summaryrefslogtreecommitdiff
path: root/board/volteer
Commit message (Expand)AuthorAgeFilesLines
* volteer: Update EC to AP interrupt assignmentKeith Short2020-02-271-1/+1
* volteer: Configure EC_VOLUP_BTN_ODL for next buildKeith Short2020-02-271-3/+9
* volteer: Update USB C1 reset for next buildstabilize-volteer-12931.B-masterKeith Short2020-02-261-3/+9
* volteer: add USB3 daughterboard supportstabilize-12881.B-masterCaveh Jalali2020-02-041-2/+2
* volteer: Enable low power modeKeith Short2020-01-281-1/+0
* Volteer: move USB product ID to baseboardstabilize-12859.B-masterKeith Short2020-01-241-8/+0
* TBT/USB4: Allow enabling TBT & USB4 per port basedVijay Hiremath2020-01-151-0/+11
* TBT: Allow limiting the cable speed based on board designVijay Hiremath2020-01-151-0/+15
* volteer: add keyboard backlight supportKeith Short2020-01-111-0/+1
* volteer: enable tablet mode supportKeith Short2020-01-093-0/+3
* volteer: Enable daughter-board LEDAbe Levkoy2020-01-081-5/+5
* volteer: add motionsense supportKeith Short2020-01-074-1/+8
* volteer: add support for volume up/down buttonsKeith Short2019-12-113-1/+5
* volteer: update battery parameterScott Chao2019-12-091-5/+5
* volteer: Enable BC1.2 charge rampVijay Hiremath2019-12-072-19/+23
* volteer: Enable Burnisde Bridge retimerVijay Hiremath2019-12-071-0/+7
* volteer: Keep RSMRST# pin low at initVijay Hiremath2019-12-061-1/+1
* volteer: Enable USB-C Port 1Vijay Hiremath2019-12-043-1/+9
* volteer: enable thermal managementKeith Short2019-12-041-2/+5
* volteer: disable CONFIG_BRINGUPKeith Short2019-11-211-6/+0
* volteer: enable EC controlled fanKeith Short2019-11-211-0/+2
* volteer: Add USB-C policyVijay Hiremath2019-11-212-0/+12
* volteer: enable eDP backlightKeith Short2019-11-151-0/+7
* volteer: add BC1.2 for USBC port 0Keith Short2019-11-121-0/+1
* Volteer: configure USBC port 0Keith Short2019-11-123-1/+15
* volteer: add charger supportKeith Short2019-11-101-0/+1
* volteer: add initial battery supportKeith Short2019-11-094-0/+77
* volteer: Configure ADC channelsKeith Short2019-11-081-3/+0
* volteer: Add manual power sequencingKeith Short2019-11-014-1/+220
* tigerlake/icelake: add support for SYS_PWROKKeith Short2019-11-011-1/+2
* eSPI: Configure SLP_S3, SLP_S4 separatelyAbe Levkoy2019-10-302-5/+1
* volteer: Remove ISR todoAbe Levkoy2019-10-281-1/+0
* volteer: Add GPIO_LOCKED to EC_RST_ODL PSL inputKeith Short2019-10-231-1/+6
* volteer: Configure power sequencing signalsAbe Levkoy2019-10-174-0/+26
* cometlake: Cleanup GPIO_PCH_SYS_PWROKKeith Short2019-10-151-0/+1
* volteer: Support keyboardAbe Levkoy2019-10-111-1/+3
* volteer: enable CONFIG_BRINGUPKeith Short2019-10-111-0/+6
* Volteer: fix I2C bus 0Keith Short2019-10-081-1/+1
* volteer: Configure GPIOs connected to keyboardAbe Levkoy2019-10-052-0/+11
* volteer: Configure the GPIOs connected to LEDsAbe Levkoy2019-10-021-0/+6
* volteer: Add RTC resetKeith Short2019-09-292-1/+2
* volteer: Configure the GPIOs connected to the AP/PCHKeith Short2019-09-272-6/+27
* Volteer: add I2C bus configurationKeith Short2019-08-201-0/+22
* Volteer: Add initial AP signalsKeith Short2019-08-204-2/+16
* Volteer: initial EC board setupKeith Short2019-08-205-0/+144
View Lorry Controller Status