path: root/baseboard/mancomb/baseboard.h

/* Copyright 2021 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Mancomb baseboard configuration */

#ifndef __CROS_EC_BASEBOARD_H
#define __CROS_EC_BASEBOARD_H

/* NPCX9 config */
#define CONFIG_PORT80_4_BYTE
#define NPCX9_PWM1_SEL    1  /* GPIO C2 is used as PWM1. */
#define NPCX_UART_MODULE2 1  /* GPIO64/65 are used as UART pins. */

/* Optional features */
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */
#define CONFIG_LTO /* Link-Time Optimizations to reduce code size */
#define CONFIG_I2C_DEBUG /* Print i2c traces */

#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096

/* Vboot Config */
#define CONFIG_CRC8
#define CONFIG_VBOOT_EFS2
#define CONFIG_VBOOT_HASH
#define CONFIG_VSTORE
#define CONFIG_VSTORE_SLOT_COUNT 1
#define GPIO_PACKET_MODE_EN	GPIO_EC_GSC_PACKET_MODE

/* CBI Config */
#define CONFIG_CROS_BOARD_INFO
#define CONFIG_BOARD_VERSION_CBI

/* Undefs because Box */
#undef CONFIG_LID_SWITCH
#undef CONFIG_HIBERNATE
#undef CONFIG_KEYBOARD_BOOT_KEYS
#undef CONFIG_KEYBOARD_PRINT_SCAN_TIMES

/* Power Config */
#define CONFIG_CHIPSET_X86_RSMRST_DELAY
#define CONFIG_DEDICATED_RECOVERY_BUTTON
#define CONFIG_DEDICATED_RECOVERY_BUTTON_2
#undef  CONFIG_EXTPOWER_DEBOUNCE_MS
#define CONFIG_EXTPOWER_DEBOUNCE_MS 16
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_POWER_BUTTON
#define CONFIG_POWER_BUTTON_IGNORE_LID
#define CONFIG_POWER_BUTTON_INIT_IDLE
#define CONFIG_POWER_BUTTON_TO_PCH_CUSTOM
#define CONFIG_POWER_BUTTON_X86
#define CONFIG_POWER_COMMON
#define CONFIG_POWER_S0IX
#define CONFIG_POWER_SLEEP_FAILURE_DETECTION
#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE
#define G3_TO_PWRBTN_DELAY_MS 80
#define GPIO_EN_PWR_A		GPIO_EN_PWR_S5
#define GPIO_PCH_PWRBTN_L	GPIO_EC_SOC_PWR_BTN_L
#define GPIO_PCH_RSMRST_L	GPIO_EC_SOC_RSMRST_L
#define GPIO_PCH_SLP_S0_L	GPIO_SLP_S3_S0I3_L
#define GPIO_PCH_SLP_S3_L	GPIO_SLP_S3_L
#define GPIO_PCH_SLP_S5_L	GPIO_SLP_S5_L
#define GPIO_PCH_SYS_PWROK	GPIO_EC_SOC_PWR_GOOD
#define GPIO_PCH_WAKE_L		GPIO_EC_SOC_WAKE_L
#define GPIO_POWER_BUTTON_L	GPIO_MECH_PWR_BTN_ODL
#define GPIO_RECOVERY_L         GPIO_EC_RECOVERY_BTN_ODL
#define GPIO_RECOVERY_L_2       GPIO_GSC_EC_RECOVERY_BTN_ODL
#define GPIO_S0_PGOOD		GPIO_PG_PCORE_S0_R_OD
#define GPIO_S5_PGOOD		GPIO_PG_PWR_S5
#define GPIO_SYS_RESET_L	GPIO_EC_SYS_RST_L
#define SAFE_RESET_VBUS_DELAY_MS 900
#define SAFE_RESET_VBUS_MV 5000

/*
 * On power-on, H1 releases the EC from reset but then quickly asserts and
 * releases the reset a second time. This means the EC sees 2 resets:
 * (1) power-on reset, (2) reset-pin reset. This config will
 * allow the second reset to be treated as a power-on.
 */
#define CONFIG_BOARD_RESET_AFTER_POWER_ON

/* Thermal Config */
#define CONFIG_ADC
#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B
#define CONFIG_THROTTLE_AP
#define CONFIG_TEMP_SENSOR_SB_TSI
#define CONFIG_THERMISTOR
#define CONFIG_CPU_PROCHOT_ACTIVE_LOW
#define GPIO_CPU_PROCHOT	GPIO_PROCHOT_ODL
#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_PWR_S5

