/* Copyright 2020 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Waddledee board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

/* Select Baseboard features */
#define VARIANT_DEDEDE_EC_IT8320
#include "baseboard.h"

/* System unlocked in early development */
#define CONFIG_SYSTEM_UNLOCKED

#define CONFIG_CMD_CHARGER_DUMP

/* Battery */
#define CONFIG_BATTERY_FUEL_GAUGE

/* BC 1.2 */
#define CONFIG_BC12_DETECT_PI3USB9201

/* Charger */
#define CONFIG_CHARGER_SM5803		/* C0 and C1: Charger */
#define CONFIG_USB_PD_VBUS_DETECT_CHARGER
#define CONFIG_USB_PD_5V_CHARGER_CTRL
#define CONFIG_CHARGER_OTG
#undef  CONFIG_CHARGER_SINGLE_CHIP
#define CONFIG_OCPC
#define CONFIG_OCPC_DEF_RBATT_MOHMS 21 /* R_DS(on) 10.7mOhm + 10mOhm sns rstr */

/*
 * GPIO for C1 interrupts, for baseboard use
 *
 * Note this will only be valid for board revision 1
 */
#define GPIO_USB_C1_INT_ODL GPIO_USB_C1_INT_V1_ODL

/* LED */
#define CONFIG_LED_PWM
#define CONFIG_LED_PWM_COUNT 1

/* PWM */
#define CONFIG_PWM

/* Sensors */
#define CONFIG_ACCEL_KX022		/* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM	/* Base accel */
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)

#define CONFIG_ACCEL_INTERRUPTS
/* Enable sensor fifo, must also define the _SIZE and _THRES */
#define CONFIG_ACCEL_FIFO
/* Power of 2 - Too large of a fifo causes too much timestamp jitter */
#define CONFIG_ACCEL_FIFO_SIZE 256
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)

#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL

#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE

/* TCPC */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP	/* C0: ITE EC TCPC */
#define CONFIG_USB_PD_TCPM_ANX7447	/* C1: ANX TCPC + Mux */
#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 1

/* Thermistors */
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B

/* USB Mux and Retimer */
#define CONFIG_USB_MUX_IT5205			/* C1: ITE Mux */
#define I2C_PORT_USB_MUX I2C_PORT_USB_C0	/* Required for ITE Mux */

#define CONFIG_USBC_RETIMER_TUSB544		/* C1 Redriver: TUSB544 */

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum chg_id {
	CHARGER_PRIMARY,
	CHARGER_SECONDARY,
	CHARGER_NUM,
};

enum pwm_channel {
	PWM_CH_KBLIGHT,
	PWM_CH_LED_RED,
	PWM_CH_LED_GREEN,
	PWM_CH_LED_BLUE,
	PWM_CH_COUNT,
};

/* Motion sensors */
enum sensor_id {
	LID_ACCEL,
	BASE_ACCEL,
	BASE_GYRO,
	SENSOR_COUNT
};

/* ADC channels */
enum adc_channel {
	ADC_VSNS_PP3300_A,     /* ADC0 */
	ADC_TEMP_SENSOR_1,     /* ADC2 */
	ADC_TEMP_SENSOR_2,     /* ADC3 */
	ADC_SUB_ANALOG,        /* ADC13 */
	ADC_CH_COUNT
};

enum temp_sensor_id {
	TEMP_SENSOR_1,
	TEMP_SENSOR_2,
	TEMP_SENSOR_COUNT
};

/* List of possible batteries */
enum battery_type {
	BATTERY_LGC15,
	BATTERY_PANASONIC_AP15O5L,
	BATTERY_SANYO,
	BATTERY_SONY,
	BATTERY_SMP_AP13J7K,
	BATTERY_PANASONIC_AC15A3J,
	BATTERY_LGC_AP18C8K,
	BATTERY_MURATA_AP18C4K,
	BATTERY_LGC_AP19A8K,
	BATTERY_LGC_G023,
	BATTERY_TYPE_COUNT,
};

#endif /* !__ASSEMBLER__ */

#endif /* __CROS_EC_BOARD_H */