/* -*- mode:c -*- * * Copyright 2020 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ #ifdef SECTION_IS_RO GPIO_INT(USB_DET_PP_CHG, PIN(C, 13), GPIO_INT_BOTH, vbus0_evt) GPIO_INT(USB_DET_PP_DUT, PIN(C, 12), GPIO_INT_BOTH, vbus1_evt) GPIO_INT(STM_FAULT_IRQ_L, PIN(A, 8), GPIO_INT_FALLING, tca_evt) GPIO_INT(DP_HPD, PIN(A, 15), GPIO_INT_BOTH, dp_evt) GPIO_INT(CHGSRV_TCPC_INT_ODL, PIN(C, 0), GPIO_INT_FALLING, tcpc_evt) GPIO_INT(USBH_I2C_BUSY_INT, PIN(C, 9), GPIO_INT_FALLING, hub_evt) GPIO_INT(DUT_PWR_IRQ_ODL, PIN(F, 1), GPIO_INT_FALLING, dut_pwr_evt) #endif /* SECTION_IS_RO */ /* Outputs */ GPIO(HOST_USB_HUB_RESET_L, PIN(D, 2), GPIO_ODR_HIGH) GPIO(FASTBOOT_DUTHUB_MUX_SEL, PIN(B, 5), GPIO_OUT_HIGH) GPIO(SBU_MUX_EN, PIN(B, 6), GPIO_OUT_LOW) GPIO(FASTBOOT_DUTHUB_MUX_EN_L, PIN(B, 7), GPIO_OUT_LOW) /* Power on init has reset asserted, we will pull the hub out of reset * in the board init to help avoid brownout. */ GPIO(DUT_HUB_USB_RESET_L, PIN(B, 9), GPIO_ODR_HIGH) GPIO(ATMEL_HWB_L, PIN(B, 12), GPIO_OUT_HIGH) GPIO(USB3_A1_MUX_EN_L, PIN(F, 0), GPIO_OUT_HIGH) /* Inputs */ /* Type-C */ /* PD RX/TX */ GPIO(USB_C_REF, PIN(A, 1), GPIO_ANALOG) GPIO(USB_CHG_CC1_MCU, PIN(A, 2), GPIO_ANALOG) GPIO(USB_CHG_CC2_MCU, PIN(A, 4), GPIO_ANALOG) GPIO(USB_DUT_CC1_MCU, PIN(A, 0), GPIO_ANALOG) GPIO(USB_DUT_CC2_MCU, PIN(A, 5), GPIO_ANALOG) GPIO(USB_CHG_CC1_TX_DATA, PIN(B, 4), GPIO_INPUT) GPIO(USB_CHG_CC2_TX_DATA, PIN(A, 6), GPIO_INPUT) GPIO(USB_DUT_CC1_TX_DATA, PIN(B, 14), GPIO_INPUT) GPIO(USB_DUT_CC2_TX_DATA, PIN(C, 2), GPIO_INPUT) GPIO(USB_DUT_CC1_RPUSB, PIN(C, 3), GPIO_INPUT) GPIO(USB_DUT_CC1_RD, PIN(C, 6), GPIO_INPUT) GPIO(USB_DUT_CC1_RA, PIN(C, 7), GPIO_INPUT) GPIO(USB_DUT_CC1_RP3A0, PIN(C, 14), GPIO_INPUT) GPIO(USB_DUT_CC1_RP1A5, PIN(C, 15), GPIO_INPUT) GPIO(USB_DUT_CC2_RPUSB, PIN(B, 0), GPIO_INPUT) GPIO(USB_DUT_CC2_RD, PIN(B, 1), GPIO_INPUT) GPIO(USB_DUT_CC2_RA, PIN(B, 2), GPIO_INPUT) GPIO(USB_DUT_CC2_RP1A5, PIN(C, 1), GPIO_INPUT) GPIO(USB_DUT_CC2_RP3A0, PIN(C, 8), GPIO_INPUT) /* Alternate PD functions */ GPIO(USB_CHG_TX_CLKOUT, PIN(B, 8), GPIO_INPUT) GPIO(USB_CHG_TX_CLKIN, PIN(B, 3), GPIO_INPUT) GPIO(USB_DUT_TX_CLKOUT, PIN(B, 15), GPIO_INPUT) GPIO(USB_DUT_TX_CLKIN, PIN(B, 13), GPIO_INPUT) /* I2C pins should be configured as inputs until I2C module is */ /* initialized. This will avoid driving the lines unintentionally.*/ GPIO(MASTER_I2C_SCL, PIN(B, 10), GPIO_INPUT) GPIO(MASTER_I2C_SDA, PIN(B, 11), GPIO_INPUT) /* Unimplemented signals since we are not an EC */ UNIMPLEMENTED(ENTERING_RW) UNIMPLEMENTED(WP_L) ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_USART, 0) /* USART1: PA9/PA10 - Servo DBG UART1 */ ALTERNATE(PIN_MASK(C, 0x0030), 1, MODULE_USART, 0) /* USART3: PC4/PC5 - Servo DUT UART3 */ ALTERNATE(PIN_MASK(C, 0x0C00), 0, MODULE_USART, 0) /* USART4: PC10/PC11 - Servo UART4 */ ALTERNATE(PIN_MASK(B, 0x0C00), 1, MODULE_I2C, GPIO_ODR_HIGH) /* I2C MASTER:PB10/11 */ ALTERNATE(PIN_MASK(B, 0x0008), 0, MODULE_USB_PD, 0) /* SPI1_SCK: PB3 */ ALTERNATE(PIN_MASK(B, 0x2000), 0, MODULE_USB_PD, 0) /* SPI2_SCK: PB13 */ ALTERNATE(PIN_MASK(B, 0x0100), 2, MODULE_USB_PD, 0) /* TIM16_CH1: PB8 */ ALTERNATE(PIN_MASK(B, 0x8000), 1, MODULE_USB_PD, 0) /* TIM15_CH2: PB15 */