summaryrefslogtreecommitdiff
path: root/board/kunimitsu
Commit message (Expand)AuthorAgeFilesLines
* tcpm: update code to support multiple tcpm driverKevin K Wong2016-04-171-2/+3
* Kunimitsu: remove console commands for code sizeKyoung Kim2016-04-141-0/+2
* chell / kunimitsu / lars: Enable CONFIG_USB_PD_COMM_LOCKEDShawn Nematbakhsh2016-04-111-0/+1
* charge_manager: Report UNKNOWN USB charger for 2 seconds after changeShawn Nematbakhsh2016-04-031-1/+1
* sensor: update sensor driver to use I2C port from motion_sensor_tKevin K Wong2016-03-311-0/+3
* kunimitsu: remove CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5Kevin K Wong2016-03-111-1/+0
* Kunimitsu/Lars: correct adc voltage readingKyoung Kim2016-03-111-1/+8
* cleanup: Add warning comment to gpio.inc filesBill Richardson2016-02-252-0/+6
* GPIO: Move definitions of GPIO_KB_INPUT and OUTPUTAnton Staaf2016-02-222-3/+3
* Kunimitsu: Enable config REPLACE_LOADER_WITH_BSS_SLOWShobhit Srivastava2016-02-191-0/+1
* kunimitsu: hibernate: enable PseudoG3 support at board levelKevin K Wong2016-02-182-3/+17
* mec1322: clock: Use full-speed 48MHz processor clock during EC bootShawn Nematbakhsh2016-02-091-1/+1
* Kunimitsu: S0ix/S3 EC power improvementKyoung Kim2016-02-091-2/+2
* kunimitsu: reduce PD log sizeli feng2016-02-081-1/+1
* kunimitus: add VCONN swap abilityli feng2016-02-032-0/+10
* kunimitsu: lars: enable USB PD logging.Todd Broch2016-02-031-0/+2
* charger/Kunimitsu: Fix for boot from cut-off batteryVijay Hiremath2016-02-022-20/+39
* Kunimitsu: Change the battery minimum voltage valueVijay Hiremath2016-01-311-1/+1
* Kunimitsu: Fixing build error when enabled CONFIG_GYRO_L3GD20HAkshu Agrawal2016-01-281-1/+1
* chell/glados/kunimitsu/tlars: Enable temporary host storageDuncan Laurie2016-01-251-4/+13
* Kunimitsu: Fix leak on pin for battery_present.Kyoung Kim2016-01-223-6/+32
* Kunimitsu: Set the power button debounce time to zero in PMICShaunak Saha2016-01-201-0/+10
* glados / kunimitsu: led: battery LED blinking on low batteryli feng2016-01-151-2/+4
* Kunimitsu: Increase 5V rail in PMICKyoung Kim2016-01-141-0/+10
* Skylake: prevent EC from continuing execution after turning 3.3V_DSW off.Kyoung Kim2016-01-131-0/+2
* Kunimitsu/Lars: for PMIC, check i2c response before further initializationKyoung Kim2016-01-131-3/+10
* kunimitsu: increase stack size for PD_C0, PD_C1, and PD_CMDKevin K Wong2016-01-111-3/+3
* kunimitsu: add debug assert flagKevin K Wong2015-12-301-1/+0
* Kunimitsu: enable power threshold checking in power upli feng2015-12-161-0/+2
* pwm: Add common initialization for PWM pinsShawn Nematbakhsh2015-12-041-2/+2
* kunimitsu: modify charge LED gpio control to match FAB4 schematicli feng2015-12-032-4/+4
* common: adc/i2c: Mark task_waiting volatileShamile Khan2015-12-011-4/+0
* pd: send power change event to AP whenever input power is changedBen Lok2015-12-011-0/+5
* kunimitsu: Modify battery LED colourMike M Hsieh2015-11-301-12/+4
* kunimitsu: update accelerometer standard reference matrixVijay Hiremath2015-11-241-4/+4
* Kunimitsu: Add S0ix on SLP_S0 assertionKyoung Kim2015-11-192-2/+3
* kunimitsu: remove fab 3 related changesKevin K Wong2015-11-194-126/+6
* motion: Change units of ec_rate from us to ms.Gwendal Grignou2015-11-181-2/+2
* kunimitsu: Gyro is not used for lid calculationGwendal Grignou2015-11-181-3/+2
* kunimitsu: update for fab 4Kevin K Wong2015-11-173-20/+60
* GLaDOS: Kunimitsu: Enable link-time optimization.Aseda Aboagye2015-11-091-0/+1
* mec1322: adjust mec adc channels for analog reference of 3.0VAlec Berg2015-11-091-1/+1
* tcpm: Add configuration struct for tcpc i2c paramsShawn Nematbakhsh2015-11-081-0/+5
* chg: add narrow VDC power path supportRong Chang2015-11-051-0/+1
* mec1322: reduce system stack sizeli feng2015-11-041-1/+1
* led: correct LED blinking intervalli feng2015-11-041-4/+4
* cleanup: Standardize use of CONFIG_I2C and add MASTER/SLAVE CONFIGsShawn Nematbakhsh2015-11-031-0/+1
* mec1322: Remove CONFIG_PORT80_TASK_EN from boards.Aseda Aboagye2015-10-231-1/+0
* pd: change battery and variable sink cap for voltage inaccuracyAlec Berg2015-10-231-2/+2
* Kunimitsu: Add support to enable L3GD20H gyrometerVijay Hiremath2015-10-212-0/+46
View Lorry Controller Status