summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* Fizz: Add GPIOs used for CECStefan Adolfsson2018-05-102-0/+7
* phaser: initial files commitJett Rink2018-05-097-0/+367
* tablet_mode: Define common interrupt handler for tablet switchDaisuke Nojiri2018-05-093-1/+4
* Nami: Use lid angle to detect tablet mode for Vayne & NamiDaisuke Nojiri2018-05-091-19/+13
* cheza: Remove BC1.2 switch hackTom Wai-Hong Tam2018-05-091-14/+0
* cheza: Support PD and chargingTom Wai-Hong Tam2018-05-097-12/+876
* cheza: Change ACOK_OD pin to EC inputTom Wai-Hong Tam2018-05-081-5/+5
* cheza: Lower the I2C bus speed of smart batteryTom Wai-Hong Tam2018-05-081-1/+1
* cheza: Remove internal pull-up for the BATT_PRES_ODL pinTom Wai-Hong Tam2018-05-081-1/+1
* yorp: renegotiate Vbus down before hibernatingJett Rink2018-05-081-21/+0
* cheza: Support confirmation of power lostTom Wai-Hong Tam2018-05-081-1/+1
* cheza: Enable AP_RST_REQ as a request from AP to reset itselfWai-Hong Tam2018-05-082-1/+2
* meowth_fp: make FP_RST_ODL push-pullVincent Palatin2018-05-081-1/+1
* atlas: config PROCHOT GPIO as inputCaveh Jalali2018-05-081-1/+1
* cr50: disable s3_terms during initMary Ruthven2018-05-071-4/+28
* Nami: Disable ALS for AkaliTino Liu2018-05-071-2/+3
* yorp: Configure GPIO_HIB_WAKE_HIGH for AC_PRESENTFurquan Shaikh2018-05-071-2/+4
* yorp: Enable SINK_CTRL on PPC before hibernatingFurquan Shaikh2018-05-071-1/+9
* yorp: Shutdown AP when doing hibernateFurquan Shaikh2018-05-041-0/+12
* eve: Limit data role swap to port 0Duncan Laurie2018-05-041-0/+4
* cheza: Make sure switchcap is configured rightAlexandru M Stan2018-05-042-0/+12
* cheza: Add SDM845 power sequence for rev-0 boardWai-Hong Tam2018-05-044-2/+35
* octopus: move more implementation to baseboardJett Rink2018-05-044-307/+4
* octopus: remove pwm code for LEDsJett Rink2018-05-042-6/+0
* yorp: Add support for SONY batteryDivya Sasidharan2018-05-042-0/+29
* nocturne: Only power base when AP is on.Aseda Aboagye2018-05-031-16/+46
* yorp: Control backlight based on chipset transitionsFurquan Shaikh2018-05-022-0/+13
* octopus: move common function to baseboardJett Rink2018-05-022-144/+0
* octopus: move common CONFIG defines into baseboardJett Rink2018-05-022-282/+11
* bip: adding missing common definesJett Rink2018-05-021-0/+3
* bip: add keyboard functionalityJett Rink2018-05-023-0/+26
* yorp: enable low power mode on ECJett Rink2018-05-021-0/+2
* nautilus: Move PMIC init to a deferred functionFurquan Shaikh2018-05-011-1/+4
* nautilus: Enable usb device modeFurquan Shaikh2018-05-011-1/+8
* anx7447: convert automatic OCM erase into commandJett Rink2018-05-012-2/+2
* bip: add correct charger driverJett Rink2018-05-011-2/+1
* board: Add initial nocturne support.Aseda Aboagye2018-05-019-0/+1752
* cr50: make fallback certs a compile time optionVadim Bendebury2018-04-281-18/+39
* Nami: Add host command handler for keyboard backlight controlDaisuke Nojiri2018-04-271-0/+27
* Nami: Add keyboard backlight controlDaisuke Nojiri2018-04-275-13/+134
* cr50: use new function to verify index presenceVadim Bendebury2018-04-271-3/+3
* grunt: Increase CONFIG_EXTPOWER_DEBOUNCE_MS to 200Edward Hill2018-04-271-0/+6
* grunt: Drop the unnecessary charge-current limitSimon Glass2018-04-271-8/+0
* npcx: change chip variants of npcx7 series for better clarification.Mulin Chao2018-04-274-9/+9
* Cr50: Add logging functionality to PinWeaver.Allen Webb2018-04-273-6/+8
* Cr50: Added Pinweaver base implementation.Allen Webb2018-04-274-0/+86
* octopus: move common usb/battery code into baseboardJett Rink2018-04-269-1147/+111
* cheza: Increase charger current to maxAlexandru M Stan2018-04-261-0/+7
* poppy: Enable usb device modeFurquan Shaikh2018-04-263-3/+9
* yorp: lower i2c speeds to 100kHzJett Rink2018-04-261-2/+2
View Lorry Controller Status