From 054c9fe6a6b32098f5fa881d49c6f43707d8d042 Mon Sep 17 00:00:00 2001 From: zyw Date: Mon, 21 Jul 2014 19:30:59 -0400 Subject: veyron: Modify board config This patch is base on new hardware board, veyron has not some stuff, such as power led, charge en BUG=None TEST=Read log with servo board, it has reponse when type some commends BRANCH=None Change-Id: I45502fd1278f69db5e46fc9ab1deaee02fc8708f Signed-off-by: zyw Reviewed-on: https://chromium-review.googlesource.com/209231 Reviewed-by: Alexandru Stan Commit-Queue: Alexandru Stan Tested-by: Alexandru Stan --- power/build.mk | 1 + power/rockchip.c | 635 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 636 insertions(+) create mode 100644 power/rockchip.c (limited to 'power') diff --git a/power/build.mk b/power/build.mk index 5819b623c1..e97371d125 100644 --- a/power/build.mk +++ b/power/build.mk @@ -10,5 +10,6 @@ power-$(CONFIG_CHIPSET_BAYTRAIL)+=baytrail.o power-$(CONFIG_CHIPSET_GAIA)+=gaia.o power-$(CONFIG_CHIPSET_HASWELL)+=haswell.o power-$(CONFIG_CHIPSET_IVYBRIDGE)+=ivybridge.o +power-$(CONFIG_CHIPSET_ROCKCHIP)+=rockchip.o power-$(CONFIG_CHIPSET_TEGRA)+=tegra.o power-$(CONFIG_POWER_COMMON)+=common.o diff --git a/power/rockchip.c b/power/rockchip.c new file mode 100644 index 0000000000..38fa3461d9 --- /dev/null +++ b/power/rockchip.c @@ -0,0 +1,635 @@ +/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* + * Rockchip SoC power sequencing module for Chrome EC + * + * This implements the following features: + * + * - Cold reset powers on the AP + * + * When powered off: + * - Press pwron turns on the AP + * - Hold pwron turns on the AP, and then 9s later turns it off and leaves + * it off until pwron is released and pressed again + * + * When powered on: + * - The PMIC PWRON signal is released <= 1 second after the power button is + * released + * - Holding pwron for 10.2s powers off the AP + * - Pressing and releasing pwron within that 10.2s is ignored + * - If POWER_GOOD is dropped by the pmic, then we cut off the pmic source + * - If SUSPEND_L goes low, enter suspend mode. + * + */ + +#include "battery.h" +#include "charge_state.h" +#include "chipset.h" /* This module implements chipset functions too */ +#include "clock.h" +#include "common.h" +#include "console.h" +#include "gpio.h" +#include "hooks.h" +#include "lid_switch.h" +#include "keyboard_scan.h" +#include "power.h" +#include "power_button.h" +#include "power_led.h" +#include "system.h" +#include "task.h" +#include "timer.h" +#include "util.h" + +/* Console output macros */ +#define CPUTS(outstr) cputs(CC_CHIPSET, outstr) +#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args) + +/* masks for power signals */ +#define IN_POWER_GOOD POWER_SIGNAL_MASK(RK_POWER_GOOD) +#define IN_SUSPEND POWER_SIGNAL_MASK(RK_SUSPEND_ASSERTED) + +/* Long power key press to force shutdown */ +#define DELAY_FORCE_SHUTDOWN (10200 * MSEC) /* 10.2 seconds */ + +/* + * The minimum time to assert the PMIC PWRON pin is 20ms. + * Give it longer to ensure the PMIC doesn't lose it. + */ +#define PMIC_PWRON_DEBOUNCE_TIME (200 * MSEC * 3) + +/* + * The minimum time to assert the PMIC THERM pin is 32us. However, + * it needs to be extended to about 50ms to let the 5V rail + * dissipate fully. + */ +#define PMIC_THERM_HOLD_TIME (50 * MSEC) + +/* + * If the power key is pressed to turn on, then held for this long, we + * power off. + * + * Normal case: User releases