/* Copyright 2016 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Eve board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

/*
 * By default, enable all console messages excepted HC, ACPI and event:
 * The sensor stack is generating a lot of activity.
 */
#define CC_DEFAULT     (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC)))
#undef CONFIG_HOSTCMD_DEBUG_MODE
#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF

/* EC */
#define CONFIG_ADC
#define CONFIG_BACKLIGHT_LID
#define CONFIG_BOARD_FORCE_RESET_PIN
#define CONFIG_DEVICE_EVENT
#define CONFIG_DPTF
#define CONFIG_DPTF_MULTI_PROFILE
#define CONFIG_FLASH_SIZE_BYTES 0x80000
#define CONFIG_FPU
/* 7 day delay before hibernate */
#undef  CONFIG_HIBERNATE_DELAY_SEC
#define CONFIG_HIBERNATE_DELAY_SEC (3600 * 24 * 7)
/* 1 day delay before hibernate if battery is less than 10% */
#define CONFIG_HIBERNATE_BATT_PCT 10
#define CONFIG_HIBERNATE_BATT_SEC (3600 * 24)
#define CONFIG_I2C
#define CONFIG_I2C_CONTROLLER
#define CONFIG_LED_COMMON
#define CONFIG_LID_SWITCH
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_LTO
#define CONFIG_CHIP_PANIC_BACKUP
#define CONFIG_SOFTWARE_PANIC
#define CONFIG_PWM
#define CONFIG_PWM_KBLIGHT
#define CONFIG_SHA256_UNROLLED
#define CONFIG_SPI_FLASH_REGS
#define CONFIG_SPI_FLASH_W25X40
#define CONFIG_VBOOT_HASH
#define CONFIG_VOLUME_BUTTONS
#define CONFIG_VSTORE
#define CONFIG_VSTORE_SLOT_COUNT 1
#define CONFIG_WATCHDOG_HELP
#define CONFIG_WIRELESS
#define CONFIG_WIRELESS_SUSPEND \
	(EC_WIRELESS_SWITCH_WLAN | EC_WIRELESS_SWITCH_WLAN_POWER)
#define WIRELESS_GPIO_WLAN GPIO_WLAN_OFF_L
#define WIRELESS_GPIO_WLAN_POWER GPIO_PP3300_DX_WLAN
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 256

/* EC console commands */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
#define CONFIG_CMD_BATT_MFG_ACCESS
#define CONFIG_CMD_CHARGER_ADC_AMON_BMON
#define CONFIG_HOSTCMD_PD_CONTROL

/* EC console history configuration */
#undef  CONFIG_CONSOLE_HISTORY
#define CONFIG_CONSOLE_HISTORY 1

/* SOC */
#define CONFIG_CHIPSET_SKYLAKE
#define CONFIG_CHIPSET_HAS_PLATFORM_PMIC_RESET
#define CONFIG_CHIPSET_RESET_HOOK
#define CONFIG_HOSTCMD_ESPI
#define CONFIG_HOSTCMD_ESPI_VW_SLP_S3
#define CONFIG_HOSTCMD_ESPI_VW_SLP_S4

#define CONFIG_KEYBOARD_COL2_INVERTED
#undef  CONFIG_KEYBOARD_VIVALDI
#define CONFIG_KEYBOARD_PROTOCOL_8042
#define CONFIG_KEYBOARD_REFRESH_ROW3
#define CONFIG_TABLET_MODE

/* Battery */
#define CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF
#define CONFIG_BATTERY_CUT_OFF
#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION"
#define CONFIG_BATTERY_LEVEL_NEAR_FULL 94
#define CONFIG_BATTERY_PRESENT_CUSTOM
#define CONFIG_BATTERY_HW_PRESENT_CUSTOM
#define CONFIG_BATTERY_SMART
#define CONFIG_BATTERY_VENDOR_PARAM

