| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the interest of making long-term branch maintenance incur as little
technical debt on us as possible, we should not maintain any files on
the branch we are not actually using.
This has the added effect of making it extremely clear when merging CLs
from the main branch when changes have the possibility to affect us.
The follow-on CL adds a convenience script to actually pull updates from
the main branch and generate a CL for the update.
BUG=b:204206272
BRANCH=ish
TEST=make BOARD=arcada_ish && make BOARD=drallion_ish
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I17e4694c38219b5a0823e0a3e55a28d1348f4b18
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/3262038
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Tom Hughes <tomhughes@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
samus: AUE in M91, M92 pushed to stable already
samus_pd: samus pd chip
dragonegg: canceled
cheza: canceled
flapjack_scp: flapjack was canceled
atlas_ish: atlas shipped, but ish project canceled
sklrvp,glkrvp: these are pretty old intel reference boards and the
portage overlays were already deleted ... assume nobody needs the
EC firmware anymore either
BUG=none
BRANCH=none
TEST=buildall
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I794867ac82f37ffa2267e2e59ac02bc381688c57
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/3069716
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Replace them with charger_get_input_current_limit which is
aligned to the old usage, no funcional changes.
Keep OCPC charger_get_input_current uses as was, since it
is its intended use.
Also, implement
- isl923x_get_input_current, raa48900_get_input_current
- sm5803_get_input_current_limit
BUG=b:171853295
TEST=1. grep "\<charger_get_input_current\>"; only ocpc uses the function.
2. make buildall
3. test with CL:2569086 on waddledee(sm5803), waddledoo(raa489000),
hayato(isl923x), pompom(isl923x), and ensure the output
of `curr 0|1` equalts to the report of power meter.
BRANCH=none
Change-Id: I71aca33cbc88dda9b0238cb71b1609665a9c9a7f
Signed-off-by: Eric Yilun Lin <yllin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2569085
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
charger_set_input_current was actually sets the input current limit,
so renames it to charger_set_input_current_limit.
BUG=b:171853295
TEST=make buildall
TEST=not output from `grep -r "\<charger_set_input_current\>"`
BRANCH=none
Change-Id: Icf4e99f287a7d4fc2d9560e8502e46cc07bfc085
Signed-off-by: Eric Yilun Lin <yllin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2569083
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Casta needs to support 2 chargers(ISL9238 & BQ25710)
BUG=b:168122776
BRANCH=firmware-octopus-11297.B
TEST=None
Signed-off-by: YongBeum.Ha <ybha@samsung.corp-partner.google.com>
Change-Id: I18758acbd0920132c2958bf9d238b4eac3fb5b73
Signed-off-by: YongBeum.Ha <ybha@samsung.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2428354
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With upcoming boards which use multiple charger chips, the EC codebase
needs to be changed to assume chargers may have different I2C ports.
This commit creates the driver structure and wrapper functions, which
for now are hard-coded to chip 0 for equivalent behavior with previous
code. A general charger config is created for all boards in charger.c
for now, which uses the build information to fill in the structure.
All boards will default to defining CONFIG_CHARGER_SINGLE_CHIP, which in
turn defines a CHARGER_SOLO which can be used by drivers which have code
that needs to determine charger numbers. For boards which have multiple
chips, they may undefine this config and should generate build errors if
their driver is still using the hardcoded charger reference of
CHARGER_SOLO. Older drivers may continue using CHARGER_SOLO in
non-static functions until they're needed in a multiple charger board.
For boards which may be supporting different I2C configurations for the
charger over board versions, they may define
CONFIG_CHARGER_RUNTIME_CONFIG to fill in these fields after boot.
BRANCH=none
BUG=b:147672225
TEST=builds, chargers on hatch and octopus work
Change-Id: I390ede494226252e512595c48099fa1288ffe93e
Signed-off-by: Diana Z <dzigterman@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2008451
Reviewed-by: Jett Rink <jettrink@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ran the following command:
git grep -l 'Copyright (c)' | \
xargs sed -i 's/Copyright (c)/Copyright/g'
BRANCH=none
BUG=none
TEST=make buildall -j
Change-Id: I6cc4a0f7e8b30d5b5f97d53c031c299f3e164ca7
Signed-off-by: Tom Hughes <tomhughes@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/1663262
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
BUG=None
TEST=`make buildall -j`
BRANCH=None
Change-Id: I667e471d4d9187f530da7ae8807c8aa339a17847
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/663817
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Set bq24773 charger switching frequency to 600kHz for
efficiency.