power button and chipset_task() goes + * into the inner loop, waiting for next event to occur (power button + * press or power good == 0). + */ +#define DELAY_SHUTDOWN_ON_POWER_HOLD (10200 * MSEC) /* 10.2 seconds */ + +/* + * The hold time for pulling down the PMIC_WARM_RESET_L pin so that + * the AP can entery the recovery mode (flash SPI flash from USB). + */ +#define PMIC_WARM_RESET_L_HOLD_TIME (4 * MSEC) + +/* + * The first time the PMIC sees power (AC or battery) it needs 200ms (+/-12% + * oscillator tolerance) for the RTC startup. In addition there is a startup + * time of approx. 0.5msec until V2_5 regulator starts up. */ +#define PMIC_RTC_STARTUP (225 * MSEC) + +/* TODO(crosbug.com/p/25047): move to HOOK_POWER_BUTTON_CHANGE */ +/* 1 if the power button was pressed last time we checked */ +static char power_button_was_pressed; + +/* 1 if lid-open event has been detected */ +static char lid_opened; + +/* time where we will power off, if power button still held down */ +static timestamp_t power_off_deadline; + +/* force AP power on (used for recovery keypress) */ +static int auto_power_on; + +enum power_request_t { + POWER_REQ_NONE, + POWER_REQ_OFF, + POWER_REQ_ON, + + POWER_REQ_COUNT, +}; + +static enum power_request_t power_request; + + +/* Forward declaration */ +static void chipset_turn_off_power_rails(void); + + +/** + * Set the AP RESET signal. + * + * This fucntion is for backward-compatible. + * + * AP_RESET_L (PB3) is stuffed before rev <= 2.0 and connected to PMIC RESET. + * After rev >= 2.2, this is removed. This should not effected the new board. + * + * @param asserted Assert (=1) or deassert (=0) the signal. This is the + * logical level of the pin, not the physical level. + */ +static void set_ap_reset(int asserted) +{ + /* Signal is active-high */ + gpio_set_level(GPIO_AP_RESET_H, asserted ? 1 : 0); +} + + +/** + * Set the PMIC PWRON signal. + * + * Note that asserting requires holding for PMIC_PWRON_DEBOUNCE_TIME. + * + * @param asserted Assert (=1) or deassert (=0) the signal. This is the + * logical level of the pin, not the physical level. + */ +static void set_pmic_pwron(int asserted) +{ + /* Signal is active-low */ + gpio_set_level(GPIO_PMIC_PWRON_L, asserted ? 0 : 1); +} + +/** + * Set the PMIC source to force shutdown the AP. + * + * @param asserted Assert (=1) or deassert (=0) the signal. This is the + * logical level of the pin, not the physical level. + */ +static void set_pmic_source(int asserted) +{ + /* Signal is active-high */ + gpio_set_level(GPIO_PMIC_THERM_H, asserted ? 1 : 0); +} + +/** + * Check for some event triggering the shutdown. + * + * It can be either a long power button press or a shutdown triggered from the + * AP and detected by reading POWER_GOOD. + * + * @return non-zero if a shutdown should happen, 0 if not + */ +static int check_for_power_off_event(void) +{ + timestamp_t now; + int pressed = 0; + + /* + * Check for power button press. + */ + if (power_button_is_pressed()) { + pressed = 1; + } else if (power_request == POWER_REQ_OFF) { + power_request = POWER_REQ_NONE; + return 4; /* return non-zero for shudown down */ + } + +#ifdef HAS_TASK_KEYSCAN + /* Dis/Enable keyboard scanning when the power button state changes */ + if (!pressed || pressed != power_button_was_pressed) + keyboard_scan_enable(!pressed, KB_SCAN_DISABLE_POWER_BUTTON); +#endif + + now = get_time(); + if (pressed) { + set_pmic_pwron(1); + usleep(PMIC_PWRON_DEBOUNCE_TIME); + + if (!power_button_was_pressed) { + power_off_deadline.val = now.val + DELAY_FORCE_SHUTDOWN; + CPRINTS("power waiting for long press %u", + power_off_deadline.le.lo); + } else if (timestamp_expired(power_off_deadline, &now)) { + power_off_deadline.val = 0; + CPRINTS("power off after long press now=%u, %u", + now.le.lo, power_off_deadline.le.lo); + return 2; + } + } else if (power_button_was_pressed) { + CPRINTS("power off cancel"); + set_pmic_pwron(0); + } + + power_button_was_pressed = pressed; + + /* POWER_GOOD released by AP : shutdown immediately */ + if (!power_has_signals(IN_POWER_GOOD)) + return 3; + + return 0; +} + +static void rockchip_lid_event(void) +{ + /* Power task only cares about lid-open events */ + if (!lid_is_open()) + return; + + lid_opened = 1; + task_wake(TASK_ID_CHIPSET); +} +DECLARE_HOOK(HOOK_LID_CHANGE, rockchip_lid_event, HOOK_PRIO_DEFAULT); + +enum power_state power_chipset_init(void) +{ + int init_power_state; + uint32_t reset_flags = system_get_reset_flags(); + + /* + * Force the AP shutdown unless we are doing SYSJUMP. Otherwise, + * the AP could stay in strange state. + */ + if (!(reset_flags & RESET_FLAG_SYSJUMP)) { + CPRINTS("not sysjump; forcing AP shutdown"); + chipset_turn_off_power_rails(); + + /* + * The warm reset triggers AP into the RK recovery mode ( + * flash SPI from USB). + */ + chipset_reset(0); + + init_power_state = POWER_G3; + } else { + /* In the SYSJUMP case, we check if the AP is on */ + if (power_get_signals() & IN_POWER_GOOD) + init_power_state = POWER_S0; + else + init_power_state = POWER_G3; + } + + /* Leave power off only if requested by reset flags */ + if (!(reset_flags & RESET_FLAG_AP_OFF) && + !(reset_flags & RESET_FLAG_SYSJUMP)) { + CPRINTS("auto_power_on set due to reset_flag 0x%x", + system_get_reset_flags()); + auto_power_on = 1; + } + + /* + * Some batteries use clock stretching feature, which requires + * more time to be stable. See http://crosbug.com/p/28289 + */ + battery_wait_for_stable(); + + return init_power_state; +} + +/*****************************************************************************/ +/* Chipset interface */ + +static void chipset_turn_off_power_rails(void) +{ + /* Release the power button, if it was asserted */ + set_pmic_pwron(0); + /* Close the pmic power source immediately */ + set_pmic_source(0); + + /* Hold the reset pin so that the AP stays in off mode (rev <= 2.0) */ + set_ap_reset(1); +} + +void chipset_force_shutdown(void) +{ + chipset_turn_off_power_rails(); + + /* clean-up internal variable */ + power_request = POWER_REQ_NONE; +} + +/*****************************************************************************/ + +/** + * Check if there has been a power-on event + * + * This checks all power-on event signals and returns non-zero if any have been + * triggered (with debounce taken into account). + * + * @return non-zero if there has been a power-on event, 0 if not. + */ +static int check_for_power_on_event(void) +{ + int ap_off_flag; + + ap_off_flag = system_get_reset_flags() & RESET_FLAG_AP_OFF; + system_clear_reset_flags(RESET_FLAG_AP_OFF); + /* check if system is already ON */ + if (power_get_signals() & IN_POWER_GOOD) { + if (ap_off_flag) { + CPRINTS( + "system is on, but " + "RESET_FLAG_AP_OFF is on"); + return 0; + } else { + CPRINTS( + "system is on, thus clear " + "auto_power_on"); + /* no need to arrange