/* Charger */
#define CONFIG_CHARGE_MANAGER
#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT
#define CONFIG_CHARGE_RAMP_SW
#define CONFIG_CHARGER
#define CONFIG_CHARGER_BD9995X
#define CONFIG_CHARGER_BD9995X_CHGEN
#define CONFIG_CHARGER_DISCHARGE_ON_AC
#define CONFIG_CHARGER_INPUT_CURRENT 512
#define CONFIG_CHARGER_MAINTAIN_VBAT
#define CONFIG_CHARGER_PROFILE_OVERRIDE
#define CONFIG_CHARGER_PSYS_READ
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
#define BD9995X_IOUT_GAIN_SELECT \
		BD9995X_CMD_PMON_IOUT_CTRL_SET_IOUT_GAIN_SET_20V
#define BD9995X_PSYS_GAIN_SELECT \
		BD9995X_CMD_PMON_IOUT_CTRL_SET_PMON_GAIN_SET_02UAW
#define CONFIG_EXTPOWER_GPIO
#undef   CONFIG_EXTPOWER_DEBOUNCE_MS
#define  CONFIG_EXTPOWER_DEBOUNCE_MS 1000
#define CONFIG_POWER_BUTTON
#define CONFIG_POWER_BUTTON_X86
#define CONFIG_POWER_COMMON
#define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30
#define CONFIG_PWR_STATE_DISCHARGE_FULL

/* Sensor */
#define CONFIG_MKBP_EVENT
/* Don't wake up from suspend on any MKBP event. */
#define CONFIG_MKBP_EVENT_WAKEUP_MASK 0
#define CONFIG_MKBP_USE_HOST_EVENT
#define CONFIG_ACCEL_KXCJ9
#define CONFIG_ALS_SI114X 0x40
#define CONFIG_ALS_SI114X_INT_EVENT \
	TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_LIGHT)
#define CONFIG_ALS_SI114X_POLLING
#define CONFIG_TEMP_SENSOR
#define CONFIG_TEMP_SENSOR_BD99992GW
#define CONFIG_THERMISTOR_NCP15WB
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_MAG_BMI_BMM150
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define CONFIG_ACCELGYRO_SEC_ADDR_FLAGS BMM150_ADDR0_FLAGS
#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT  /* Unused */
#define CONFIG_MAG_CALIBRATE
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_INVALID_CHECK
#define CONFIG_LID_ANGLE_TABLET_MODE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL

/* Enable sensor fifo, must also define the _SIZE and _THRES */
#define CONFIG_ACCEL_FIFO
/* FIFO size is in power of 2. */
#define CONFIG_ACCEL_FIFO_SIZE 256
/* Depends on how fast the AP boots and typical ODRs */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)

/* Enable double tap detection */
#define CONFIG_GESTURE_DETECTION
#define CONFIG_GESTURE_HOST_DETECTION
#define CONFIG_GESTURE_SENSOR_DOUBLE_TAP
#define CONFIG_GESTURE_SAMPLING_INTERVAL_MS 5
#define CONFIG_GESTURE_TAP_THRES_MG 100
#define CONFIG_GESTURE_TAP_MAX_INTERSTICE_T 500
#define CONFIG_GESTURE_DETECTION_MASK BIT(CONFIG_GESTURE_TAP_SENSOR)
#define CONFIG_GESTURE_TAP_SENSOR 1

/* USB */
#define CONFIG_USB_PID 0x504B

#define CONFIG_USB_CHARGER
#define CONFIG_USB_DRP_ACC_TRYSRC
#define CONFIG_USB_PD_ALT_MODE
#define CONFIG_USB_PD_ALT_MODE_DFP
#define CONFIG_USB_PD_COMM_LOCKED
#define CONFIG_USB_PD_DECODE_SOP
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_BD9995X_DELAY_INPUT_PORT_SELECT
#define CONFIG_USB_PD_LOGGING
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_VBUS_DETECT_CHARGER
#define CONFIG_USB_PD_TCPC_BOARD_INIT
#define CONFIG_USB_PD_TCPC_LOW_POWER
#define CONFIG_USB_PD_TCPM_MUX
#define CONFIG_USB_PD_TCPM_ANX3429
#define CONFIG_USB_PD_TCPM_TCPCI
#define CONFIG_USB_PD_TRY_SRC
#undef CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC
#define CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC 2
#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_USB_PD_TCPMV2
#define CONFIG_USBC_SS_MUX
#define CONFIG_USBC_VCONN
#define CONFIG_USBC_VCONN_SWAP

/* Optional feature to configure npcx chip */
#define NPCX_UART_MODULE2	1 /* 1:GPIO64/65 as UART */
#define NPCX_JTAG_MODULE2	0 /* 0:GPIO21/17/16/20 as JTAG */
#define NPCX_TACH_SEL2		0 /* 0:GPIO40/73 as TACH */

