/* Copyright 2018 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ /* Octopus board configuration */ #ifndef __CROS_EC_BASEBOARD_H #define __CROS_EC_BASEBOARD_H /******************************************************************************* * EC Config */ /* * By default, enable all console messages excepted HC, ACPI and event: * The sensor stack is generating a lot of activity. */ #define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) #define CONFIG_SUPPRESSED_HOST_COMMANDS \ EC_CMD_CONSOLE_SNAPSHOT, EC_CMD_CONSOLE_READ, EC_CMD_USB_PD_DISCOVERY,\ EC_CMD_USB_PD_POWER_INFO, EC_CMD_PD_GET_LOG_ENTRY, \ EC_CMD_MOTION_SENSE_CMD, EC_CMD_GET_NEXT_EVENT /* * Variant EC defines. Pick one: * VARIANT_OCTOPUS_EC_NPCX796FB * VARIANT_OCTOPUS_EC_ITE8320 */ #if defined(VARIANT_OCTOPUS_EC_NPCX796FB) /* NPCX7 config */ #define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ #define NPCX_TACH_SEL2 0 /* [0:GPIO40/73, 1:GPIO93/A6] as TACH */ #define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ /* Internal SPI flash on NPCX7 */ /* Flash is 1MB but reserve half for future use. */ #define CONFIG_FLASH_SIZE (512 * 1024) #define CONFIG_SPI_FLASH_REGS #define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ /* I2C Bus Configuration */ #define I2C_PORT_BATTERY NPCX_I2C_PORT0_0 #define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 #define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 #define I2C_PORT_EEPROM NPCX_I2C_PORT3_0 #define I2C_PORT_CHARGER NPCX_I2C_PORT4_1 #define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 #define I2C_ADDR_EEPROM_FLAGS 0x50 /* Enable PSL hibernate mode. */ #define CONFIG_HIBERNATE_PSL /* EC variant determines USB-C variant */ #define VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS /* Allow the EC to enter deep sleep in S0 */ #define CONFIG_LOW_POWER_S0 #elif defined(VARIANT_OCTOPUS_EC_ITE8320) /* I2C Bus Configuration */ #define I2C_PORT_BATTERY IT83XX_I2C_CH_A /* Shared bus */ #define I2C_PORT_CHARGER IT83XX_I2C_CH_A /* Shared bus */ #define I2C_PORT_SENSOR IT83XX_I2C_CH_B #define I2C_PORT_USBC0 IT83XX_I2C_CH_C #define I2C_PORT_USBC1 IT83XX_I2C_CH_E #define I2C_PORT_USB_MUX I2C_PORT_USBC0 /* For MUX driver */ #define I2C_PORT_EEPROM IT83XX_I2C_CH_F #define I2C_ADDR_EEPROM_FLAGS 0x50 #define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 2 /* EC variant determines USB-C variant */ #define VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS #else #error Must define a VARIANT_OCTOPUS_EC #endif /* VARIANT_OCTOPUS_EC */ /* Common EC defines */ #define CONFIG_I2C #define CONFIG_I2C_MASTER #define CONFIG_I2C_BUS_MAY_BE_UNPOWERED #define CONFIG_VBOOT_HASH #define CONFIG_VSTORE #define CONFIG_VSTORE_SLOT_COUNT 1 #define CONFIG_CRC8 #define CONFIG_CROS_BOARD_INFO #define CONFIG_BOARD_VERSION_CBI #define CONFIG_LOW_POWER_IDLE #define CONFIG_DPTF #define CONFIG_BOARD_HAS_RTC_RESET #define CONFIG_LED_ONOFF_STATES #define CONFIG_CMD_CHARGEN /* Port80 -- allow larger buffer for port80 messages */ #undef CONFIG_PORT80_HISTORY_LEN #define CONFIG_PORT80_HISTORY_LEN 256 /* * We don't need CONFIG_BACKLIGHT_LID since hardware AND's LID_OPEN and AP * signals with EC backlight enable signal. */ /******************************************************************************* * Battery/Charger/Power Config */ /* * Variant charger defines. Pick one: * VARIANT_OCTOPUS_CHARGER_ISL9238 * VARIANT_OCTOPUS_CHARGER_BQ25703 */ #if defined(VARIANT_OCTOPUS_CHARGER_ISL9238) #define CONFIG_CHARGER_ISL9238 #define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 /* * ISL923x driver sets "Adapter insertion to Switching Debounce" * CONTROL2 REG 0x3DH to 1 which is 150 ms */ #undef CONFIG_EXTPOWER_DEBOUNCE_MS #define CONFIG_EXTPOWER_DEBOUNCE_MS 200 #elif defined(VARIANT_OCTOPUS_CHARGER_BQ25703) #define CONFIG_CHARGER_BQ25703 #define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 /* * From BQ25703: CHRG_OK is HIGH after 50ms deglitch time. */ #undef CONFIG_EXTPOWER_DEBOUNCE_MS #define CONFIG_EXTPOWER_DEBOUNCE_MS 50 #else #error Must define a VARIANT_OCTOPUS_CHARGER #endif /* VARIANT_OCTOPUS_CHARGER */ /* Common charger defines */ #define CONFIG_CHARGE_MANAGER #define CONFIG_CHARGE_RAMP_HW #define CONFIG_CHARGER #define CONFIG_CHARGER_INPUT_CURRENT 512 /* Allow low-current USB charging */ #define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 #define CONFIG_CHARGER_SENSE_RESISTOR 10 #define CONFIG_CHARGER_DISCHARGE_ON_AC #define CONFIG_USB_CHARGER /* Common battery defines */ #define CONFIG_BATTERY_CUT_OFF #define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" #define CONFIG_BATTERY_FUEL_GAUGE #define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_L #define CONFIG_BATTERY_REVIVE_DISCONNECT #define CONFIG_BATTERY_SMART /******************************************************************************* * USB-C Configs * Automatically defined by VARIANT_OCTOPUS_EC_ variant. */ /* * Variant USBC defines. Pick one: * VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS * VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS (requires) */ #if defined(VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS) #define CONFIG_USB_PD_TCPC_LOW_POWER #define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE #if !defined(VARIANT_OCTOPUS_TCPC_0_PS8751) #define CONFIG_USB_PD_TCPM_ANX7447 /* C0 TCPC: ANX7447QN */ #endif #define CONFIG_USB_PD_TCPM_PS8751 /* C1 TCPC: PS8751 */ #define CONFIG_USB_PD_VBUS_DETECT_TCPC #define CONFIG_USBC_PPC_NX20P3483 #elif defined(VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS) #undef CONFIG_USB_PD_TCPC_LOW_POWER #undef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE #define CONFIG_USB_PD_VBUS_DETECT_PPC #define CONFIG_USB_PD_TCPM_ITE_ON_CHIP /* C0 & C1 TCPC: ITE EC */ #define CONFIG_USB_MUX_IT5205 /* C0 MUX: IT5205 */ #define CONFIG_USB_PD_TCPM_PS8751 /* C1 Mux: PS8751 */ #define CONFIG_USBC_PPC_SN5S330 /* C0 & C1 PPC: each SN5S330 */ #define CONFIG_USBC_PPC_VCONN #define CONFIG_USBC_PPC_DEDICATED_INT #else #error Must define a VARIANT_OCTOPUS_USBC #endif /* VARIANT_OCTOPUS_USBC */ /* Common USB-C defines */ #define USB_PD_PORT_TCPC_0 0 #define USB_PD_PORT_TCPC_1 1 #define CONFIG_USB_PID 0x5046 #define CONFIG_USB_DRP_ACC_TRYSRC #define CONFIG_USB_PD_DECODE_SOP #define CONFIG_USB_POWER_DELIVERY #define CONFIG_USB_PD_TCPMV2 #define CONFIG_USB_PD_PORT_MAX_COUNT 2 #define CONFIG_USB_PD_DUAL_ROLE #define CONFIG_USB_PD_LOGGING #define CONFIG_USB_PD_ALT_MODE #define CONFIG_USB_PD_ALT_MODE_DFP #define CONFIG_USB_PD_COMM_LOCKED #define CONFIG_USB_PD_DISCHARGE_PPC #define CONFIG_USB_PD_TRY_SRC #define CONFIG_USBC_SS_MUX #define CONFIG_USBC_VCONN #define CONFIG_USBC_VCONN_SWAP #define CONFIG_USB_PD_VBUS_MEASURE_ADC_EACH_PORT #define CONFIG_USB_PD_TCPM_MUX #define CONFIG_USB_PD_TCPM_TCPCI #define