/* Copyright 2016 The ChromiumOS Authors * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ /* Configuration for Scarlet */ #ifndef __CROS_EC_BOARD_H #define __CROS_EC_BOARD_H /* Free up flash space */ #define CONFIG_DEBUG_ASSERT_BRIEF #define CONFIG_LTO #define CONFIG_USB_PD_DEBUG_LEVEL 0 /* Optional modules */ #define CONFIG_ADC #undef CONFIG_ADC_WATCHDOG #define CONFIG_CHIPSET_RK3399 #define CONFIG_CMD_ACCELS #define CONFIG_CMD_RTC #define CONFIG_EMULATED_SYSRQ #undef CONFIG_HIBERNATE #define CONFIG_HOSTCMD_RTC #define CONFIG_I2C #define CONFIG_I2C_CONTROLLER #define CONFIG_I2C_VIRTUAL_BATTERY #define CONFIG_I2C_PASSTHRU_RESTRICTED #define CONFIG_LED_COMMON #define CONFIG_LOW_POWER_IDLE #define CONFIG_LOW_POWER_IDLE_LIMITED #define CONFIG_POWER_COMMON #define CONFIG_SPI #define CONFIG_SPI_CONTROLLER /* Source RTCCLK from external 32.768kHz source on PC15/OSC32_IN. */ #define CONFIG_STM32_CLOCK_LSE #define CONFIG_SWITCH #define CONFIG_WATCHDOG_HELP #define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands for testing */ #undef CONFIG_UART_CONSOLE #define CONFIG_UART_CONSOLE 1 #define CONFIG_UART_RX_DMA /* Enable a different power-on sequence than the one on gru */ #undef CONFIG_CHIPSET_POWER_SEQ_VERSION #define CONFIG_CHIPSET_POWER_SEQ_VERSION 1 /* Optional features */ #define CONFIG_BOARD_PRE_INIT #define CONFIG_BUTTON_TRIGGERED_RECOVERY #define CONFIG_CHARGER_ILIM_PIN_DISABLED #define CONFIG_FORCE_CONSOLE_RESUME #define CONFIG_HOST_COMMAND_STATUS /* Required for FAFT */ #define CONFIG_CMD_BUTTON /* By default, set hcdebug to off */ #undef CONFIG_HOSTCMD_DEBUG_MODE #define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF #undef CONFIG_LID_SWITCH #define CONFIG_POWER_BUTTON #define CONFIG_POWER_BUTTON_IGNORE_LID #define CONFIG_POWER_TRACK_HOST_SLEEP_STATE #define CONFIG_VBOOT_HASH #define CONFIG_VOLUME_BUTTONS #define CONFIG_CHARGER #define CONFIG_CHARGER_RT9467 #define CONFIG_CHARGER_DEFAULT_CURRENT_LIMIT 512 #define CONFIG_CHARGER_MIN_INPUT_CURRENT_LIMIT 512 #define CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT 2 #define CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW 15000 #define CONFIG_CHARGER_PROFILE_OVERRIDE #define CONFIG_CHARGER_DISCHARGE_ON_AC #define CONFIG_CHARGER_OTG #define CONFIG_USB_CHARGER #define CONFIG_USB_MUX_VIRTUAL /* Increase tx buffer size, as we'd like to stream EC log to AP. */ #undef CONFIG_UART_TX_BUF_SIZE #define CONFIG_UART_TX_BUF_SIZE 4096 /* Motion Sensors */ #define CONFIG_ACCELGYRO_BMI160 #define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) /* Camera VSYNC */ #define CONFIG_SYNC #define CONFIG_SYNC_COMMAND #define CONFIG_SYNC_INT_EVENT TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC) /* To be able to indicate the device is in tablet mode. */ #define CONFIG_TABLET_MODE #define CONFIG_TABLET_MODE_SWITCH /* Enable sensor fifo, must also define the _SIZE and _THRES */ #define CONFIG_ACCEL_FIFO /* FIFO size is in power of 2. */ #define CONFIG_ACCEL_FIFO_SIZE 256 /* Depends on how fast the AP boots and typical ODRs. */ #define CONFIG_ACCEL_FIFO_THRES 10 /* USB PD config */ #define CONFIG_CHARGE_MANAGER #define CONFIG_USB_POWER_DELIVERY #define CONFIG_USB_PD_TCPMV1 #define CONFIG_USB_PD_ALT_MODE #define CONFIG_USB_PD_ALT_MODE_DFP #define CONFIG_USB_PD_DISCHARGE_GPIO #define CONFIG_USB_PD_DUAL_ROLE #define CONFIG_USB_PD_LOGGING #define CONFIG_USB_PD_PORT_MAX_COUNT 1 #define CONFIG_USB_PD_TCPM_FUSB302 #define CONFIG_USB_PD_TCPM_TCPCI #define CONFIG_USB_PD_VBUS_DETECT_TCPC #define CONFIG_USB_PD_5V_CHARGER_CTRL #define CONFIG_USBC_SS_MUX #define CONFIG_USBC_VCONN #define CONFIG_USBC_VCONN_SWAP #define CONFIG_USB_PD_COMM_LOCKED #define CONFIG_BATTERY_CUT_OFF #define CONFIG_BATTERY_PRESENT_CUSTOM #define CONFIG_BATTERY_RETRY_NACK #define CONFIG_BATTERY_REVIVE_DISCONNECT #define CONFIG_BATTERY_MAX17055 /* Disable verbose output in EC pd */ #ifdef SECTION_IS_RO #define CONFIG_CMD_PD_SRCCAPS_REDUCED_SIZE #endif /* Battery parameters for max17055 ModelGauge m5 algorithm. */ #define BATTERY_MAX17055_RSENSE 5 /* m-ohm */ #define BATTERY_DESIRED_CHARGING_CURRENT 4000 /* mA */ #define CONFIG_THROTTLE_AP_ON_BAT_DISCHG_CURRENT #define BAT_MAX_DISCHG_CURRENT 5000 /* mA */ #define CONFIG_THROTTLE_AP_ON_BAT_VOLTAGE #define BAT_LOW_VOLTAGE_THRESH 3200 /* mV */ #define PD_OPERATING_POWER_MW 15000 #define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) #define PD_MAX_CURRENT_MA 3000 #define PD_MAX_VOLTAGE_MV 12850 #define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ #define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */ /* Timer selection */ #define TIM_CLOCK32 2 #define TIM_WATCHDOG 7 /* 48 MHz SYSCLK clock frequency */ #define CPU_CLOCK 48000000 /* Optional for testing */ #undef CONFIG_PECI #undef CONFIG_PSTORE /* Modules we want to exclude */ #undef CONFIG_CMD_BATTFAKE #undef CONFIG_CMD_FLASH #undef CONFIG_CMD_HASH #undef CONFIG_CMD_I2C_SCAN #undef CONFIG_CMD_MD #undef CONFIG_CMD_POWERINDEBUG #undef CONFIG_CMD_TIMERINFO #define CONFIG_TASK_PROFILING #define I2C_PORT_CHARGER 0 #define I2C_PORT_BATTERY 0 #define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY #define I2C_PORT_TCPC0 1 /* Route sbs host requests to virtual battery driver */ #define VIRTUAL_BATTERY_ADDR_FLAGS 0x0B /* Enable Accel over SPI */ #define CONFIG_SPI_ACCEL_PORT 0 /* The first SPI controller port (SPI2) */ #define CONFIG_MKBP_INPUT_DEVICES #define CONFIG_MKBP_EVENT #define CONFIG_MKBP_USE_GPIO /* Define the host events which are allowed to wakeup AP in S3. */ #define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ (EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON) | \ EC_HOST_EVENT_MASK(EC_HOST_EVENT_RTC)) #ifndef __ASSEMBLER__ enum adc_channel { /* Real ADC channels begin here */ ADC_BOARD_ID = 0, ADC_CH_COUNT }; /* power signal definitions */ enum power_signal { PP1250_S3_PWR_GOOD = 0, PP900_S0_PWR_GOOD, AP_PWR_GOOD, SUSPEND_DEASSERTED, /* Number of signals */ POWER_SIGNAL_COUNT, }; /* Motion sensors */ enum sensor_id { LID_ACCEL = 0, LID_GYRO, VSYNC, SENSOR_COUNT, }; #include "gpio_signal.h" #include "registers.h" void board_reset_pd_mcu(void); int board_get_version(void); #endif /* !__ASSEMBLER__ */ #endif /* __CROS_EC_BOARD_H */