summaryrefslogtreecommitdiff
path: root/board/grunt
Commit message (Expand)AuthorAgeFilesLines
...
* grunt: Add power/battery LED supportSimon Glass2018-02-164-173/+58
* grunt: Add pull-up to EC_BATT_PRES_ODL GPIOEdward Hill2018-02-161-1/+1
* grunt: Remove pull-up on UART pins.Aseda Aboagye2018-02-151-1/+2
* grunt: Disable system power (_A rails) in G3Edward Hill2018-02-121-1/+1
* grunt: Turn PP1800_SENSOR off in S5Edward Hill2018-02-092-1/+19
* grunt: Making control of SCI and SMI interrupt pins more clearJett Rink2018-02-091-2/+5
* grunt: Set USB-C DP HPD GPIOs correctly.Edward Hill2018-02-011-7/+49
* Grunt: Set AP reset pin to open drainMartin Roth2018-02-011-1/+1
* grunt: Rename orange LED to amberSimon Glass2018-02-012-3/+3
* cleanup: Removing unnecessary CONFIG_USB_PD_DISCHARGE defineJett Rink2018-02-011-1/+0
* grunt: enabling PPC vbus discharge pathJett Rink2018-01-311-1/+1
* sn5s330: Enable VBUS interruptsEdward Hill2018-01-311-10/+1
* cleanup: Remove CONFIG_USB_PD_TCPC_BOARD_INITShawn Nematbakhsh2018-01-301-1/+0
* grunt: Disable CONFIG_BRINGUP optionMartin Roth2018-01-261-2/+0
* grunt: Enable LM3630A driver for keyboard backlightBenjamin Gordon2018-01-252-0/+11
* grunt: Add CONFIG_VSTOREDaniel Kurtz2018-01-241-0/+7
* grunt: Move TCPC init to init hookEdward Hill2018-01-232-1/+1
* grunt: Enable TCPC/PPC interrupts in board_tcpc_initEdward Hill2018-01-191-11/+5
* grunt: Add USB-C DP Hotplug Detect GPIOsEdward Hill2018-01-191-0/+2
* grunt: Add PWMs for battery / charger LEDsstabilize-10323.31.Bstabilize-10323.30.Bstabilize-10323.29.Bfactory-soraka-10323.BSimon Glass2018-01-183-2/+22
* grunt: Enabling backlight lid control moduleJett Rink2018-01-182-8/+14
* grunt: Add support for I2C bus 5Simon Glass2018-01-182-0/+2
* grunt: Enable TCPC + PPC interrupts and overcurrent GPIOsEdward Hill2018-01-162-3/+23
* grunt: Set source current limit to enable 3A outputEdward Hill2018-01-161-4/+8
* grunt: Don't return error when disabling all charge portsEdward Hill2018-01-161-8/+4
* grunt: Fix ENABLE_BACKLIGHT to be active lowEdward Hill2018-01-142-1/+15
* grunt: Enable BMI160 gyro interruptsEdward Hill2018-01-142-1/+8
* grunt: Add CONFIG_VBOOT_HASHEdward Hill2018-01-141-7/+4
* grunt: Add I2C support for the BMI160Simon Glass2018-01-121-0/+2
* grunt: Enable the CPU temperature sensorSimon Glass2018-01-122-0/+6
* grunt: rename volume GPIOsEdward Hill2018-01-122-4/+2
* grunt: Lowering I2C bus speed to 400kHz for TCPC chipsJett Rink2018-01-111-2/+2
* grunt: Add accel, gyro, and motion_sense task.Justin TerAvest2018-01-083-0/+178
* grunt: Use PPC for USB PDEdward Hill2017-12-134-118/+160
* grunt: Update battery infoEdward Hill2017-12-111-4/+4
* grunt: Add keyboard backlightBenjamin Gordon2017-12-113-0/+22
* grunt: Remove I2C pull upsEdward Hill2017-12-081-5/+5
* grunt: Add charger and SOC thermal sensorsJustin TerAvest2017-11-302-0/+62
* grunt: Initial USB PD board code.Edward Hill2017-11-305-45/+338
* grunt: Enable CONFIG_BRINGUP.Justin TerAvest2017-11-291-0/+2
* chipset: Introduce CHIPSET_STATE_ANY_SUSPENDFurquan Shaikh2017-11-281-1/+1
* buttons: Make buttons[] common.Aseda Aboagye2017-11-172-8/+4
* grunt: Initial GPIO setup for gruntEdward Hill2017-11-145-958/+169
* charge_manager: Enter safe mode at bootShawn Nematbakhsh2017-11-021-13/+0
* chg_ramp: Add charge_is_consuming_full_input_current().Aseda Aboagye2017-11-011-10/+0
* grunt: initial setup for ecYH Lin2017-10-118-0/+1767
View Lorry Controller Status