CONFIG_BC12_DETECT_MAX14637 #define CONFIG_HOSTCMD_PD_CONTROL #define CONFIG_CMD_PPC_DUMP /* TODO(b/76218141): Use correct PD delay values */ #define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ #define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ #define PD_VCONN_SWAP_DELAY 5000 /* us */ /* TODO(b/76218141): Use correct PD power values */ #define PD_OPERATING_POWER_MW 15000 #define PD_MAX_POWER_MW 45000 #define PD_MAX_CURRENT_MA 3000 #define PD_MAX_VOLTAGE_MV 20000 /******************************************************************************* * USB-A Configs */ /* Common USB-A defines */ #define USB_PORT_COUNT 2 #define CONFIG_USB_PORT_POWER_SMART #define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY #define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP #define CONFIG_USB_PORT_POWER_SMART_INVERTED #define GPIO_USB1_ILIM_SEL GPIO_USB_A0_CHARGE_EN_L #define GPIO_USB2_ILIM_SEL GPIO_USB_A1_CHARGE_EN_L /******************************************************************************* * SoC / PCH Config */ /* Common SoC / PCH defines */ #define CONFIG_CHIPSET_GEMINILAKE #define CONFIG_CHIPSET_RESET_HOOK #define CONFIG_HOSTCMD_ESPI /* TODO(b/74123961): Enable Virtual Wires after bringup */ #define CONFIG_POWER_COMMON #define CONFIG_POWER_S0IX #define CONFIG_POWER_TRACK_HOST_SLEEP_STATE #define CONFIG_POWER_BUTTON #define CONFIG_POWER_BUTTON_X86 #define CONFIG_POWER_PP5000_CONTROL #define CONFIG_EXTPOWER_GPIO /******************************************************************************* * Keyboard Config */ /* Common Keyboard Defines */ #define CONFIG_CMD_KEYBOARD #define CONFIG_KEYBOARD_BOARD_CONFIG #define CONFIG_KEYBOARD_PROTOCOL_8042 #define CONFIG_KEYBOARD_COL2_INVERTED #define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 #undef CONFIG_KEYBOARD_VIVALDI /******************************************************************************* * Sensor Config */ /* Common Sensor Defines */ #define CONFIG_TABLET_MODE #define CONFIG_GMR_TABLET_MODE #define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L /* * Slew rate on the PP1800_SENSOR load switch requires a short delay on startup. */ #undef CONFIG_MOTION_SENSE_RESUME_DELAY_US #define CONFIG_MOTION_SENSE_RESUME_DELAY_US (10 * MSEC) #ifndef VARIANT_OCTOPUS_NO_SENSORS /* * Interrupt and fifo are only used for base accelerometer * and the lid sensor is polled real-time (in forced mode). */ #define CONFIG_ACCEL_INTERRUPTS /* Enable sensor fifo, must also define the _SIZE and _THRES */ #define CONFIG_ACCEL_FIFO /* Power of 2 - Too large of a fifo causes too much timestamp jitter */ #define CONFIG_ACCEL_FIFO_SIZE 256 /* Depends on how fast the AP boots and typical ODRs */ #define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) #endif /* VARIANT_OCTOPUS_NO_SENSORS */ /* * Sensor stack in EC/Kernel depends on a hardware interrupt pin from EC->AP, so * do not define CONFIG_MKBP_USE_HOST_EVENT since all octopus boards use * hardware pin to send interrupt from EC -> AP (except casta). */ #define CONFIG_MKBP_EVENT #define CONFIG_MKBP_USE_GPIO #ifndef __ASSEMBLER__ #include "gpio_signal.h" /* Forward declare common (within octopus) board-specific functions */ void board_reset_pd_mcu(void); #ifdef VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS void tcpc_alert_event(enum gpio_signal signal); #endif #endif /* !__ASSEMBLER__ */ #endif /* __CROS_EC_BASEBOARD_H */