/* Copyright 2014 The ChromiumOS Authors
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* USB Power delivery board configuration */

#ifndef __CROS_EC_USB_PD_CONFIG_H
#define __CROS_EC_USB_PD_CONFIG_H

#include "ina2xx.h"

/* Timer selection for baseband PD communication */
#define TIM_CLOCK_PD_TX_C0 17
#define TIM_CLOCK_PD_RX_C0 1

#define TIM_CLOCK_PD_TX(p) TIM_CLOCK_PD_TX_C0
#define TIM_CLOCK_PD_RX(p) TIM_CLOCK_PD_RX_C0

/* TX and RX timer register */
#define TIM_REG_TX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_TX_C0))
#define TIM_REG_RX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_RX_C0))
#define TIM_REG_TX(p) TIM_REG_TX_C0
#define TIM_REG_RX(p) TIM_REG_RX_C0

/* Timer channel */
#define TIM_RX_CCR_C0 1
#define TIM_TX_CCR_C0 1

/* RX timer capture/compare register */
#define TIM_CCR_C0 (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_C0, TIM_RX_CCR_C0))
#define TIM_RX_CCR_REG(p) TIM_CCR_C0

/* use the hardware accelerator for CRC */
#define CONFIG_HW_CRC

/* TX is using SPI1 on PA6/PB4 */
#define SPI_REGS(p) STM32_SPI1_REGS
#define DMAC_SPI_TX(p) STM32_DMAC_CH3

static inline void spi_enable_clock(int port)
{
	STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI1;
}

/* RX is using COMP1 or COMp2 triggering TIM1 CH1  */
#define CMP1OUTSEL STM32_COMP_CMP1OUTSEL_TIM1_IC1
#define CMP2OUTSEL STM32_COMP_CMP2OUTSEL_TIM1_IC1

#define DMAC_TIM_RX(p) STM32_DMAC_CH2
#define TIM_RX_CCR_IDX(p) TIM_RX_CCR_C0
#define TIM_TX_CCR_IDX(p) TIM_TX_CCR_C0
#define TIM_CCR_CS 1
#define EXTI_COMP_MASK(p) (BIT(21) | BIT(22))
#define IRQ_COMP STM32_IRQ_COMP
/* triggers packet detection on comparator falling edge */
#define EXTI_XTSR STM32_EXTI_FTSR

/* the pins used for communication need to be hi-speed */
static inline void pd_set_pins_speed(int port)
{
	/* 40 MHz pin speed on SPI TX PB4 */
	STM32_GPIO_OSPEEDR(GPIO_B) |= 0x00000300;
	/* 40 MHz pin speed on SPI TX PA6 */
	STM32_GPIO_OSPEEDR(GPIO_A) |= 0x00003000;
	/* 40 MHz pin speed on TIM17_CH1 (PB9) */
	STM32_GPIO_OSPEEDR(GPIO_B) |= 0x000C0000;
}

/* Reset SPI peripheral used for TX */
static inline void pd_tx_spi_reset(int port)
{
	/* Reset SPI1 */
	STM32_RCC_APB2RSTR |= BIT(12);
	STM32_RCC_APB2RSTR &= ~BIT(12);
}

/* Drive the CC line from the TX block */
static inline void pd_tx_enable(int port, int polarity)
{
#if 0 /* Transmit only on the active CC line */
	if (polarity) {
		gpio_set_level(GPIO_CC2_TX_EN, 1);
		/* TX_DATA on PA6 is now connected to SPI1 */
		gpio_set_alternate_function(GPIO_A, 0x0040, 0);
	} else {
		gpio_set_level(GPIO_CC1_TX_EN, 1);
		/* TX_DATA on PB4 is now connected to SPI1 */
		gpio_set_alternate_function(GPIO_B, 0x0010, 0);
	}
#else /* Transmit on both CC lines */
	gpio_set_level(GPIO_CC2_TX_EN, 1);
	gpio_set_level(GPIO_CC1_TX_EN, 1);
	/* TX_DATA on PA6 is now connected to SPI1 */
	gpio_set_alternate_function(GPIO_A, 0x0040, 0);
	/* TX_DATA on PB4 is now connected to SPI1 */
	gpio_set_alternate_function(GPIO_B, 0x0010, 0);
#endif
}