another power on */ + auto_power_on = 0; + return 1; + } + } + + /* power on requested at EC startup for recovery */ + if (auto_power_on) { + auto_power_on = 0; + return 2; + } + + /* Check lid open */ + if (lid_opened) { + lid_opened = 0; + return 3; + } + + /* check for power button press */ + if (power_button_is_pressed()) + return 4; + + if (power_request == POWER_REQ_ON) { + power_request = POWER_REQ_NONE; + return 5; + } + + return 0; +} + +/** + * Power on the AP + */ +static void power_on(void) +{ + uint64_t t; + + /* enable interrupt */ + gpio_set_flags(GPIO_SUSPEND_L, GPIO_INPUT | GPIO_INT_BOTH); + /* Make sure we de-assert the PMI_SOURCE and AP_RESET_L pin. */ + set_pmic_source(1); + set_ap_reset(0); + + /* + * Before we push PMIC power button, wait for the PMI RTC ready, which + * takes PMIC_RTC_STARTUP from the AC/battery is plugged in. + */ + t = get_time().val; + if (t < PMIC_RTC_STARTUP) { + uint32_t wait = PMIC_RTC_STARTUP - t; + CPRINTS("wait for %dms for PMIC RTC start-up", + wait / MSEC); + usleep(wait); + } + + /* + * When power_on() is called, we are at S5S3. Initialize components + * to ready state before AP is up. + */ + hook_notify(HOOK_CHIPSET_PRE_INIT); + /* Change SPI1_NSS pin to high-Z to reduce power draw, + * until AP running + */ + gpio_set_flags(GPIO_SPI1_NSS, GPIO_INPUT); + /* Push the power button */ + set_pmic_pwron(1); + usleep(PMIC_PWRON_DEBOUNCE_TIME); + gpio_set_flags(GPIO_SPI1_NSS, GPIO_INPUT | GPIO_INT_BOTH + | GPIO_PULL_UP); + disable_sleep(SLEEP_MASK_AP_RUN); + + powerled_set_state(POWERLED_STATE_ON); + + /* Call hooks now that AP is running */ + hook_notify(HOOK_CHIPSET_STARTUP); + + CPRINTS("AP running ..."); +} + +/** + * Wait for the power button to be released + * + * @param timeout_us Timeout in microseconds, or -1 to wait forever + * @return EC_SUCCESS if ok, or + * EC_ERROR_TIMEOUT if power button failed to release + */ +static int wait_for_power_button_release(unsigned int timeout_us) +{ + timestamp_t deadline; + timestamp_t now = get_time(); + + deadline.val = now.val + timeout_us; + + while (power_button_is_pressed()) { + now = get_time(); + if (timeout_us < 0) { + task_wait_event(-1); + } else if (timestamp_expired(deadline, &now) || + (task_wait_event(deadline.val - now.val) == + TASK_EVENT_TIMER)) { + CPRINTS("power button not released in time"); + return EC_ERROR_TIMEOUT; + } + } + + CPRINTS("power button released"); + power_button_was_pressed = 0; + return EC_SUCCESS; +} + +/** + * Power off the AP + */ +static void power_off(void) +{ + /* Call hooks before we drop power rails */ + hook_notify(HOOK_CHIPSET_SHUTDOWN); + /* switch off all rails */ + chipset_turn_off_power_rails(); + /* Change SUSPEND_L pin to high-Z to reduce power draw. */ + gpio_set_flags(GPIO_SUSPEND_L, GPIO_INPUT); + + lid_opened = 0; + enable_sleep(SLEEP_MASK_AP_RUN); + powerled_set_state(POWERLED_STATE_OFF); + /* Wait POWER GOOD pin to low */ + usleep(PMIC_THERM_HOLD_TIME); + CPRINTS("power shutdown complete"); +} + +void chipset_reset(int is_cold) +{ + if (is_cold) { + CPRINTS("EC triggered cold reboot"); + power_off(); + /* After POWER_GOOD is dropped off, + * the system will be on again + */ + power_request = POWER_REQ_ON; + } else { + CPRINTS("EC triggered warm reboot"); + CPRINTS("assert GPIO_PMIC_WARM_RESET_L for %d ms", + PMIC_WARM_RESET_L_HOLD_TIME / MSEC); + gpio_set_level(GPIO_PMIC_WARM_RESET_L, 