/* Copyright 2021 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Herobrine board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

#include "baseboard.h"

/* TODO(waihong): Remove the following bringup features */
#define CONFIG_BRINGUP
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */
#define CONFIG_USB_PD_DEBUG_LEVEL 3
#define CONFIG_CMD_GPIO_EXTENDED
#define CONFIG_CMD_POWERINDEBUG
#define CONFIG_I2C_DEBUG

/* Keyboard */
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
#define CONFIG_KEYBOARD_REFRESH_ROW3

#define CONFIG_PWM_KBLIGHT

/* Battery */
#define CONFIG_BATTERY_DEVICE_CHEMISTRY  "LION"
#define CONFIG_BATTERY_REVIVE_DISCONNECT
#define CONFIG_BATTERY_FUEL_GAUGE

/* BC 1.2 Charger */
#define CONFIG_BC12_DETECT_PI3USB9201

/* USB */
#define CONFIG_USB_PD_TCPM_PS8805
#define CONFIG_USBC_PPC_SN5S330
#define CONFIG_USB_PD_PORT_MAX_COUNT 2

/* USB-A */
#define USB_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_DUMB

/* Sensors */
/* BMI260 Base accel/gyro */
#define CONFIG_ACCELGYRO_BMI260
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI260_INT_EVENT \
	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS

/* BMA253 lid accel */
#define CONFIG_ACCEL_BMA255
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)

#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_LID_ANGLE_UPDATE

#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE
#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L

/* GPIO alias */
#define GPIO_AC_PRESENT		GPIO_ACOK_OD
#define GPIO_WP_L		GPIO_EC_WP_ODL
#define GPIO_SWITCHCAP_PG	GPIO_SRC_VPH_PWR_PG
#define GPIO_ACOK_OD		GPIO_CHG_ACOK_OD
#define GPIO_EN_PP5000		GPIO_EN_PP5000_S5
#define GPIO_POWER_GOOD		GPIO_MB_POWER_GOOD
#define GPIO_EC_INT_L		GPIO_AP_EC_INT_L
#define GPIO_DP_HOT_PLUG_DET	GPIO_DP_HOT_PLUG_DET_R

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum adc_channel {
	ADC_VBUS,
	ADC_AMON_BMON,
	ADC_PSYS,
	ADC_CH_COUNT
};

/* Motion sensors */
enum sensor_id {
	LID_ACCEL = 0,
	BASE_ACCEL,
	BASE_GYRO,
	SENSOR_COUNT,
};

enum pwm_channel {
	PWM_CH_KBLIGHT = 0,
	PWM_CH_DISPLIGHT,
	PWM_CH_COUNT
};

/* List of possible batteries */
enum battery_type {
	BATTERY_AP16L5J,
	BATTERY_TYPE_COUNT,
};

/* Reset all TCPCs. */
void board_reset_pd_mcu(void);
void board_set_tcpc_power_mode(int port, int mode);

#endif /* !defined(__ASSEMBLER__) */

#endif /* __CROS_EC_BOARD_H */