/* Put the TX driver in Hi-Z state */
static inline void pd_tx_disable(int port, int polarity)
{
	/* TX_DATA on PB4 is an output low GPIO to disable the FET */
	STM32_GPIO_MODER(GPIO_B) =
		(STM32_GPIO_MODER(GPIO_B) & ~(3 << (2 * 4))) | (1 << (2 * 4));
	/* TX_DATA on PA6 is an output low GPIO to disable the FET */
	STM32_GPIO_MODER(GPIO_A) =
		(STM32_GPIO_MODER(GPIO_A) & ~(3 << (2 * 6))) | (1 << (2 * 6));
	/*
	 * Tri-state the low side after the high side
	 * to ensure we are not going above Vnc
	 */
	gpio_set_level(GPIO_CC1_TX_EN, 0);
	gpio_set_level(GPIO_CC2_TX_EN, 0);
}

/* we know the plug polarity, do the right configuration */
static inline void pd_select_polarity(int port, int polarity)
{
	/* use the right comparator */
	STM32_COMP_CSR =
		(STM32_COMP_CSR &
		 ~(STM32_COMP_CMP1INSEL_MASK | STM32_COMP_CMP2INSEL_MASK |
		   STM32_COMP_CMP1EN | STM32_COMP_CMP2EN)) |
		STM32_COMP_CMP1INSEL_INM4 | STM32_COMP_CMP2INSEL_INM4 |
		(polarity ? STM32_COMP_CMP2EN : STM32_COMP_CMP1EN);
}

/* Initialize pins used for clocking */
static inline void pd_tx_init(void)
{
	gpio_config_module(MODULE_USB_PD, 1);

#ifndef CONFIG_USB_PD_TX_PHY_ONLY
	/* Detect when VBUS crosses the 4.5V threshold (1.25mV/bit) */
	ina2xx_write(0, INA2XX_REG_ALERT, 4500 * 100 / 125);
	ina2xx_write(0, INA2XX_REG_MASK, INA2XX_MASK_EN_BOL);
	/* start as a power consumer */
	gpio_set_level(GPIO_CC1_RD, 0);
	gpio_set_level(GPIO_CC2_RD, 0);
#endif /* CONFIG_USB_PD_TX_PHY_ONLY */
}

static inline void pd_set_host_mode(int port, int enable)
{
	if (enable) {
		gpio_set_level(GPIO_CC1_RD, 1);
		gpio_set_level(GPIO_CC2_RD, 1);
		/* set Rp by driving high RPUSB GPIO */
		gpio_set_flags(GPIO_CC1_RPUSB, GPIO_OUT_HIGH);
		gpio_set_flags(GPIO_CC2_RPUSB, GPIO_OUT_HIGH);
	} else {
		/* put back RPUSB GPIO in the default state and set Rd */
		gpio_set_flags(GPIO_CC1_RPUSB, GPIO_ODR_HIGH);
		gpio_set_flags(GPIO_CC2_RPUSB, GPIO_ODR_HIGH);
		gpio_set_level(GPIO_CC1_RD, 0);
		gpio_set_level(GPIO_CC2_RD, 0);
	}
}

static inline void pd_config_init(int port, uint8_t power_role)
{
#ifndef CONFIG_USB_PD_TX_PHY_ONLY
	/* Set CC pull resistors */
	pd_set_host_mode(port, power_role);
#endif /* CONFIG_USB_PD_TX_PHY_ONLY */

	/* Initialize TX pins and put them in Hi-Z */
	pd_tx_init();
}

static inline int pd_adc_read(int port, int cc)
{
	if (cc == 0)
		return adc_read_channel(ADC_CH_CC1_PD);
	else
		return adc_read_channel(ADC_CH_CC2_PD);
}

#endif /* __CROS_EC_USB_PD_CONFIG_H */