summaryrefslogtreecommitdiff
path: root/board/glados
Commit message (Expand)AuthorAgeFilesLines
* Remove Makefile symlinks under board directoryDaisuke Nojiri2016-07-091-1/+0
* common: Decouple temp sensor from thermal throttlingMary Ruthven2016-06-281-0/+1
* BD99955: Added support for 'psys' & 'amonbmon' console commandsVijay Hiremath2016-06-271-1/+1
* cleanup: pd: Define VBUS detection sourceShawn Nematbakhsh2016-06-021-0/+1
* Driver: BD99955: Enable BC1.2 supportVijay Hiremath2016-05-241-1/+3
* Deferred: Remove hard coded number of deferredsAnton Staaf2016-04-191-3/+0
* Deferred: Use deferred_data instead of function pointerAnton Staaf2016-04-182-6/+7
* tcpm: update code to support multiple tcpm driverKevin K Wong2016-04-171-2/+3
* charge_manager: Report UNKNOWN USB charger for 2 seconds after changeShawn Nematbakhsh2016-04-031-1/+1
* sensor: update sensor driver to use I2C port from motion_sensor_tKevin K Wong2016-03-311-0/+3
* GPIO: Rename and move board_set_gpio_hibernate_stateAnton Staaf2016-03-211-1/+1
* cleanup: Add warning comment to gpio.inc filesBill Richardson2016-02-252-0/+6
* GPIO: Move definitions of GPIO_KB_INPUT and OUTPUTAnton Staaf2016-02-222-3/+3
* mec1322: clock: Use full-speed 48MHz processor clock during EC bootShawn Nematbakhsh2016-02-091-1/+1
* glados / chell: Power Optimize S0ix PMIC VRsShawn Nematbakhsh2016-01-261-0/+12
* chell/glados/kunimitsu/tlars: Enable temporary host storageDuncan Laurie2016-01-251-4/+13
* mec1322: hibernate: Don't reconfigure all GPIOsShawn Nematbakhsh2016-01-251-24/+10
* GPIO: Use gpio_set_flags instead of ..._by_maskAnton Staaf2016-01-191-2/+1
* glados / kunimitsu: led: battery LED blinking on low batteryli feng2016-01-151-2/+4
* Skylake: prevent EC from continuing execution after turning 3.3V_DSW off.Kyoung Kim2016-01-131-0/+2
* glados/chell: Do not pull-up RSMRST to PCH in hibernateDuncan Laurie2015-12-091-0/+2
* pd: send power change event to AP whenever input power is changedBen Lok2015-12-011-0/+5
* glados: Make SLP_S0 a non-interrupt input pinShawn Nematbakhsh2015-11-193-9/+9
* chell / glados: Add power signal interrupt storm detectionShawn Nematbakhsh2015-11-191-0/+1
* motion: Change units of ec_rate from us to ms.Gwendal Grignou2015-11-181-3/+3
* glados / chell: Enable useful console featuresShawn Nematbakhsh2015-11-171-3/+0
* glados/chell: drive PCH_RTCRST lowAaron Durbin2015-11-122-1/+3
* glados: Add pullup to SPI MISO GPIOShawn Nematbakhsh2015-11-111-1/+1
* GLaDOS: Kunimitsu: Enable link-time optimization.Aseda Aboagye2015-11-091-0/+1
* mec1322: adjust mec adc channels for analog reference of 3.0VAlec Berg2015-11-091-3/+3
* glados: isl9237: add HW charge rampingAlec Berg2015-11-092-0/+35
* tcpm: Add configuration struct for tcpc i2c paramsShawn Nematbakhsh2015-11-081-0/+5
* chg: add narrow VDC power path supportRong Chang2015-11-051-0/+1
* mec1322: reduce system stack sizeli feng2015-11-041-1/+1
* led: correct LED blinking intervalli feng2015-11-041-4/+4
* cleanup: Standardize use of CONFIG_I2C and add MASTER/SLAVE CONFIGsShawn Nematbakhsh2015-11-031-0/+1
* glados: oak: chell: enable USB PD loggingAlec Berg2015-10-301-0/+2
* glados: oak: reboot EC if PD MCU crashesAlec Berg2015-10-231-0/+1
* mec1322: Remove CONFIG_PORT80_TASK_EN from boards.Aseda Aboagye2015-10-231-1/+0
* glados: chell: add VCONN swap abilityAlec Berg2015-10-232-0/+10
* pd: change battery and variable sink cap for voltage inaccuracyAlec Berg2015-10-231-2/+2
* mec1322: Change the Port 80 task to a timer IRQ.Aseda Aboagye2015-10-191-2/+2
* glados / kunimitsu / chell: Slow EC-->PD I2C bus to 500 KHzShawn Nematbakhsh2015-10-151-1/+1
* Skylake: Configure EC to use W25X40 flash instead of W25Q64Shamile Khan2015-10-151-1/+1
* GLaDOS: Kunimitsu: Chell: Reduce UART TX buffer to 512B.Aseda Aboagye2015-10-151-0/+3
* glados: kunimitsu: Change image size to 100K.stabilize-smaug-7547.BAseda Aboagye2015-10-131-0/+3
* cleanup: pd: remove duplicate code for checking request msgAlec Berg2015-10-131-26/+0
* skylake: Move USB enable gpio control to board hooksDuncan Laurie2015-10-121-0/+4
* glados: Add support for volume buttonsShawn Nematbakhsh2015-10-062-4/+6
* glados: set max input power to 45WAlec Berg2015-10-061-1/+1
View Lorry Controller Status