/* Copyright 2020 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Waddledoo board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

#define VARIANT_DEDEDE_EC_NPCX796FC
#include "baseboard.h"

/*
 * Keep the system unlocked in early development.
 * TODO(b/151264302): Make sure to remove this before production!
 */
#define CONFIG_SYSTEM_UNLOCKED

/* Charger */
#define CONFIG_CHARGER_DISCHARGE_ON_AC
#define CONFIG_CHARGER_RAA489000
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_OCPC_DEF_RBATT_MOHMS 22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr */
#define CONFIG_OCPC
#undef  CONFIG_CHARGER_SINGLE_CHIP

/* EC console commands */
#define CONFIG_CMD_TCPC_DUMP
#define CONFIG_CMD_CHARGER_DUMP

/* Keyboard */
#define CONFIG_PWM_KBLIGHT

/* LED */
#define CONFIG_LED_PWM
#define CONFIG_LED_PWM_COUNT 1
#undef CONFIG_LED_PWM_NEAR_FULL_COLOR
#undef CONFIG_LED_PWM_SOC_ON_COLOR
#undef CONFIG_LED_PWM_SOC_SUSPEND_COLOR
#undef CONFIG_LED_PWM_LOW_BATT_COLOR
#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE
#define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_WHITE
#define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_WHITE
#define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER

/* USB */
#define CONFIG_BC12_DETECT_PI3USB9201
#define CONFIG_USBC_RETIMER_NB7V904M

/* USB PD */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_TCPM_RAA489000

/* USB defines specific to external TCPCs */
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_TCPC_LOW_POWER

/* Variant references the TCPCs to determine Vbus sourcing */
#define CONFIG_USB_PD_5V_EN_CUSTOM

/* I2C configuration */
#define I2C_PORT_EEPROM     NPCX_I2C_PORT7_0
#define I2C_PORT_BATTERY    NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR     NPCX_I2C_PORT0_0
#define I2C_PORT_USB_C0     NPCX_I2C_PORT1_0
#define I2C_PORT_SUB_USB_C1 NPCX_I2C_PORT2_0
#define I2C_PORT_USB_MUX    I2C_PORT_USB_C0
/* TODO(b:147440290): Need to handle multiple charger ICs */
#define I2C_PORT_CHARGER    I2C_PORT_USB_C0

#define I2C_PORT_ACCEL      I2C_PORT_SENSOR

#define I2C_ADDR_EEPROM_FLAGS 0x50 /* 7b address */

/*
 * I2C pin names for baseboard
 *
 * Note: these lines will be set as i2c on start-up, but this should be
 * okay since they're ODL.
 */
#define GPIO_EC_I2C_SUB_USB_C1_SCL GPIO_EC_I2C_SUB_C1_SCL_HDMI_EN_ODL
#define GPIO_EC_I2C_SUB_USB_C1_SDA GPIO_EC_I2C_SUB_C1_SDA_HDMI_HPD_ODL

/* Sensors */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO

#define CONFIG_ACCEL_BMA255		/* Lid accel */
#define CONFIG_ACCELGYRO_BMI160		/* Base accel */
#define CONFIG_SYNC			/* Camera VSYNC */

/* Lid operates in forced mode, base in FIFO */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_ACCEL_FIFO
#define CONFIG_ACCEL_FIFO_SIZE 256	/* Must be a power of 2 */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)

#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define CONFIG_SYNC_INT_EVENT TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC)

#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL

#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE

#define CONFIG_MKBP_EVENT
#define CONFIG_MKBP_USE_GPIO

/* Thermistors */
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_PP3300_A

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum chg_id {
	CHARGER_PRIMARY,
	CHARGER_SECONDARY,
	CHARGER_NUM,
};

enum adc_channel {
	ADC_TEMP_SENSOR_1,     /* ADC0 */
	ADC_TEMP_SENSOR_2,     /* ADC1 */
	ADC_SUB_ANALOG,	       /* ADC2 */
	ADC_VSNS_PP3300_A,     /* ADC9 */
	ADC_CH_COUNT
};

enum sensor_id {
	LID_ACCEL,
	BASE_ACCEL,
	BASE_GYRO,
	VSYNC,
	SENSOR_COUNT
};

enum pwm_channel {
	PWM_CH_KBLIGHT,
	PWM_CH_LED1_AMBER,
	PWM_CH_LED2_WHITE,
	PWM_CH_COUNT,
};

enum temp_sensor_id {
	TEMP_SENSOR_1,
	TEMP_SENSOR_2,
	TEMP_SENSOR_COUNT
};

int board_is_sourcing_vbus(int port);

#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */