summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* it8380dev: add pwm control moduleDino Li2014-10-293-21/+51
* twinkie: dual channel CCx sniffingstabilize-6412.BVincent Palatin2014-10-283-69/+111
* samus: use resulting current limit from charge managerAlec Berg2014-10-283-72/+77
* charge_manager: Move supplier list and priority hierarchy to boardShawn Nematbakhsh2014-10-263-1/+20
* pd: for DP mode, only enter mode if device is DFP_U capableAlec Berg2014-10-252-4/+16
* Add initial support for jerryKatie Roberts-Hoffman2014-10-258-0/+448
* pd: Add DFP parsing for alternate mode status & attention.Todd Broch2014-10-254-49/+92
* ryu: Enable watchdog helper for P2 boardsVic Yang2014-10-241-1/+2
* pd: update DP pin configuration declarationVincent Palatin2014-10-242-4/+4
* pd: update DP mode signaling bitsVincent Palatin2014-10-244-6/+4
* ryu: properly enable UART Rx DMA for P2 boardsVic Yang2014-10-241-0/+1
* ryu: Enable pull-up on console UART Tx/Rx pinsVic Yang2014-10-232-13/+13
* plankton: Fix output voltage selectionVic Yang2014-10-231-2/+2
* ryu: Implement battery cut-offVic Yang2014-10-238-46/+80
* discovery-stm32f072: Enable SPI over USB tunnelAnton Staaf2014-10-235-19/+80
* Allow 5V/3A on PlanktonVic Yang2014-10-221-3/+4
* ryu_p2: Fix broken build due to overlapped commitsBill Richardson2014-10-221-11/+15
* samus_pd: Add BC1.2 charging and charge port + current limit selectionShawn Nematbakhsh2014-10-225-11/+163
* ryu: enable lid switchVic Yang2014-10-226-16/+6
* samus: change fan RPM values, enable fast-startBill Richardson2014-10-221-6/+6
* usb_pd_protocol: Add support for charge_manager and voltage reportingShawn Nematbakhsh2014-10-229-33/+71
* ryu_p2: Set alternate function for USB D+/D- pinsVic Yang2014-10-221-0/+1
* ryu: enable lightbar on P2 boardsVic Yang2014-10-222-1/+3
* Add new build target ryu_p2 for Ryu P2 boardsVic Yang2014-10-228-0/+768
* samus: new algorithm for tmp006 object temperatureBill Richardson2014-10-221-0/+1
* samus: change hibernate delay to 7 daysAlec Berg2014-10-211-0/+4
* pd: Add DisplayPort status and configure SVDMs.Todd Broch2014-10-214-24/+151
* pd: Correct use of console printing in USB PD policy files.Todd Broch2014-10-219-52/+62
* pd: allow selection of Tx timer channelVic Yang2014-10-219-9/+28
* pd: alternate mode: Limit response to valid modes during discovery.Todd Broch2014-10-202-10/+10
* pd: alternate mode: simplify mode entry choice.Todd Broch2014-10-202-36/+2
* Twinkie: update sniffer codeVincent Palatin2014-10-201-49/+50
* Extend INA231 driver to support INA219 on PlanktonVic Yang2014-10-183-3/+7
* samus: add tap for batteryAlec Berg2014-10-183-1/+337
* plankton: Implement cable flipVic Yang2014-10-186-72/+173
* samus: Wait for VCORE_PGOOD before asserting SYS_PWROKDuncan Laurie2014-10-181-8/+25
* zinger: enable hibernateAlec Berg2014-10-171-1/+1
* hoho: Disable spi master by default.Todd Broch2014-10-161-1/+3
* hoho: correct CONFIG1 GPIO direction.Todd Broch2014-10-161-1/+1
* samus_pd: Initial DFP_D HPD GPIOs.Todd Broch2014-10-151-0/+2
* discovery-stm32f072: fix USB version stringAnton Staaf2014-10-151-1/+1
* zinger: fix double ADC interrupt bugAlec Berg2014-10-151-0/+3
* ryu: plankton: Increase PD task stack sizeVic Yang2014-10-152-2/+2
* samus: display battery status on lightbar on AC changeAlec Berg2014-10-151-0/+10
* dingdong: Add USB Billboard class device.Todd Broch2014-10-152-0/+97
* pd: samus: ryu: add back in Vconn support correctlyAlec Berg2014-10-158-6/+34
* pd: hoho: de-assert PD_SBU_ENABLE at boot.Todd Broch2014-10-141-1/+1
* samus: Add define for EVT3Duncan Laurie2014-10-141-0/+1
* samus: Change 3.3DSW_GATED to enabled in S0 and disabled in S3Duncan Laurie2014-10-141-4/+6
* ryu: Disable pull-up on AP_IN_SUSPENDVic Yang2014-10-141-1/+1
View Lorry Controller Status