/* Copyright 2021 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Asurada baseboard-specific configuration */

#include "adc.h"
#include "button.h"
#include "charge_manager.h"
#include "charger.h"
#include "charger.h"
#include "charge_state.h"
#include "charge_state_v2.h"
#include "chipset.h"
#include "common.h"
#include "console.h"
#include "driver/accelgyro_bmi_common.h"
#include "driver/accel_lis2dw12.h"
#include "driver/als_tcs3400.h"
#include "driver/bc12/mt6360.h"
#include "driver/charger/isl923x.h"
#include "driver/ppc/syv682x.h"
#include "driver/tcpm/it83xx_pd.h"
#include "driver/temp_sensor/thermistor.h"
#include "extpower.h"
#include "gpio.h"
#include "hooks.h"
#include "i2c.h"
#include "it5205_sbu.h"
#include "keyboard_scan.h"
#include "lid_switch.h"
#include "motion_sense.h"
#include "power_button.h"
#include "power.h"
#include "regulator.h"
#include "spi.h"
#include "switch.h"
#include "tablet_mode.h"
#include "task.h"
#include "temp_sensor.h"
#include "timer.h"
#include "uart.h"

#include "gpio_list.h"

/* Wake-up pins for hibernate */
enum gpio_signal hibernate_wake_pins[] = {
	GPIO_AC_PRESENT,
	GPIO_LID_OPEN,
	GPIO_POWER_BUTTON_L,
};
int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins);

/*
 * I2C channels (A, B, and C) are using the same timing registers (00h~07h)
 * at default.
 * In order to set frequency independently for each channels,
 * We use timing registers 09h~0Bh, and the supported frequency will be:
 * 50KHz, 100KHz, 400KHz, or 1MHz.
 * I2C channels (D, E and F) can be set different frequency on different ports.
 * The I2C(D/E/F) frequency depend on the frequency of SMBus Module and
 * the individual prescale register.
 * The frequency of SMBus module is 24MHz on default.
 * The allowed range of I2C(D/E/F) frequency is as following setting.
 * SMBus Module Freq = PLL_CLOCK / ((IT83XX_ECPM_SCDCR2 & 0x0F) + 1)
 * (SMBus Module Freq / 510) <=  I2C Freq <= (SMBus Module Freq / 8)
 * Channel D has multi-function and can be used as UART interface.
 * Channel F is reserved for EC debug.
 */

/* I2C ports */
const struct i2c_port_t i2c_ports[] = {
	{"bat_chg",  IT83XX_I2C_CH_A, 100, GPIO_I2C_A_SCL, GPIO_I2C_A_SDA},
	{"sensor",   IT83XX_I2C_CH_B, 400, GPIO_I2C_B_SCL, GPIO_I2C_B_SDA},
	{"usb0",     IT83XX_I2C_CH_C, 400, GPIO_I2C_C_SCL, GPIO_I2C_C_SDA},
	{"usb1",     IT83XX_I2C_CH_E, 400, GPIO_I2C_E_SCL, GPIO_I2C_E_SDA},
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);

int board_allow_i2c_passthru(int port)
{
	return (port == I2C_PORT_VIRTUAL_BATTERY);
}

const struct cc_para_t *board_get_cc_tuning_parameter(enum usbpd_port port)
{
	const static struct cc_para_t
		cc_parameter[CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT] = {
		{
			.rising_time = IT83XX_TX_PRE_DRIVING_TIME_1_UNIT,
			.falling_time = IT83XX_TX_PRE_DRIVING_TIME_2_UNIT,
		},
		{
			.rising_time = IT83XX_TX_PRE_DRIVING_TIME_1_UNIT,
			.falling_time = IT83XX_TX_PRE_DRIVING_TIME_2_UNIT,
		},
	};

	return &cc_parameter[port];
}