/* Flash Config */
/* See config_chip-npcx9.h for SPI flash configuration */
#undef CONFIG_SPI_FLASH /* Don't enable external flash interface */
#define GPIO_WP_L			GPIO_EC_WP_L

/* Host communication */
#define CONFIG_CMD_CHARGEN
#define CONFIG_HOSTCMD_ESPI
#define CONFIG_MKBP_EVENT
#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT
#define GPIO_EC_INT_L		GPIO_EC_SOC_INT_L

/* Chipset config */
#define CONFIG_CHIPSET_CEZANNE
#define CONFIG_CHIPSET_CAN_THROTTLE
#define CONFIG_CHIPSET_RESET_HOOK

/* Charger Config */
#define CONFIG_CHARGE_MANAGER
#undef  CONFIG_CHARGE_MANAGER_SAFE_MODE
#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 50000
#define ADC_VBUS SNS_PPVAR_PWR_IN

/* Dedicated barreljack charger port */
#undef  CONFIG_DEDICATED_CHARGE_PORT_COUNT
#define CONFIG_DEDICATED_CHARGE_PORT_COUNT 1
#define DEDICATED_CHARGE_PORT CONFIG_USB_PD_PORT_MAX_COUNT

/* USB Type C and USB PD config */
#define CONFIG_USB_PD_REV30
#define CONFIG_USB_PD_TCPMV2
#define CONFIG_USB_PD_DECODE_SOP
#define CONFIG_USB_DRP_ACC_TRYSRC
/* TODO: Enable TCPMv2 Fast Role Swap (FRS) */
#define CONFIG_HOSTCMD_PD_CONTROL
#define CONFIG_CMD_TCPC_DUMP
#define CONFIG_USB_CHARGER
#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_USB_PD_ALT_MODE
#define CONFIG_USB_PD_ALT_MODE_DFP
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_DP_HPD_GPIO
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_LOGGING
#define CONFIG_USB_PD_TCPC_LOW_POWER
#undef  CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE
#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC)
#define CONFIG_USB_PD_TCPM_MUX
#define CONFIG_USB_PD_TCPM_NCT38XX
#define CONFIG_USB_PD_TCPM_TCPCI
#define CONFIG_USB_PD_TRY_SRC
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USBC_PPC
#define CONFIG_USBC_PPC_SBU
#define CONFIG_USBC_PPC_AOZ1380
#define CONFIG_USBC_RETIMER_PI3HDX1204
#define CONFIG_USBC_SS_MUX
#define CONFIG_USBC_SS_MUX_DFP_ONLY
#define CONFIG_USBC_VCONN
#define CONFIG_USBC_VCONN_SWAP
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USBC_PPC_NX20P3483
#define CONFIG_USBC_RETIMER_PS8818
#define CONFIG_USB_MUX_AMD_FP6

#define GPIO_USB_C0_DP_HPD GPIO_USB_C0_HPD
#define GPIO_USB_C1_DP_HPD GPIO_USB_C1_HPD

#define CONFIG_IO_EXPANDER
#define CONFIG_IO_EXPANDER_NCT38XX
#define CONFIG_IO_EXPANDER_PORT_COUNT USBC_PORT_COUNT

#define PD_POWER_SUPPLY_TURN_ON_DELAY	30000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY	30000 /* us */

#define PD_OPERATING_POWER_MW	CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON
#define PD_MAX_CURRENT_MA	5000
#define PD_MAX_VOLTAGE_MV	20000
/* Max Power = 100 W */
#define PD_MAX_POWER_MW		((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000)

/* USB-A config */
#define USB_PORT_COUNT USBA_PORT_COUNT
#define CONFIG_USB_PORT_POWER_SMART
#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP
#define CONFIG_USB_PORT_POWER_SMART_INVERTED

#define GPIO_USB1_ILIM_SEL IOEX_USB_A0_LIMIT_SDP
#define GPIO_USB2_ILIM_SEL IOEX_USB_A1_LIMIT_SDP

/* Round up 3250 max current to multiple of 128mA for ISL9241 AC prochot. */
#define MANCOMB_AC_PROCHOT_CURRENT_MA 3328

/*
 * USB ID - This is allocated specifically for Mancomb
 */
#define CONFIG_USB_PID 0x504D

/* BC 1.2 */
/*
 * For legacy BC1.2 charging with CONFIG_CHARGE_RAMP_SW, ramp up input current
 * until voltage drops to 4.5V. Don't go lower than this to be kind to the
 * charger (see b/67964166).
 */
#define BC12_MIN_VOLTAGE 4500
#define CONFIG_BC12_DETECT_PI3USB9201