BUG=none
BRANCH=none
TEST=removed #ifdef BOARD_LUCID and tested on samus. verified
that the option0 register was set correctly when charger
plugged in:
> i2cxfer r16 0 0xd4 0
0xe04e
Change-Id: I60d563d0040efc7ca7746985156c4e70b423f3a7
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/300622
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
BUG=none
TEST=Verified with a SMBus analyzer that only the expected device
address is detected on the bus.
BRANCH=none
Change-Id: Ib8c8589544b9ec11127619a1120eb21f211fd690
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/267472
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Divya Jyothi <divya.jyothi@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
'ectool chargestate show' shows the wrong input current since
the function charger_get_input_current() uses REG8_TO_CURRENT.
BUG=None
TEST=Use 'ectool chargestate show' or UART command 'charger'
check the input current value.
BRANCH=None
Signed-off-by: james_chao <james_chao@asus.com>
Change-Id: I29229ea1ef22811035b500c7a33fedee6562db35
Reviewed-on: https://chromium-review.googlesource.com/259842
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Divya Jyothi <divya.jyothi@intel.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Divya Jyothi <divya.jyothi@intel.com>
Commit-Queue: Shawn N <shawnn@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for bq24770 (smbus) in the bq24773 (i2c) driver.
BUG=None
TEST=Use the UART command "charger" and check the charger information.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ie5f5af60e93aa73d9ef68115af36a8d28f6d6c2b
Reviewed-on: https://chromium-review.googlesource.com/259870
Reviewed-by: BoChao Jhan <james_chao@asus.com>
Reviewed-by: Divya Jyothi <divya.jyothi@intel.com>
Commit-Queue: Divya Jyothi <divya.jyothi@intel.com>
Tested-by: Divya Jyothi <divya.jyothi@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Occasionally the charge circuit on samus gets wedged and will not
charge. This change detects when the charge circuit has failed
and automatically recovers from it. It uses the BQ PROCHOT warning
to detect the failure by setting PROCHOT to trigger when the BQ
thinks input current is higher than the input current limit. When
the failure is detected, the EC disables charging and tells PD MCU
to disable CHARGE_EN, then a couple seconds later, it re-enables
charging.
This CL also adds more communication between EC and PD for the EC
to be able to set the charge state for the PD. Valid charge states
are: No charging allowed, 5V charging only, and max charging. The
EC uses this as such:
- When the EC gets AC present interrupt, it sets off a deferred
function to change charge state to max charging after some delay
to give time for the charge circuit to settle down.
- When the EC gets AC disconnect interrupt, it disables charging
briefly, enables learn mode, and then sets 5V charging allowed.
This allows for the same starting conditions in the charge circuit
for every AC attach.
- When the EC detects a wedged charge circuit, it disables charging
and waits a few seconds before re-enabling 5V only charging.
Additionally, this change moves the charging cutoff in S3/S5/G3 when
the battery is full to the EC. With the added control for the EC
to set the PD charging state, it is more convenient for the EC to
manage cutting off charging when battery is full.
BUG=chrome-os-partner:36081
BRANCH=samus
TEST=test the basics:
- connect/disconnect zinger a bunch of times
- connect and disconnect two zingers in different order
- connect two zingers and charge override between the two
test the automatic charge wedge recover:
- wedge the charge circuit by setting charger voltage under battery
voltage: "charger voltage 7000"
- wait a few seconds for the system to recover and check it is charging
with "battery" command
test full battery charge cutoff:
- added console command to change battery soc in board/samus/extpower.c:
static int cmd_battfake(int argc, char **argv)
{
char *e;
battery_soc = strtoi(argv[1], &e, 10);
batt_soc_change();
return EC_SUCCESS;
}
DECLARE_CONSOLE_COMMAND(battfake, cmd_battfake, "", "", NULL);
- in S0, tested "battfake 100" does not disable charging.
- in G3, tested "battfake 100" disables charging and "battfake 99"
re-enables charging.
- set "battfake 100" and tested transitioning to S0 enables charging and
transitioning to S5 disables charging.
