summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* Jinlon: Choose a keyboard layout even for bad SKU IDRajat Jain2020-05-061-2/+3
* nocturne: Enable TCPMv2Patryk Duda2020-05-051-2/+10
* nocturne: Set ps8xxx as TCPC driver instead of generic tcpciPatryk Duda2020-05-051-2/+2
* CHERRY-PICK: nocturne: MKBP_WAKE_MASK: Set switch event as wake mask.Ravi Chandra Sadineni2020-05-051-1/+1
* CHERRY-PICK: nocturne: Use avg pin value for disconnection.Aseda Aboagye2020-05-051-12/+78
* CHERRY-PICK: Nocturne: Remove VR decay for V1.00A power railRoy Mingi Park2020-05-051-18/+0
* CHERRY-PICK: nocturne: Add internal pull-ups to unused strap pinsDivya Sasidharan2020-05-051-0/+4
* CHERRY-PICK: nocturne : Add logging for base detect voltages.Aseda Aboagye2020-05-051-0/+4
* CHERRY-PICK: nocturne: Add internal pull-downs to unused NVME pinsRoy Mingi Park2020-05-052-11/+3
* CHERRY-PICK: nocturne: Set I2C5 to 1.8V if possible.Puthikorn Voravootivat2020-05-051-3/+3
* CHERRY-PICK: nocturne: Enable CONFIG_THROTTLE_APPuthikorn Voravootivat2020-05-052-0/+18
* CHERRY-PICK: nocturne: Enable CONFIG_CHARGER_PROFILE_OVERRIDE.Aseda Aboagye2020-05-052-0/+61
* CHERRY-PICK: nocturne: Update LED settings (again).Aseda Aboagye2020-05-052-7/+56
* CHERRY-PICK: nocturne: Set input voltage to 9V when batt full.Aseda Aboagye2020-05-051-0/+31
* CHERRY-PICK: nocturne: Enable active discharge on 1.8U and 1.2UAseda Aboagye2020-05-051-0/+3
* Waddledoo: enable gpio interrupt for base accelgyro sensorKo_Ko2020-05-051-0/+2
* damu: fix lid sensor rotation matrixScott Chao2020-05-051-6/+6
* morphius: fix accel rotate matrixZick Wei2020-05-051-3/+14
* Zork: Add PI3HDX1204 power control.Edward Hill2020-05-055-5/+41
* bloonchipper: Enable pulldown on SPI masterCraig Hesling2020-05-051-1/+1
* Puff: Disable USB-C DRP auto-toggle and lower power modeAndrew McRae2020-05-051-2/+0
* waddledoo: Hibernate charger ICs when hibernatingAseda Aboagye2020-05-021-0/+10
* servo_v4: Monitor HPD and signal DUT over PD commWai-Hong Tam2020-05-012-5/+93
* Various boards: Shrink UART Tx buffer to save spaceAbe Levkoy2020-05-015-3/+7
* Puff: Add tcpci_dump command and ppc interrupt checkAndrew McRae2020-05-012-0/+7
* OCPC: Add concept of active charger ICAseda Aboagye2020-05-019-9/+10
* servo_v4: Support DP alt-modeWai-Hong Tam2020-04-303-6/+210
* test: Add on-device unit test for STM32 RTCTom Hughes2020-04-304-0/+4
* Bobba: Add battery AP19A5KDavid Huang2020-04-302-0/+30
* trondo: Initial EC imagestabilize-13070.B-masterDavid Wu2020-04-309-0/+1226
* ampton: change sku id 3,4 for g-sensor BMA253 in the lidJames_Chao2020-04-303-12/+43
* HACK: jinlon: Prevent system can't power onDevin Lu2020-04-301-0/+22
* berknip: Initial EC imageZick Wei2020-04-308-0/+868
* Wheelie: Initial EC imageTommie Lin2020-04-308-0/+1264
* jinlon: Reduce input voltage to 5V when battery fullDevin Lu2020-04-301-1/+28
* Jinlon: Select CONFIG_KEYBOARD_REFRESH_ROW3Rajat Jain2020-04-301-0/+1
* Waddledee: Increase PDCMD task sizeDiana Z2020-04-301-1/+1
* kakadu: implementation of Vconn boostScott Chao2020-04-291-2/+2
* it83xx/adc: enabled GPIO alternate mode by default for pin into gpio.inc mark...tim2020-04-295-4/+11
* Zork: Configure GPIO86 EC_H1_PACKET_MODE lowEdward Hill2020-04-296-24/+6
* stm32: Enable more on-device unit testsTom Hughes2020-04-295-5/+45
* Zork: Move charger I2C to match HW changeEdward Hill2020-04-295-17/+12
* damu: correct battery i2c portScott Chao2020-04-281-1/+1
* malefor: turn off USB4 and Thunderbolt supportxiong.huang2020-04-283-28/+13
* malefor: define led behaviorxiong.huang2020-04-284-100/+96
* volteer: move the PWM configuration and LED support from baseboard to boardsxiong.huang2020-04-2812-2/+507
* kakadu: update led pwm dutyScott Chao2020-04-271-2/+2
* kakadu: fix firmware_ECCharging failedScott Chao2020-04-271-1/+1
* garg: add HDMI SKU IDDevin Lu2020-04-271-1/+1
* damu: enlarge CHARGER task stack to 1024 bytesPaul Ma2020-04-271-1/+1
View Lorry Controller Status