/* I2C Bus Configuration */
#define CONFIG_I2C
#define CONFIG_I2C_CONTROLLER
#define CONFIG_I2C_UPDATE_IF_CHANGED
#define I2C_PORT_TCPC0		NPCX_I2C_PORT0_0
#define I2C_PORT_TCPC1		NPCX_I2C_PORT1_0
#define I2C_PORT_USB_HUB	NPCX_I2C_PORT2_0
#define I2C_PORT_USB_MUX	NPCX_I2C_PORT3_0
#define I2C_PORT_POWER		NPCX_I2C_PORT4_1
#define I2C_PORT_EEPROM		NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR		NPCX_I2C_PORT6_1
#define I2C_PORT_THERMAL_AP	NPCX_I2C_PORT7_0
#define I2C_ADDR_EEPROM_FLAGS	0x50

/* Fan Config */
#define CONFIG_FANS FAN_CH_COUNT
/* TODO: Set CONFIG_FAN_INIT_SPEED, defaults to 100 */

/* LED Config */
#define CONFIG_PWM

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

/* Power input signals */
enum power_signal {
	X86_SLP_S0_N,		/* SOC  -> SLP_S3_S0I3_L */
	X86_SLP_S3_N,		/* SOC  -> SLP_S3_L */
	X86_SLP_S5_N,		/* SOC  -> SLP_S5_L */

	X86_S0_PGOOD,		/* PMIC -> S0_PWROK_OD */
	X86_S5_PGOOD,		/* PMIC -> S5_PWROK */

	/* Number of X86 signals */
	POWER_SIGNAL_COUNT,
};

/* USB-C ports */
enum usbc_port {
	USBC_PORT_C0 = 0,
	USBC_PORT_C1,
	USBC_PORT_COUNT
};

enum charge_port {
	CHARGE_PORT_TYPEC0,
	CHARGE_PORT_TYPEC1,
	CHARGE_PORT_BARRELJACK,
	CHARGE_PORT_COUNT
};

/*
 * USB-A ports
 * Port A1-A4 are controlled by the USB HUB
 */
enum usba_port {
	USBA_PORT_A0 = 0,
	USBA_PORT_A1,
	USBA_PORT_A2,
	USBA_PORT_A3,
	USBA_PORT_A4,
	USBA_PORT_COUNT
};

/* ADC Channels */
enum adc_channel {
	ADC_TEMP_SENSOR_SOC = 0,
	ANALOG_PPVAR_PWR_IN_IMON,
	ADC_TEMP_SENSOR_MEMORY,
	SNS_PPVAR_PWR_IN,
	ADC_TEMP_SENSOR_AMBIENT,
	ADC_CH_COUNT
};

/* Temp Sensors */
enum temp_sensor_id {
	TEMP_SENSOR_SOC = 0,
	TEMP_SENSOR_MEMORY,
	TEMP_SENSOR_AMBIENT,
	TEMP_SENSOR_CPU,
	TEMP_SENSOR_COUNT
};

/* PWM Channels */
enum pwm_channel {
	PWM_CH_FAN = 0,
	PWM_CH_LED1,
	PWM_CH_LED2,
	PWM_CH_COUNT
};

/* Fan Channels */
enum fan_channel {
	FAN_CH_0 = 0,
	/* Number of FAN channels */
	FAN_CH_COUNT,
};

enum mft_channel {
	MFT_CH_0 = 0,
	/* Number of MFT channels */
	MFT_CH_COUNT,
};

/* Baseboard Interrupt handlers. */
void baseboard_bj_connect_interrupt(enum gpio_signal signal);
void baseboard_en_pwr_pcore_s0(enum gpio_signal signal);
void baseboard_en_pwr_s0(enum gpio_signal signal);
void baseboard_usb_fault_alert(enum gpio_signal signal);
void bc12_interrupt(enum gpio_signal signal);
void ext_charger_interrupt(enum gpio_signal signal);
void dp_fault_interrupt(enum gpio_signal signal);
void hdmi_fault_interrupt(enum gpio_signal signal);
void ppc_interrupt(enum gpio_signal signal);
void sbu_fault_interrupt(enum ioex_signal signal);
void tcpc_alert_event(enum gpio_signal signal);

/* Required board functions */
void board_get_bj_power(int *voltage, int *current);

#endif /* !__ASSEMBLER__ */

#endif /* __CROS_EC_BASEBOARD_H */