/* I2C ports */
#define I2C_PORT_TCPC0		NPCX_I2C_PORT0_0
#define I2C_PORT_TCPC1		NPCX_I2C_PORT0_1
#define I2C_PORT_GYRO		NPCX_I2C_PORT1
#define I2C_PORT_ACCEL		I2C_PORT_GYRO
#define I2C_PORT_LID_ACCEL	NPCX_I2C_PORT2
#define I2C_PORT_ALS		NPCX_I2C_PORT2
#define I2C_PORT_PMIC		NPCX_I2C_PORT3
#define I2C_PORT_BATTERY	NPCX_I2C_PORT3
#define I2C_PORT_CHARGER	NPCX_I2C_PORT3
#define I2C_PORT_THERMAL	I2C_PORT_PMIC
#define I2C_PORT_MP2949		NPCX_I2C_PORT3

/* I2C addresses */
#define I2C_ADDR_BD99992_FLAGS	0x30
#define I2C_ADDR_MP2949_FLAGS	0x20

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum board_version_list {
	BOARD_VERSION_P0,
	BOARD_VERSION_P0B,
	BOARD_VERSION_P1,
	BOARD_VERSION_P1B,
	BOARD_VERSION_EVT,
	BOARD_VERSION_EVTB,
	BOARD_VERSION_DVT,
	BOARD_VERSION_DVTB,
	BOARD_VERSION_PVT,
};

enum temp_sensor_id {
	TEMP_SENSOR_BATTERY,	/* BD99956GW TSENSE */
	TEMP_SENSOR_AMBIENT,	/* BD99992GW SYSTHERM0 */
	TEMP_SENSOR_CHARGER,	/* BD99992GW SYSTHERM1 */
	TEMP_SENSOR_DRAM,	/* BD99992GW SYSTHERM2 */
	TEMP_SENSOR_EMMC,	/* BD99992GW SYSTHERM3 */
	TEMP_SENSOR_GYRO,
	TEMP_SENSOR_COUNT
};

/*
 * The PWM channel enums for the LEDs need to be in Red, Green, Blue order as
 * the 'set_color()' function assumes this order. The left vs right order
 * doesn't matter as long as each side follows RGB order.
 */
enum pwm_channel {
	PWM_CH_KBLIGHT,
	PWM_CH_LED_L_RED,
	PWM_CH_LED_L_GREEN,
	PWM_CH_LED_L_BLUE,
	PWM_CH_LED_R_RED,
	PWM_CH_LED_R_GREEN,
	PWM_CH_LED_R_BLUE,
	PWM_CH_COUNT
};

/*
 * For backward compatibility, to report ALS via ACPI,
 * Define the number of ALS sensors: motion_sensor copy the data to the ALS
 * memmap region.
 */
#define CONFIG_ALS
#define ALS_COUNT 1

/*
 * Motion sensors:
 * When reading through IO memory is set up for sensors (LPC is used),
 * the first 2 entries must be accelerometers, then gyroscope.
 * For BMI160, accel, gyro and compass sensors must be next to each other.
 */
enum sensor_id {
	LID_ACCEL = 0,
	BASE_ACCEL,
	BASE_GYRO,
	BASE_MAG,
	LID_LIGHT,
	SENSOR_COUNT,
};

enum adc_channel {
	ADC_CH_COUNT
};

/*
 * delay to turn on the power supply max is ~16ms.
 * delay to turn off the power supply max is about ~180ms.
 */
#define PD_POWER_SUPPLY_TURN_ON_DELAY	30000  /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY	250000 /* us */

/* delay to turn on/off vconn */

/* Define typical operating power and max power */
#define PD_OPERATING_POWER_MW		15000
#define PD_MAX_POWER_MW			45000
#define PD_MAX_CURRENT_MA		3000
#define PD_MAX_VOLTAGE_MV		20000

/* Board specific handlers */
int board_get_version(void);
void board_reset_pd_mcu(void);
void board_set_tcpc_power_mode(int port, int mode);
void board_tcpc_init(void);
void led_register_double_tap(void);

/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL) | BIT(LID_LIGHT))

#endif /* !__ASSEMBLER__ */

#endif /* __CROS_EC_BOARD_H */