summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* Nami: Apply full factor to full capacityDaisuke Nojiri2018-11-151-0/+2
* atlas: clean up ROP PMIC registersCaveh Jalali2018-11-151-17/+28
* Ampton: add sku id for convertible skuJames_Chao2018-11-151-2/+3
* cheza: Enable CONFIG_HOSTCMD_AP_RESET for debug usageWai-Hong Tam2018-11-151-0/+1
* eve: Enable support for multi-profile DPTFFurquan Shaikh2018-11-152-1/+11
* soraka: Enable multi-profile DPTFFurquan Shaikh2018-11-152-0/+10
* nautilus: Enable multi-profile DPTFFurquan Shaikh2018-11-151-0/+2
* usb-c: use higher priority task for interruptsJett Rink2018-11-1416-102/+134
* SN5S330: treat interrupts as level-sensitiveDiana Z2018-11-132-0/+16
* Delan: LED PWM Channel Changekoko2018-11-131-2/+2
* touchpad_st: update logical maximum of y valueWei-Han Chen2018-11-081-1/+1
* Nami: Use display battery percentage to control LEDDaisuke Nojiri2018-11-081-20/+27
* Jerry: Remove keyboard console commandDaisuke Nojiri2018-11-081-0/+1
* cheza: Make USB mux handled by TCPC chips and HPD handled by APWai-Hong Tam2018-11-072-4/+83
* cheza: Apply the fix to handle two or more HPD eventsWai-Hong Tam2018-11-071-5/+0
* cheza: Don't mux the DP lines until HPD level goes highWai-Hong Tam2018-11-071-10/+10
* Project Delan: Update Battery Parametersamsp_liu2018-11-072-18/+75
* Liara: Update LED behaviorJosh Tsai2018-11-071-5/+2
* Cr50: Add valid PCR value for pinweaverIgor2018-11-071-0/+23
* kukui: Enable TCPC low power mode.Yilun Lin2018-11-071-0/+1
* Apel: add battery configurationJames_Chao2018-11-072-0/+28
* bobba: enable sensors sync via dedicated IRQ pinEnrico Granata2018-11-072-3/+2
* cr50: enable ITE CCD programmingVadim Bendebury2018-11-053-0/+69
* cheza: Correct the PSYS ADC multiplierWai-Hong Tam2018-11-021-3/+3
* Kalista: Modify gpio settingsTino Liu2018-11-021-8/+13
* cr50: Rename tpm_nvmem_read to tpm_nvmem_opsLouis Collard2018-11-024-6/+6
* kukui: Enable gauge_interrupt.Yilun Lin2018-11-013-4/+31
* Bobba: Modify base accel/gyro rotation for SKU with AR Cam.Tino Liu2018-11-011-0/+28
* rammus: Correct accel sensor BMI160 base reference dependent on sensor location.michael_chen2018-10-311-2/+2
* meep: fix sensor data and accel orientationDevin Lu2018-10-311-5/+11
* meep: enable keyboard factory scanningDevin Lu2018-10-312-0/+25
* Ampton: add initial motion sensor codeDiana Z2018-10-313-3/+183
* Nami: Add keymasks for page-up/down, home, end, deleteDaisuke Nojiri2018-10-311-21/+24
* cheza: Remove the internal PU for UART pinsWai-Hong Tam2018-10-311-1/+1
* cheza: Update battery infoWai-Hong Tam2018-10-311-3/+2
* cheza: Add internal PU for GPIO USB_C1_OC_ODLWai-Hong Tam2018-10-311-1/+1
* Delan: LED Color Changekoko2018-10-313-14/+14
* cheza: Configure GPIO RCAM_VSYNC to operate at 1.8VWai-Hong Tam2018-10-311-1/+1
* cheza: Remove the unnecessary GPIO_SEL_1P8V flagsWai-Hong Tam2018-10-311-5/+5
* kukui/emmc: Share EXTI15 interrupt between SPI and eMMCNicolas Boichat2018-10-302-33/+48
* octopus: update active_mask for consistencyJett Rink2018-10-304-13/+13
* Kalista: Update baseboard directoryDaisuke Nojiri2018-10-301-11/+1
* dptf: Get rid of CONFIG_DPTF_DEVICE_ORIENTATIONFurquan Shaikh2018-10-309-9/+0
* Liara: Update battery manufacture nameRuby Lee2018-10-301-3/+3
* cheza: Monitor the WARM_RESET_L signal to hold APWai-Hong Tam2018-10-303-4/+13
* kukui: Enable CONFIG_CMD_AP_RESET_LOGNicolas Boichat2018-10-291-0/+1
* delan: Use CBI EEPROM for board version and SKU IDEdward Hill2018-10-281-0/+7
* Kalista: Create baseboard directoryDaisuke Nojiri2018-10-275-0/+209
* Add nami_fp configurationNicolas Norvez2018-10-261-0/+1
* atlas_ish: initial board files for atlas_ishli feng2018-10-265-0/+162
View Lorry Controller Status