0); + usleep(PMIC_WARM_RESET_L_HOLD_TIME); + gpio_set_level(GPIO_PMIC_WARM_RESET_L, 1); + } +} + +enum power_state power_handle_state(enum power_state state) +{ + int value; + static int boot_from_g3; + + switch (state) { + case POWER_G3: + boot_from_g3 = check_for_power_on_event(); + if (boot_from_g3) + return POWER_G3S5; + break; + + case POWER_G3S5: + return POWER_S5; + + case POWER_S5: + if (boot_from_g3) { + value = boot_from_g3; + boot_from_g3 = 0; + } else { + value = check_for_power_on_event(); + } + + if (value) { + CPRINTS("power on %d", value); + return POWER_S5S3; + } + return state; + + case POWER_S5S3: + power_on(); + if (power_wait_signals(IN_POWER_GOOD) == EC_SUCCESS) { + CPRINTS("POWER_GOOD seen"); + if (wait_for_power_button_release( + DELAY_SHUTDOWN_ON_POWER_HOLD) == + EC_SUCCESS) { + set_pmic_pwron(0); + return POWER_S3; + } else { + CPRINTS("long-press button, shutdown"); + power_off(); + /* + * Since the AP may be up already, return S0S3 + * state to go through the suspend hook. + */ + return POWER_S0S3; + } + } else { + CPRINTS("POWER_GOOD not seen in time"); + } + set_pmic_pwron(0); + return POWER_S5; + + case POWER_S3: + if (!(power_get_signals() & IN_POWER_GOOD)) + return POWER_S3S5; + else if (!(power_get_signals() & IN_SUSPEND)) + return POWER_S3S0; + return state; + + case POWER_S3S0: + powerled_set_state(POWERLED_STATE_ON); + hook_notify(HOOK_CHIPSET_RESUME); + return POWER_S0; + + case POWER_S0: + value = check_for_power_off_event(); + if (value) { + CPRINTS("power off %d", value); + power_off(); + return POWER_S0S3; + } else if (power_get_signals() & IN_SUSPEND) + return POWER_S0S3; + return state; + + case POWER_S0S3: + if (lid_is_open()) + powerled_set_state(POWERLED_STATE_SUSPEND); + else + powerled_set_state(POWERLED_STATE_OFF); + /* Call hooks here since we don't know it prior to AP suspend */ + hook_notify(HOOK_CHIPSET_SUSPEND); + return POWER_S3; + + case POWER_S3S5: + wait_for_power_button_release(-1); + return POWER_S5; + + case POWER_S5G3: + return POWER_G3; + } + + return state; +} + +static void powerbtn_rockchip_changed(void) +{ + task_wake(TASK_ID_CHIPSET); +} +DECLARE_HOOK(HOOK_POWER_BUTTON_CHANGE, powerbtn_rockchip_changed, + HOOK_PRIO_DEFAULT); + +/*****************************************************************************/ +/* Console debug command */ + +static const char *power_req_name[POWER_REQ_COUNT] = { + "none", + "off", + "on", +}; + +/* Power states that we can report */ +enum power_state_t { + PSTATE_UNKNOWN, + PSTATE_OFF, + PSTATE_SUSPEND, + PSTATE_ON, + + PSTATE_COUNT, +}; + +static const char * const state_name[] = { + "unknown", + "off", + "suspend", + "on", +}; + +static int command_power(int argc, char **argv) +{ + int v; + + if (argc < 2) { + enum power_state_t state; + + state = PSTATE_UNKNOWN; + if (chipset_in_state(CHIPSET_STATE_ANY_OFF)) + state = PSTATE_OFF; + if (chipset_in_state(CHIPSET_STATE_SUSPEND)) + state = PSTATE_SUSPEND; + if (chipset_in_state(CHIPSET_STATE_ON)) + state = PSTATE_ON; + ccprintf("%s\n", state_name[state]); + + return EC_SUCCESS; + } + + if (!parse_bool(argv[1], &v)) + return EC_ERROR_PARAM1; + + power_request = v ? POWER_REQ_ON : POWER_REQ_OFF; + ccprintf("Requesting power %s\n", power_req_name[power_request]); + task_wake(TASK_ID_CHIPSET); + + return EC_SUCCESS; +} +DECLARE_CONSOLE_COMMAND(power, command_power, + "on/off", + "Turn AP power on/off", + NULL); -- cgit v1.2.1