1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
|
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Shared USB-C policy for Grunt boards */
#include "charge_manager.h"
#include "common.h"
#include "compile_time_macros.h"
#include "console.h"
#include "ec_commands.h"
#include "gpio.h"
#include "system.h"
#include "usb_mux.h"
#include "usb_pd.h"
#include "usbc_ppc.h"
#include "util.h"
#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args)
#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args)
#define PDO_FIXED_FLAGS (PDO_FIXED_DUAL_ROLE | PDO_FIXED_DATA_SWAP |\
PDO_FIXED_COMM_CAP)
int pd_check_vconn_swap(int port)
{
/* in G3, do not allow vconn swap since 5V rail is off */
return gpio_get_level(GPIO_S5_PGOOD);
}
void pd_power_supply_reset(int port)
{
int prev_en;
prev_en = ppc_is_sourcing_vbus(port);
/* Disable VBUS. */
ppc_vbus_source_enable(port, 0);
/* Enable discharge if we were previously sourcing 5V */
if (prev_en)
pd_set_vbus_discharge(port, 1);
/* Notify host of power info change. */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
}
int pd_set_power_supply_ready(int port)
{
int rv;
/* Disable charging. */
rv = ppc_vbus_sink_enable(port, 0);
if (rv)
return rv;
pd_set_vbus_discharge(port, 0);
/* Provide Vbus. */
rv = ppc_vbus_source_enable(port, 1);
if (rv)
return rv;
/* Notify host of power info change. */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
return EC_SUCCESS;
}
int pd_snk_is_vbus_provided(int port)
{
return ppc_is_vbus_present(port);
}
int board_vbus_source_enabled(int port)
{
return ppc_is_sourcing_vbus(port);
}
/* ----------------- Vendor Defined Messages ------------------ */
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
mux_state_t svdm_dp_mux_mode(int port)
{
int mf_pref = PD_VDO_DPSTS_MF_PREF(dp_status[port]);
int pin_mode = pd_dfp_dp_get_pin_mode(port, dp_status[port]);
/*
* Multi-function operation is only allowed if that pin config is
* supported.
*/
if ((pin_mode & MODE_DP_PIN_MF_MASK) && mf_pref)
return USB_PD_MUX_DOCK;
else
return USB_PD_MUX_DP_ENABLED;
}
__override int svdm_dp_config(int port, uint32_t *payload)
{
int opos = pd_alt_mode(port, TCPCI_MSG_SOP, USB_SID_DISPLAYPORT);
int mf_pref = PD_VDO_DPSTS_MF_PREF(dp_status[port]);
int pin_mode = pd_dfp_dp_get_pin_mode(port, dp_status[port]);
mux_state_t mux_mode = svdm_dp_mux_mode(port);
if (!pin_mode)
return 0;
CPRINTS("pin_mode: %x, mf: %d, mux: %d", pin_mode, mf_pref, mux_mode);
/*
* Place the USB Type-C pins that are to be re-configured to DisplayPort
* Configuration into the Safe state. For USB_PD_MUX_DOCK, the
* superspeed signals can remain connected. For USB_PD_MUX_DP_ENABLED,
* disconnect the superspeed signals here, before the pins are
* re-configured to DisplayPort (in svdm_dp_post_config, when we receive
* the config ack).
*/
if (mux_mode == USB_PD_MUX_DP_ENABLED)
usb_mux_set(port, USB_PD_MUX_NONE, USB_SWITCH_CONNECT,
polarity_rm_dts(pd_get_polarity(port)));
payload[0] = VDO(USB_SID_DISPLAYPORT, 1,
CMD_DP_CONFIG | VDO_OPOS(opos));
payload[1] = VDO_DP_CFG(pin_mode, /* pin mode */
1, /* DPv1.3 signaling */
2); /* UFP connected */
return 2;
};
#define PORT_TO_HPD(port) ((port) ? GPIO_USB_C1_DP_HPD : GPIO_USB_C0_DP_HPD)
__override void svdm_dp_post_config(int port)
{
/* Connect the SBU and USB lines to the connector. */
ppc_set_sbu(port, 1);
usb_mux_set(port, svdm_dp_mux_mode(port), USB_SWITCH_CONNECT,
polarity_rm_dts(pd_get_polarity(port)));
dp_flags[port] |= DP_FLAGS_DP_ON;
if (!(dp_flags[port] & DP_FLAGS_HPD_HI_PENDING))
return;
gpio_set_level(PORT_TO_HPD(port), 1);
/* set the minimum time delay (2ms) for the next HPD IRQ */
svdm_hpd_deadline[port] = get_time().val + HPD_USTREAM_DEBOUNCE_LVL;
usb_mux_hpd_update(port, USB_PD_MUX_HPD_LVL |
USB_PD_MUX_HPD_IRQ_DEASSERTED);
}
#endif /* CONFIG_USB_PD_ALT_MODE_DFP */
|
