summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* nocturne: Set BMI160 speed to 400kHZGwendal Grignou2018-07-141-2/+1
* nocturne: Change FIFO settingsGwendal Grignou2018-07-141-1/+1
* grunt, careena: Clean up GPIO alternate functions.Jonathan Brandmeyer2018-07-132-26/+26
* Grunt: Elide obsolete GPIO configuration.Jonathan Brandmeyer2018-07-131-1/+0
* DragonEgg: enable EC UARTDino Li2018-07-131-0/+1
* Nami: Toggle power of PS8713B on suspend/resumeDaisuke Nojiri2018-07-122-1/+3
* yorp: Change LED blink timingVenkateswarlu Vinjamuri2018-07-111-2/+2
* DragonEgg: Change CHIP_VARIANT to it8320dxDino Li2018-07-111-1/+1
* kukui: emulate eMMC boot mode using SPI controller.Nicolas Boichat2018-07-116-3/+333
* DragonEgg: Add misc pins section to gpio.incScott Collyer2018-07-111-26/+56
* yorp: Enable tablet modeFurquan Shaikh2018-07-111-0/+3
* phaser: Enable EC_RST_ODL as wake source from PSL hibernate modeFurquan Shaikh2018-07-111-4/+24
* kukui: Add LED behavior.Yilun Lin2018-07-111-4/+62
* Nami: Enable temperature contorl by fanDaisuke Nojiri2018-07-102-4/+99
* phaser: Enable PSLFurquan Shaikh2018-07-102-0/+8
* meowth_fp: flash_fp_mpu: Make sure WP is deassertedNicolas Boichat2018-07-091-0/+5
* flash_fp_mcu: Unlock flash before programming itNicolas Boichat2018-07-061-1/+2
* npcx: uart: Add driver support for the second UARTCHLin2018-07-052-1/+16
* phaser: enable lid angle tablet modePaul Ma2018-07-052-0/+7
* meowth_fp: Update SPIID for nocturneNicolas Boichat2018-07-051-3/+6
* phaser: Enable DPTF and orientationJustin TerAvest2018-07-041-0/+3
* yorp: Enable DPTFJustin TerAvest2018-07-041-0/+2
* whiskers touchpad: adjust value rangeWei-Han Chen2018-07-041-2/+2
* DragonEgg: Add I2C pins/alt functions and config tableScott Collyer2018-07-031-0/+20
* bip: comment fix to clarify GPIO pinsDiana Z2018-07-031-2/+2
* kukui: GPIO fixups, and mirror AP watchdog input to outputNicolas Boichat2018-07-032-8/+13
* bobba: initial files commitJustin TerAvest2018-07-028-0/+755
* board: it83xx based boards start to use CHIP_FAMILY and CHIP_VARIANTDino Li2018-07-025-0/+10
* kukui: Initial setup for ec.Yilun Lin2018-06-308-0/+1316
* phaser: add new lis2de chip typePaul Ma2018-06-301-2/+3
* atlas: enable ALS pollingCaveh Jalali2018-06-291-0/+3
* Nami: configure motion sensors for board variants earlyDaisuke Nojiri2018-06-291-14/+14
* Nami: Add fan configurations for Sona and PantheonDaisuke Nojiri2018-06-291-2/+30
* phaser: add internal PUs for unused pins to prevent leakage current.Mulin Chao2018-06-291-0/+7
* nocturne_fp: [HACK] Disable STOP mode by defaultVincent Palatin2018-06-291-0/+4
* phaser: enable tablet mode and lid anglestabilize-nocturne.10828.BPaul Ma2018-06-293-6/+54
* yorp: add internal PUs for unused pins to prevent leakage current.Mulin Chao2018-06-281-0/+7
* Nami: Support battery_check_disconnect for TI and Renesas gaugeDaisuke Nojiri2018-06-281-4/+71
* careena, grunt: Enable pullup for the lid switch.Jonathan Brandmeyer2018-06-282-2/+2
* bip: implement charging LEDDiana Z2018-06-284-2/+75
* nocturne_fp: update flash_fp_mcu for the new power controlVincent Palatin2018-06-281-4/+15
* nocturne: Add on-board temperature sensorsSumeet Pawnikar2018-06-282-0/+30
* Nami: Set GPIO42 to high Z for older boardsDaisuke Nojiri2018-06-271-0/+4
* phaser: fix lis2de resolution and sensor value outputPaul Ma2018-06-271-1/+1
* DragonEgg: Initial skeleton for DragonEggScott Collyer2018-06-275-0/+144
* nocturne: Remove internal pulls on PD interrupts.Aseda Aboagye2018-06-271-0/+13
* Nami: Lock ECDaisuke Nojiri2018-06-271-6/+1
* nocturne: Update LED settings.Aseda Aboagye2018-06-272-5/+11
* wheatley: remove wheatley board driver since running out of code space.Mulin Chao2018-06-278-1738/+0
* phaser: Add volume buttons.nickchen2018-06-273-0/+7
View Lorry Controller Status