summaryrefslogtreecommitdiff
path: root/board/nocturne
Commit message (Expand)AuthorAgeFilesLines
* ss-mux: remove unused port_addr initializationv2.0.0Jett Rink2018-09-171-3/+0
* usb-c: add high priority tasks for interruptsJett Rink2018-09-171-1/+3
* base_detect: Expose console command to force state.RaviChandra Sadineni2018-09-132-2/+33
* type: Rename matrix_3x3_t to mat33_fp_tYilun Lin2018-09-131-1/+1
* nocturne: Use USBC alert signal for TCPC alert statusScott Collyer2018-08-311-10/+14
* nocturne: switch from tablet mode to base state reportingDmitry Torokhov2018-08-312-11/+4
* nocturne: Remove CONFIG_SYSTEM_UNLOCKED.stabilize-11005.BAseda Aboagye2018-08-251-3/+0
* nocturne: Enable CONFIG_I2C_BUS_MAY_BE_UNPOWEREDAseda Aboagye2018-08-222-0/+10
* nocturne: Turn on UHALL_PWR_EN by default.Aseda Aboagye2018-08-181-1/+1
* nocturne: Enable TCPC low power modePuthikorn Voravootivat2018-08-171-0/+2
* nocturne: Control UHALL_PWR_EN based on lid state.Aseda Aboagye2018-08-172-1/+13
* nocturne: Enable low power idlePuthikorn Voravootivat2018-08-171-0/+1
* nocturne: Add board_set_tcpc_power_mode().Aseda Aboagye2018-08-172-0/+12
* servo_v4: add per port dualrole settingNick Sanders2018-08-151-2/+2
* nocturne: Change RCAM_VSYNC to rising edge.Aseda Aboagye2018-08-151-1/+1
* nocturne: Flip board version reporting.Aseda Aboagye2018-08-151-5/+5
* nocturne: Update sensor active mask to include S3.Aseda Aboagye2018-08-101-3/+3
* nocturne: set default ALS calibrationPuthikorn Voravootivat2018-08-091-1/+2
* nocturne: Dynamically disable effect of SLP_S0# on all VRsPuthikorn Voravootivat2018-08-071-2/+87
* nocturne: Enable active discharge on V1.8A & V3.3AAseda Aboagye2018-08-031-0/+3
* nocturne: Set OTG pins on UFP for Port 0.Aseda Aboagye2018-07-311-1/+10
* nocturne: Tie batt disconnect state to DSG FET status.Aseda Aboagye2018-07-301-5/+4
* nocturne: Enable sensor IRQs in S0.Aseda Aboagye2018-07-261-0/+4
* nocturne: Enable DPTF support.Aseda Aboagye2018-07-251-0/+2
* nocturne: Restart base detection in S3.Aseda Aboagye2018-07-251-4/+4
* nocturne: Don't read gyro temp sensor in <= S5.Aseda Aboagye2018-07-191-1/+14
* nocturne: Adjust IMVP8 step decay quantization.Aseda Aboagye2018-07-181-0/+15
* nocturne: Add Gyro temperature sensor.Aseda Aboagye2018-07-182-0/+3
* nocturne: Reduce input current limit by 5%.Aseda Aboagye2018-07-171-3/+8
* nocturne: Set BMI160 speed to 400kHZGwendal Grignou2018-07-141-2/+1
* nocturne: Change FIFO settingsGwendal Grignou2018-07-141-1/+1
* nocturne: Add on-board temperature sensorsSumeet Pawnikar2018-06-282-0/+30
* nocturne: Remove internal pulls on PD interrupts.Aseda Aboagye2018-06-271-0/+13
* nocturne: Update LED settings.Aseda Aboagye2018-06-272-5/+11
* nocturne: Turn off sensor interrupts in S5.Aseda Aboagye2018-06-261-4/+21
* nocturne: Support new base USB fault protection IC.Aseda Aboagye2018-06-212-4/+18
* nocturne: Disable HC debug by defaultGwendal Grignou2018-06-211-0/+8
* nocturne: Fix BMI160 settingGwendal Grignou2018-06-151-5/+4
* nocturne: Fix CPU_PROCHOT polarity.Aseda Aboagye2018-06-082-1/+2
* Fizz: add CONFIG_BOARD_HAS_RTC_RESETRyan Zhang2018-06-071-1/+0
* nocturne: Change SYS_RST_L to open drain.Aseda Aboagye2018-06-071-1/+1
* nocturne: Add NVMe power enable controls.Aseda Aboagye2018-06-011-0/+8
* nocturne: Set V085A output voltage to 0.85V.Aseda Aboagye2018-05-311-0/+3
* nocturne: Add pull ups on PD INTs.Aseda Aboagye2018-05-291-2/+2
* nocturne: Fix PWM0 alternate pin definition.Aseda Aboagye2018-05-291-1/+1
* console_channel.inc: Add more ifdef to reduce number of channelsNicolas Boichat2018-05-261-1/+1
* ppc: making driver non-constJett Rink2018-05-241-2/+2
* espi: convert all eSPI board to use CONFIG_HOSTCMD_ESPIJett Rink2018-05-221-2/+1
* nocturne: Fix EC hibernate.Aseda Aboagye2018-05-222-2/+26
* nocturne: Power base on startup if attached.Aseda Aboagye2018-05-171-2/+8
View Lorry Controller Status