux initializationDenis Brockus2020-03-125-220/+22
* trembyle: change set_mux calls to be board namesDenis Brockus2020-03-111-4/+6
* trembyle: move ps8811 from variant to boardDenis Brockus2020-03-111-56/+0
View Lorry Controller Status