/* Copyright 2017 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Grunt board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

/* Optional features */
#define CONFIG_HIBERNATE_PSL
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */

/* NPCX7 config */
#define NPCX_UART_MODULE2 1  /* GPIO64/65 are used as UART pins. */
#define NPCX_TACH_SEL2    0  /* No tach. */
#define NPCX7_PWM1_SEL    0  /* GPIO C2 is not used as PWM1. */

/* Internal SPI flash on NPCX7 */
/* Flash is 1MB but reserve half for future use. */
#define CONFIG_FLASH_SIZE (512 * 1024)
#define CONFIG_SPI_FLASH_REGS
#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */

#define CONFIG_ADC
#define CONFIG_BACKLIGHT_LID
#define CONFIG_BACKLIGHT_LID_ACTIVE_LOW
#define CONFIG_BOARD_VERSION
#define CONFIG_I2C
#define CONFIG_I2C_MASTER
#define CONFIG_LPC
#define CONFIG_PWM
#define CONFIG_PWM_KBLIGHT
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR_NCP15WB
#define CONFIG_VBOOT_HASH
#define CONFIG_VOLUME_BUTTONS

#define CONFIG_BATTERY_CUT_OFF
#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL
#define CONFIG_BATTERY_SMART

#define CONFIG_BC12_DETECT_BQ24392
#define CONFIG_CHARGER
#define CONFIG_CHARGER_V2
#define CONFIG_CHARGE_MANAGER
#define CONFIG_CHARGER_INPUT_CURRENT 128
#define CONFIG_CHARGER_ISL9238
#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20
#define CONFIG_CHARGE_RAMP_HW
#define CONFIG_USB_CHARGER

#define CONFIG_CHIPSET_STONEY
#define CONFIG_CHIPSET_RESET_HOOK
#define CONFIG_EXTPOWER_GPIO
#define CONFIG_POWER_COMMON
#define CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5
#define CONFIG_POWER_BUTTON
#define CONFIG_POWER_BUTTON_X86
#define CONFIG_UART_HOST 0

#define CONFIG_KEYBOARD_BOARD_CONFIG
#define CONFIG_KEYBOARD_COL2_INVERTED
#define CONFIG_KEYBOARD_PROTOCOL_8042

#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_CMD_PD_CONTROL
#define CONFIG_USB_PD_ALT_MODE
#define CONFIG_USB_PD_ALT_MODE_DFP
#define CONFIG_USB_PD_COMM_LOCKED
#define CONFIG_USB_PD_DISCHARGE
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_LOGGING
#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0
#define CONFIG_USB_PD_PORT_COUNT 2
#define CONFIG_USB_PD_TCPC_BOARD_INIT
#define CONFIG_USB_PD_TCPC_LOW_POWER
#define CONFIG_USB_PD_TCPM_ANX74XX
#define CONFIG_USB_PD_TCPM_MUX
#define CONFIG_USB_PD_TCPM_PS8751
#define CONFIG_USB_PD_TCPM_TCPCI
#define CONFIG_USB_PD_TRY_SRC
#define CONFIG_USB_PD_VBUS_DETECT_PPC
#define CONFIG_USBC_PPC_SN5S330
#define CONFIG_USBC_SS_MUX
#define CONFIG_USBC_SS_MUX_DFP_ONLY
#define CONFIG_USBC_VCONN
#define CONFIG_USBC_VCONN_SWAP

/* USB Type-A Port BC1.2 support */
#define CONFIG_USB_PORT_POWER_SMART
#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
#define CONFIG_USB_PORT_POWER_SMART_INVERTED
#define GPIO_USB1_ILIM_SEL GPIO_USB_A0_CHARGE_EN_L
#define GPIO_USB2_ILIM_SEL GPIO_USB_A1_CHARGE_EN_L

/* TODO(b/69683108): Use correct PD delay values */
#define PD_POWER_SUPPLY_TURN_ON_DELAY	30000  /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY	250000 /* us */
#define PD_VCONN_SWAP_DELAY		5000 /* us */

/* TODO(b/69683178): Use correct PD power values */
#define PD_OPERATING_POWER_MW	15000
#define PD_MAX_POWER_MW		45000
#define PD_MAX_CURRENT_MA	3000
#define PD_MAX_VOLTAGE_MV	20000

#define I2C_PORT_BATTERY	I2C_PORT_POWER
#define I2C_PORT_CHARGER	I2C_PORT_POWER
#define I2C_PORT_POWER		NPCX_I2C_PORT0_0
#define I2C_PORT_TCPC0		NPCX_I2C_PORT1_0
#define I2C_PORT_TCPC1		NPCX_I2C_PORT2_0
#define I2C_PORT_THERMAL	NPCX_I2C_PORT3_0
#define I2C_PORT_KBLIGHT	NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR		NPCX_I2C_PORT7_0
/* Accelerometer and Gyroscope are the same device. */
#define I2C_PORT_ACCEL		I2C_PORT_SENSOR

#define CONFIG_BRINGUP /* TODO(teravest): Remove this later. */

/* Sensors */
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT TASK_EVENT_CUSTOM(4)
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCEL_KX022
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL

/* Thermal */
#define CONFIG_TEMP_SENSOR_SB_TSI

/* FIFO size is a power of 2. */
#define CONFIG_ACCEL_FIFO 1024  /* TODO(teravest): Check this value. */

/* Depends on how fast the AP boots and typical ODRs. */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO / 3)

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum adc_channel {
	ADC_VBUS = -1,
	ADC_TEMP_SENSOR_CHARGER,
	ADC_TEMP_SENSOR_SOC,
	ADC_CH_COUNT
};

enum power_signal {
	X86_SLP_S3_N,
	X86_SLP_S5_N,
	X86_VGATE,
	X86_SPOK,
	POWER_SIGNAL_COUNT
};

enum temp_sensor_id {
	TEMP_SENSOR_CHARGER = 0,
	TEMP_SENSOR_SOC,
	TEMP_SENSOR_CPU,
	TEMP_SENSOR_COUNT
};

enum pwm_channel {
	PWM_CH_KBLIGHT,
	PWM_CH_COUNT
};

enum sensor_id {
	LID_ACCEL,
	BASE_ACCEL,
	BASE_GYRO,
};

/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL)

void board_reset_pd_mcu(void);
void board_tcpc_init(void);

#endif /* !__ASSEMBLER__ */

#endif /* __CROS_EC_BOARD_H */