summaryrefslogtreecommitdiff
path: root/board/volteer/gpio.inc
Commit message (Expand)AuthorAgeFilesLines
* Volteer: Add support for FRS to C1Eric Herrmann2021-01-281-0/+1
* volteer: Configure additional unused signalsKeith Short2020-12-081-0/+4
* volteer: remove support for boards with board ID 0Keith Short2020-11-051-12/+4
* volteer: Fix spellingAbe Levkoy2020-10-231-1/+1
* volteer: Configure temperature sensor pinsAbe Levkoy2020-10-201-0/+4
* volteer: Configure unused GPIOsAbe Levkoy2020-10-141-0/+3
* BB retimer: Remove FORCE_PWR GPIO from EC driverVijay Hiremath2020-08-191-2/+0
* volteer: Reconfigure SSD GPIOsAbe Levkoy2020-08-071-4/+5
* volteer: Update GPIO namesAbe Levkoy2020-07-011-5/+5
* volteer: Configure unused GPIOs as inputsAbe Levkoy2020-07-011-0/+13
* volteer: Add GPIO M2_SSD_PLA and M2_SSD_PLNAbe Levkoy2020-06-271-1/+6
* volteer: Enable DSW_PWROK pass-throughAbe Levkoy2020-06-261-4/+3
* volteer: Add GPIO_USB_C1_RT_INT_ODLAbe Levkoy2020-06-261-0/+2
* volteer (board): Remove power sequencing supportAbe Levkoy2020-06-251-16/+0
* volteer: Remove DisplayPort HPD GPIOsAbe Levkoy2020-06-251-4/+0
* volteer: add USB-A power enable and disableKeith Short2020-06-151-0/+2
* volteer: remove VSYNC sensorstabilize-lazor-13278.B-masterKeith Short2020-06-091-1/+0
* volteer: add USB overcurrent notification to APKeith Short2020-06-051-0/+2
* volteer: set H1 packet mode GPIO lowKeith Short2020-05-091-7/+2
* volteer: Add board config for BMI260Ching-Kang Yen2020-04-241-0/+1
* icelake: Cleanup power sequencing for IceLake/TigerLake/JasperLakeKeith Short2020-04-091-0/+1
* Volteer: add monitoring for PROCHOT inputKeith Short2020-03-281-0/+1
* volteer: Update EC to AP interrupt assignmentKeith Short2020-02-271-1/+1
* volteer: Configure EC_VOLUP_BTN_ODL for next buildKeith Short2020-02-271-3/+9
* volteer: Update USB C1 reset for next buildstabilize-volteer-12931.B-masterKeith Short2020-02-261-3/+9
* volteer: add USB3 daughterboard supportstabilize-12881.B-masterCaveh Jalali2020-02-041-2/+2
* volteer: Enable low power modeKeith Short2020-01-281-1/+0
* volteer: add keyboard backlight supportKeith Short2020-01-111-0/+1
* volteer: enable tablet mode supportKeith Short2020-01-091-0/+1
* volteer: Enable daughter-board LEDAbe Levkoy2020-01-081-5/+5
* volteer: add motionsense supportKeith Short2020-01-071-0/+2
* volteer: add support for volume up/down buttonsKeith Short2019-12-111-0/+2
* volteer: Enable BC1.2 charge rampVijay Hiremath2019-12-071-0/+3
* volteer: Enable Burnisde Bridge retimerVijay Hiremath2019-12-071-0/+7
* volteer: Keep RSMRST# pin low at initVijay Hiremath2019-12-061-1/+1
* volteer: Enable USB-C Port 1Vijay Hiremath2019-12-041-0/+3
* volteer: enable thermal managementKeith Short2019-12-041-2/+5
* volteer: enable EC controlled fanKeith Short2019-11-211-0/+2
* volteer: Add USB-C policyVijay Hiremath2019-11-211-0/+4
* volteer: enable eDP backlightKeith Short2019-11-151-0/+7
* Volteer: configure USBC port 0Keith Short2019-11-121-0/+3
* volteer: add initial battery supportKeith Short2019-11-091-0/+3
* volteer: Add manual power sequencingKeith Short2019-11-011-1/+18
* tigerlake/icelake: add support for SYS_PWROKKeith Short2019-11-011-1/+2
* eSPI: Configure SLP_S3, SLP_S4 separatelyAbe Levkoy2019-10-301-4/+1
* volteer: Remove ISR todoAbe Levkoy2019-10-281-1/+0
* volteer: Add GPIO_LOCKED to EC_RST_ODL PSL inputKeith Short2019-10-231-1/+6
* volteer: Configure power sequencing signalsAbe Levkoy2019-10-171-0/+17
* Volteer: fix I2C bus 0Keith Short2019-10-081-1/+1
* volteer: Configure GPIOs connected to keyboardAbe Levkoy2019-10-051-0/+10
View Lorry Controller Status