summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* nightfury : Enable PWM and Tach for FanYongBeum.Ha2020-04-022-3/+5
* EFS2: Enable Early Firmware Selection V2 for Puffdnojiri2020-04-022-39/+2
* Lazor: Initial commit for Lazor boardWai-Hong Tam2020-04-027-0/+962
* nightfury: fix new lid accel orientation and odr configInno.Park2020-04-011-4/+4
* dalboz: use physical pin to generate SCI to SOCPaul Ma2020-04-012-0/+4
* nightfury : remove ambient thermal sensorYongBeum.Ha2020-04-012-15/+6
* nightfury: Enable fanYongBeum.Ha2020-04-013-2/+59
* Pantheon: Make precharge current conform to the specdnojiri2020-03-311-1/+1
* Ezkinil: Fix rotation matrices of base/lid accel configDavid Huang2020-03-311-3/+15
* trembyle: LED_FULL is blue, not greenEdward Hill2020-03-311-15/+15
* dratini: change thermal configuration for PVTDevin Lu2020-03-311-1/+1
* kakadu: update led behaviorScott Chao2020-03-311-4/+4
* Trogdor: Create Trogdor baseboardWai-Hong Tam2020-03-304-512/+4
* damu: reduce bitbang failrateScott Chao2020-03-302-3/+3
* damu: modify gpio as SPI for BMI160.Scott Chao2020-03-302-13/+24
* Zork: Clean up FW_CONFIG hook functionsEdward Hill2020-03-284-57/+82
* Morphius/Ezkinil: Remove Trembyle V0 HW support.Edward Hill2020-03-286-48/+4
* Volteer: add monitoring for PROCHOT inputKeith Short2020-03-284-0/+4
* nightfury: enable lid accelerometer lis2ds12Inno.Park2020-03-272-11/+13
* Mushu : Base G-sensor configloganliao2020-03-271-2/+2
* nucleo-h743zi: Enable blink exampleCraig Hesling2020-03-271-0/+6
* dedede: Make EC_MKBP_INT_L open drainAseda Aboagye2020-03-262-2/+2
* malefor: Add lid and base accel sensorsxiong.huang2020-03-265-202/+144
* damu: enable bit-bang for battery smbusScott Chao2020-03-264-1/+16
* Ezkinil: Add FSUSB42UMX driverDavid Huang2020-03-262-1/+37
* Ezkinil: Add control USB_A1_RETIMER_EN during power on/offDavid Huang2020-03-261-0/+12
* Ezkinil: Add redriver TUSB544 and PS8743 for EzkinilDavid Huang2020-03-262-3/+38
* malefor: move sensors support from baseboard to boardxiong.huang2020-03-269-0/+618
* cleanup: drop the _TYPEC part of USB device configJett Rink2020-03-263-3/+3
* nightfury: Enable base light sensorJongpil Jung2020-03-262-13/+18
* USB: Make handling of CC overvoltage independent of PPCsDiana Z2020-03-261-1/+1
* Waddledee: Configure DAC for PSYSDiana Z2020-03-261-1/+2
* dratini: Reduce input voltage to 5V when battery fullDevin Lu2020-03-251-1/+28
* nightfury : change BC1.2 IC to Pericom 9201YongBeum.Ha2020-03-252-13/+12
* asurada: board.h: add more section headingsTing Shen2020-03-251-9/+12
* dalboz: Remove CONFIG_BRINGUPLu Zhang2020-03-241-1/+0
* Waddledee: Fill in batteriesDiana Z2020-03-242-3/+300
* Waddledee: Complete basic EC tasksDiana Z2020-03-246-47/+179
* bloonchipper: Reorganize board.h into sectionsCraig Hesling2020-03-241-70/+117
* bloonchipper: More clearly disable UART DMACraig Hesling2020-03-241-5/+5
* nucleo-f412zg: Initial board offeringCraig Hesling2020-03-249-0/+251
* stm32f412: Fix chip config Flash and RAM sizesCraig Hesling2020-03-241-5/+0
* nightfury: remove lid als/rgb sensor and camera syncJongpil Jung2020-03-243-119/+2
* kappa: fix battery manufacturer name dataDevin Lu2020-03-241-1/+1
* Mushu : add dual fan control by ECloganliao2020-03-233-1/+65
* halvor: Initial EC imageFrank Wu2020-03-207-0/+645
* dalboz: Set IOEX interrupt handler for DB optionEdward Hill2020-03-202-2/+25
* dalboz: Set usb_port_enable[] for DB optionEdward Hill2020-03-201-0/+2
* dalboz: select GPIOs based on DB optionEdward Hill2020-03-203-7/+55
* zork: split ioex_config[] to trembyle and dalbozEdward Hill2020-03-201-21/+21
View Lorry Controller Status