summaryrefslogtreecommitdiff
path: root/board/glados
Commit message (Expand)AuthorAgeFilesLines
* glados: oak: chell: enable USB PD loggingAlec Berg2015-10-301-0/+2
* glados: oak: reboot EC if PD MCU crashesAlec Berg2015-10-231-0/+1
* mec1322: Remove CONFIG_PORT80_TASK_EN from boards.Aseda Aboagye2015-10-231-1/+0
* glados: chell: add VCONN swap abilityAlec Berg2015-10-232-0/+10
* pd: change battery and variable sink cap for voltage inaccuracyAlec Berg2015-10-231-2/+2
* mec1322: Change the Port 80 task to a timer IRQ.Aseda Aboagye2015-10-191-2/+2
* glados / kunimitsu / chell: Slow EC-->PD I2C bus to 500 KHzShawn Nematbakhsh2015-10-151-1/+1
* Skylake: Configure EC to use W25X40 flash instead of W25Q64Shamile Khan2015-10-151-1/+1
* GLaDOS: Kunimitsu: Chell: Reduce UART TX buffer to 512B.Aseda Aboagye2015-10-151-0/+3
* glados: kunimitsu: Change image size to 100K.stabilize-smaug-7547.BAseda Aboagye2015-10-131-0/+3
* cleanup: pd: remove duplicate code for checking request msgAlec Berg2015-10-131-26/+0
* skylake: Move USB enable gpio control to board hooksDuncan Laurie2015-10-121-0/+4
* glados: Add support for volume buttonsShawn Nematbakhsh2015-10-062-4/+6
* glados: set max input power to 45WAlec Berg2015-10-061-1/+1
* glados / glados_pd: Hibernate the PD when the EC hibernatesShawn Nematbakhsh2015-10-052-5/+10
* ALS: Disable the ALS task if all the ALS inits failVijay Hiremath2015-10-021-1/+1
* glados: Swap pericom usb2 charge detector portsShawn Nematbakhsh2015-09-241-3/+2
* GLaDOS: Add base accel & gyro.Aseda Aboagye2015-09-192-2/+83
* pd: set USB communications capable flag in PDOAlec Berg2015-09-181-1/+2
* GLaDOS: Add lid accelerometer.Aseda Aboagye2015-09-172-0/+53
* cleanup: Remove redundant FLASH_SIZE CONFIGsShawn Nematbakhsh2015-09-161-1/+1
* GLaDOS: Add 3ms delay to end of chipset_resume.Aseda Aboagye2015-09-151-1/+15
* glados: Power-off PP1800_DX_AUDIO during S3Shawn Nematbakhsh2015-09-111-2/+2
* temp_sensor: Separate ADC interface and thermistor mathsWonjoon Lee2015-09-111-0/+1
* glados: Enable TI OPT3001 ambient light sensorDuncan Laurie2015-09-103-0/+21
* glados: Enable low-power idleShawn Nematbakhsh2015-09-103-1/+4
* glados: Remove console commands to shrink image sizeShawn Nematbakhsh2015-09-101-0/+2
* glados: kunimitsu: remove dual-port charge enable workaroundAlec Berg2015-09-092-19/+7
* glados: document behavior of SLP_S0_LAaron Durbin2015-08-311-0/+6
* glados: increase voltage hysteresis in fast chargingAlec Berg2015-08-281-2/+2
* glados: implement x86 power cycle on EC resetAaron Durbin2015-08-262-2/+41
* glados: disable console historyAaron Durbin2015-08-261-0/+1
* glados: enable CONFIG_BOARD_VERSIONAaron Durbin2015-08-272-3/+4
* glados: Increase stack size for powerbtn taskShawn Nematbakhsh2015-08-261-1/+1
* glados: oak: Add charger AMONBMON console commandRong Chang2015-08-251-0/+1
* glados: Disable keyboard + trackpad in tablet modeShawn Nematbakhsh2015-08-243-6/+42
* glados: Enable CONFIG_VBOOT_HASHShawn Nematbakhsh2015-08-201-2/+3
* glados: Remove console commands to reduce image sizeShawn Nematbakhsh2015-08-201-0/+2
* glados: make BATLOW_L open drain and default highAaron Durbin2015-08-191-1/+1
* glados: don't pull up SLP_S0_LAaron Durbin2015-08-191-1/+1
* glados: Switch to V2 boardShawn Nematbakhsh2015-08-143-66/+1
* glados: Revise PMIC initializationShawn Nematbakhsh2015-08-121-2/+7
* glados: Enable `tests` buildShawn Nematbakhsh2015-08-121-0/+2
* glados: Turn off LEDs in hibernateShawn Nematbakhsh2015-08-111-0/+30
* glados: Implement LED functionality on ECMike Hsieh2015-08-082-3/+140
* usb_charger: move common usb charger code out of board directoryAlec Berg2015-08-051-55/+4
* usb_charger: configure boards to disconnect USB when UFP.Alec Berg2015-08-041-0/+1
* usb_charger: cleanup: move setting usb 2 switches to usb_chargerAlec Berg2015-08-041-5/+0
* glados: Add bd99992gw temperature sensorsShawn Nematbakhsh2015-08-032-1/+26
* skylake: Inhibit AP power-on until charge current limit is setShawn Nematbakhsh2015-08-011-0/+1
View Lorry Controller Status