/* Copyright 2020 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Volteer board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

/* Baseboard features */
#include "baseboard.h"

#undef CONFIG_CHIP_INIT_ROM_REGION

#define CONFIG_VBOOT_EFS2

#define CONFIG_POWER_BUTTON

#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096

/* LED defines */
#define CONFIG_LED_ONOFF_STATES

/* Keyboard features */

/* Sensors */
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
#define CONFIG_ACCEL_LIS2DE /* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */

/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)

#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL

#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)

/* USB Type C and USB PD defines */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2

#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */

/*
 * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C
 * cables only support up to 60W.
 */
#define PD_OPERATING_POWER_MW 15000
#define PD_MAX_POWER_MW 45000
#define PD_MAX_CURRENT_MA 3000
#define PD_MAX_VOLTAGE_MV 20000

#undef CONFIG_USB_MUX_RUNTIME_CONFIG

/* USB Type A Features */
#define USB_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_DUMB

/* USBC PPC*/
#define CONFIG_USBC_PPC_SN5S330 /* USBC port C0 */
#define CONFIG_USBC_PPC_SYV682X /* USBC port C1 */

/* BC 1.2 */

/* Volume Button feature */

/* Fan features */

/* charger defines */
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10

/* Retimer */
#undef CONFIG_USBC_RETIMER_INTEL_BB
#undef CONFIG_USBC_RETIMER_INTEL_BB_RUNTIME_CONFIG

/* EC console commands */
#define CONFIG_CMD_TCPC_DUMP

/*
 * Macros for GPIO signals used in common code that don't match the
 * schematic names. Signal names in gpio.inc match the schematic and are
 * then redefined here to so it's more clear which signal is being used for
 * which purpose.
 */
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL
#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
#define GPIO_LID_OPEN GPIO_EC_LID_OPEN
#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV
#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE
#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL
#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL
#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL
#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST
#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL
#define GPIO_WP_L GPIO_EC_WP_L
#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_MUTE_BTN_ODL

/* I2C Bus Configuration */
#define CONFIG_I2C
#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED
#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0
#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0
#define I2C_PORT_LIGHTBAR NPCX_I2C_PORT3_0
#define I2C_PORT_POWER NPCX_I2C_PORT5_0
#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0

#define I2C_PORT_BATTERY I2C_PORT_POWER
#define I2C_PORT_CHARGER I2C_PORT_EEPROM

#define I2C_ADDR_EEPROM_FLAGS 0x50
#define CONFIG_I2C_CONTROLLER

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum battery_type {
	BATTERY_SMP,
	BATTERY_LGC,
	BATTERY_SUNWODA,
	BATTERY_TYPE_COUNT,
};

enum pwm_channel {
	PWM_CH_LED4_SIDESEL = 0,
	PWM_CH_FAN,
	PWM_CH_KBLIGHT,
	PWM_CH_COUNT
};

enum sensor_id {
	LID_ACCEL = 0,
	BASE_ACCEL,
	BASE_GYRO,
	SENSOR_COUNT,
};

enum usbc_port { USBC_PORT_C0 = 0, USBC_PORT_C1, USBC_PORT_COUNT };

void board_reset_pd_mcu(void);

#endif /* !__ASSEMBLER__ */

#endif /* __CROS_EC_BOARD_H */