summaryrefslogtreecommitdiff
path: root/board/dalboz
Commit message (Expand)AuthorAgeFilesLines
* zork: move HDMI retimer setting to variantZick Wei2020-09-221-0/+7
* zork: Re-Enable CONFIG_CHARGE_RAMP_SWEdward Hill2020-09-021-0/+1
* Revert "zork: Enable CONFIG_CHARGE_RAMP_SW"Denis Brockus2020-08-311-1/+0
* zork: Enable CONFIG_CHARGE_RAMP_SWEdward Hill2020-08-301-0/+1
* Dalboz: Fix HDMI retimer suspend / resumeEdward Hill2020-08-221-13/+21
* Dalboz/Dirinboz: Consolidate retimer power control functionsJosie Nordrum2020-08-171-12/+6
* Dalboz: Daughterboard IO expander pin IO5 new function EN_PWR_HDMI_DBJosie Nordrum2020-08-122-0/+19
* Dalboz: Enable internal pull up for EC GPIOD4Josie Nordrum2020-08-121-1/+1
* dalboz: Use board_version for I2C_PORT_BATTERY_V0Edward Hill2020-08-111-10/+11
* USB PD: Move board FRS configuration out of TCPCIEric Herrmann2020-07-171-1/+1
* Zork: Handle USB_Cx_SBU_FAULT_ODLEdward Hill2020-07-122-2/+7
* Zork: Remove CONFIG_SYSTEM_UNLOCKEDEdward Hill2020-07-091-7/+0
* Revert "TCPMv2: make sure Vbus is not sourced in AttachWait.SRC"Denis Brockus2020-07-081-4/+2
* woomax: Update USB-A and FW_CONFIGEdward Hill2020-07-031-7/+11
* TCPMv2: make sure Vbus is not sourced in AttachWait.SRCDenis Brockus2020-07-011-2/+4
* Zork: Change 3AXIS_INT_L to GPIO_PULL_DOWNEdward Hill2020-06-191-1/+1
* dalboz: move HDMI HPD off the IO expanderPeter Marheine2020-06-192-9/+20
* zork/baseboard: move temperature sensors definition to board variantDevin Lu2020-06-151-0/+13
* vilboz: Remove ioex C1 and config the ioexpander gpioLu Zhang2020-06-112-0/+22
* vilboz: Split mux to dalboz and vilbozLu Zhang2020-06-102-0/+88
* zork: Move tcpc,ppc,bc12 from baseboard to boardLu Zhang2020-06-052-0/+219
* vilboz: Remove PCAL6408 entirely and enable HDMILu Zhang2020-06-052-0/+69
* Zork: Switch PS8743 from IOEX_USB_C1_DATA_EN to I2CEdward Hill2020-06-031-14/+8
* PD: Remove unnecessary PDCMD taskDiana Z2020-05-201-1/+0
* Zork: Enable EFS2Daisuke Nojiri2020-05-061-0/+1
* Zork: Add PI3HDX1204 power control.Edward Hill2020-05-051-0/+9
* Zork: Configure GPIO86 EC_H1_PACKET_MODE lowEdward Hill2020-04-291-0/+1
* dalboz: let i2c control ps8743 DP/USB/FLIP selectionPaul Ma2020-04-261-0/+21
* Dalboz: Support PS8743 and PS8740 HWEdward Hill2020-04-161-0/+16
* Dalboz: Move battery I2C on V1 HWEdward Hill2020-04-153-6/+28
* dalboz: add power led supportLu Zhang2020-04-153-10/+48
* dalboz: use physical pin to generate SCI to SOCPaul Ma2020-04-012-0/+4
* Zork: Clean up FW_CONFIG hook functionsEdward Hill2020-03-281-7/+13
* dalboz: Remove CONFIG_BRINGUPLu Zhang2020-03-241-1/+0
* dalboz: Set IOEX interrupt handler for DB optionEdward Hill2020-03-202-2/+25
* dalboz: Set usb_port_enable[] for DB optionEdward Hill2020-03-201-0/+2
* dalboz: select GPIOs based on DB optionEdward Hill2020-03-203-7/+55
* zork: split ioex_config[] to trembyle and dalbozEdward Hill2020-03-201-21/+21
* zork: add EC fw_config frameworkDenis Brockus2020-03-101-1/+68
* dalboz: fix rotation matrixLu Zhang2020-03-041-2/+9
* zork: Split mux/retimer for trembyle/dalbozEdward Hill2020-02-291-0/+1
* dalboz: update GPIOsEdward Hill2020-02-273-35/+5
* zork: Move fan into variant_trembyle.cEdward Hill2020-02-273-24/+0
* zork: Create baseboard variants for trembyle/dalbozEdward Hill2020-02-271-0/+2
* dalboz: Add base/lid sensor configurationLu Zhang2020-02-263-5/+105
* dalboz: Add battery informationLu Zhang2020-02-252-20/+81
* dalboz/ezkinil: Connect up HPD interruptsEdward Hill2020-02-141-2/+3
* zork: Sync GPIO changesEdward Hill2020-02-141-2/+2
* morphius: add PWM CH0 for LED controlZick Wei2020-02-112-0/+40
* dalboz: Initial EC imageMartin Roth2020-02-078-0/+429
View Lorry Controller Status