- attached two chargers and used charge override to select active port.
then toggled "battfake 100" to "battfake 99" back and forth and verified
charge override port is still the same.
test third-party 12V charger:
- plug in a bunch of times and make sure we stay at 5V for 500ms and then
transition to 12V
test with no battery:
- tested five different units with no battery and just zinger. 3/5 boot,
while the other 2 don't. But, the 2 that don't boot without battery also
can't boot w/o battery when this CL is reverted, so I don't think this
change is causing the problem, I think there is an electrical limitation.
test with EVT zinger:
- EVT zingers (P2 - C2) negotiate very quickly after connection, which
can cause INA problems w/o this CL. Tested an EVT zinger with samus and
did a bunch of connections and disconnections and verified that we always
wait at 5V for 500ms and that we don't wedge the INA circuit on connect.
test backwards compatibility:
- test new PD with old EC and make sure we can charge with zinger.
(note that if the charge circuit wedges, we won't be able to unwedge it).
- test old PD with new EC and make sure we can charge with zinger.
Change-Id: I7703b7a2ab1209d7f559b265b03517e79c74b16a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/245253
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Turn off prochot warning on bq24773 by default because our
battery can always supply enough power for the whole system
so we don't need to throttle the CPU if the BQ senses too much
input current.
BUG=chrome-os-partner:34885
BRANCH=samus
TEST=force BQ into it's prochot condition on samus by setting
the charging voltage temporarily below the battery voltage, which
causes INA to turn off and the BQ to think IADP is > 4.1A. in
this condition PROCHOT is normally asserted and CPU slows down,
but with this patch PROCHOT is not asserted and the CPU does not
slow down.
Change-Id: I658dbe568b7bfe94944ef90d6d59656a0683c8a0
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/243231
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When charger is initialized disable the LEARN option i.e. reenable
charging on AC power
BUG=chrome-os-partner:32320
TEST=set DUT to discharge on AC and then reflash EC. Ensure that
charging begins again.
BRANCH=none
Change-Id: I3e83db27ab49548d5491548fa624899865c11bfb
Signed-off-by: Mohammed Habibulla <moch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222644
Reviewed-by: Randall Spangler <rspangler@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently charge state machine resets input current limit to default
every time AC is connected. Problem is by the time charge state machine
gets around to setting input current, it could have already been set
by successful PD negotiation, and this ends up overriding that value.
This fix has the state machine store desired input current limit, as
determined from PD negotation or any other place, and send last desired
input current limit on AC connect.
BUG=chrome-os-partner:24461
BRANCH=none
TEST=load on samus, test toggling between "pd 0 dev 5" and "pd 0 dev 20",
and test plugging and unplugging zinger numerous times, and verify charger
command always gives the expected input current limit based on PD
negotiation.
Change-Id: I18d8acc9e2085739e783c9c70c682d46bcce7fdb
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211639
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ACOK input to the EC is not connected to the charger so
that signal cannot be relied on for AC presence. Instead
have the PD report when it negotiates to 20V and when it
disconnects and have the EC use that for AC presence.
BUG=chrome-os-partner:29841
BRANCH=none
TEST=test charging with zinger on samus system.
Change-Id: Ia9096a24ab05d110e31910218dc8c214a846a9a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/205145
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
| |
BUG=none
BRANCH=none
TEST=buildall -j
Change-Id: I125fbe7716f6c8b78011c3a39745ec4992074795
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/199796
Reviewed-by: Alec Berg <alecaberg@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Typically bq24xxx charging chip limits input current to minimum of
register value and ILIM pin. For fruitpie, the current limit will
be decided solely in software, and the hardware pin will be ignored.
BUG=chrome-os-partner:28611,chrome-os-partner:28311
BRANCH=none
TEST=Tested on fruitpie. Verified that current limit can be set
above the ILIM pin value of 500mA.
Change-Id: Ia687446f95f9d18fde9d2b4ebb0e1c093aebf885
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/198940
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
|
|
Add support TI BQ24773 1S/2S/3S NVDC battery charger.
This is not a "Smart Battery" compliant charger IC, it should and cannot
use the sbc_ helpers.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=on FruitPie, run "charger" command on the EC console,
add the charger task and see the battery charging.
Change-Id: I6f470184f0ce424a05007e493d802dcdb2156477
Reviewed-on: https://chromium-review.googlesource.com/191212
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
|