summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* CR50: Fix ECC key generation to match the code used in factoryMeng-Huan Yu2018-11-221-15/+27
* Ampton: Correct accel sensor base reference dependent on sensor locationJames_Chao2018-11-211-8/+6
* liara: Use CONFIG_LED_PWM_CHARGE_STATE_ONLYEdward Hill2018-11-211-1/+1
* atlas_ish: remove HostCommand task related.Kyoung Kim2018-11-211-3/+1
* Servo v4: reduce RO flash sizeDiana Z2018-11-202-2/+8
* ocotpus: move VBUS_ADC config to baseJett Rink2018-11-1910-61/+11
* Fizz: Set initial fan speed to 50%Daisuke Nojiri2018-11-191-0/+2
* Fizz: Add Jax supportDaisuke Nojiri2018-11-192-19/+26
* Ampton: enable the interrupt for GPIO_BASE_SIXAXIS_INT_LJames_Chao2018-11-192-1/+7
* kukui: Fix shipping mode VSYS leakage.Yilun Lin2018-11-191-1/+7
* cr50: Add board strapping options for Sarien/ArcadaKeith Short2018-11-162-8/+47
* Liara: Add LGC batteryEdward Hill2018-11-162-0/+32
* phaser: update gpio based on next revJett Rink2018-11-162-11/+21
* Nami: Supply power up to 3A + 1.5ADaisuke Nojiri2018-11-161-0/+1
* meep: set PD on unused interruptJett Rink2018-11-161-8/+5
* fleex: set PD on unused interruptJett Rink2018-11-161-8/+5
* phaser: set PD on unused interruptJett Rink2018-11-161-8/+5
* bobba: add PD to unused lines to prevent floatJett Rink2018-11-161-11/+11
* Meep: update EC GPIOs for board version 1Diana Z2018-11-152-13/+20
* Nami: Apply full factor to full capacityDaisuke Nojiri2018-11-151-0/+2
* atlas: clean up ROP PMIC registersCaveh Jalali2018-11-151-17/+28
* Ampton: add sku id for convertible skuJames_Chao2018-11-151-2/+3
* cheza: Enable CONFIG_HOSTCMD_AP_RESET for debug usageWai-Hong Tam2018-11-151-0/+1
* eve: Enable support for multi-profile DPTFFurquan Shaikh2018-11-152-1/+11
* soraka: Enable multi-profile DPTFFurquan Shaikh2018-11-152-0/+10
* nautilus: Enable multi-profile DPTFFurquan Shaikh2018-11-151-0/+2
* usb-c: use higher priority task for interruptsJett Rink2018-11-1416-102/+134
* SN5S330: treat interrupts as level-sensitiveDiana Z2018-11-132-0/+16
* Delan: LED PWM Channel Changekoko2018-11-131-2/+2
* touchpad_st: update logical maximum of y valueWei-Han Chen2018-11-081-1/+1
* Nami: Use display battery percentage to control LEDDaisuke Nojiri2018-11-081-20/+27
* Jerry: Remove keyboard console commandDaisuke Nojiri2018-11-081-0/+1
* cheza: Make USB mux handled by TCPC chips and HPD handled by APWai-Hong Tam2018-11-072-4/+83
* cheza: Apply the fix to handle two or more HPD eventsWai-Hong Tam2018-11-071-5/+0
* cheza: Don't mux the DP lines until HPD level goes highWai-Hong Tam2018-11-071-10/+10
* Project Delan: Update Battery Parametersamsp_liu2018-11-072-18/+75
* Liara: Update LED behaviorJosh Tsai2018-11-071-5/+2
* Cr50: Add valid PCR value for pinweaverIgor2018-11-071-0/+23
* kukui: Enable TCPC low power mode.Yilun Lin2018-11-071-0/+1
* Apel: add battery configurationJames_Chao2018-11-072-0/+28
* bobba: enable sensors sync via dedicated IRQ pinEnrico Granata2018-11-072-3/+2
* cr50: enable ITE CCD programmingVadim Bendebury2018-11-053-0/+69
* cheza: Correct the PSYS ADC multiplierWai-Hong Tam2018-11-021-3/+3
* Kalista: Modify gpio settingsTino Liu2018-11-021-8/+13
* cr50: Rename tpm_nvmem_read to tpm_nvmem_opsLouis Collard2018-11-024-6/+6
* kukui: Enable gauge_interrupt.Yilun Lin2018-11-013-4/+31
* Bobba: Modify base accel/gyro rotation for SKU with AR Cam.Tino Liu2018-11-011-0/+28
* rammus: Correct accel sensor BMI160 base reference dependent on sensor location.michael_chen2018-10-311-2/+2
* meep: fix sensor data and accel orientationDevin Lu2018-10-311-5/+11
* meep: enable keyboard factory scanningDevin Lu2018-10-312-0/+25
View Lorry Controller Status