1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
|
/* Copyright 2019 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Hatch board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Baseboard features */
#include "baseboard.h"
#define CONFIG_POWER_BUTTON
#define CONFIG_KEYBOARD_PROTOCOL_8042
#define CONFIG_LED_COMMON
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_HOSTCMD_ESPI
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096
/* Keyboard features */
#define CONFIG_PWM_KBLIGHT
/* Sensors */
/* LSM6DS3TR-C Base accel/gyro */
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_LSM6DSM
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* LIS2DWL Lid accel */
#define CONFIG_ACCEL_LIS2DWL
#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL))
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_LID_ANGLE_UPDATE
/* USB Type C and USB PD defines */
#define CONFIG_USB_PD_COMM_LOCKED
#define CONFIG_USB_PD_TCPM_ANX7447
#define CONFIG_USB_PD_TCPM_ANX7447_AUX_PU_PD
#define CONFIG_USB_PD_TCPM_PS8751
#define BOARD_TCPC_C0_RESET_HOLD_DELAY ANX74XX_RESET_HOLD_MS
#define BOARD_TCPC_C0_RESET_POST_DELAY ANX74XX_RESET_HOLD_MS
#define BOARD_TCPC_C1_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
#define BOARD_TCPC_C1_RESET_POST_DELAY 0
#define GPIO_USB_C1_TCPC_RST GPIO_USB_C1_TCPC_RST_ODL
/* USB Type A Features */
#define CONFIG_USB_PORT_POWER_SMART
#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT
#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
#define GPIO_USB1_ILIM_SEL GPIO_EN_USB_A_LOW_PWR_OD
/* BC 1.2 */
#define CONFIG_BC12_DETECT_PI3USB9201
/* Charger features */
/*
* The IDCHG current limit is set in 512 mA steps. The value set here is
* somewhat specific to the battery pack being currently used. The limit here
* was set based on the battery's discharge current limit and what was tested to
* prevent the AP rebooting with low charge level batteries.
*
* TODO(b/133447140): Revisit this threshold once peak power consumption tuning
* for the AP is completed.
*/
#define CONFIG_CHARGER_BQ25710_IDCHG_LIMIT_MA 8192
/* TI gauge IC 500ms WDT timeout setting under battery sleep mode
* induced battery cut-off, under the following conditions:
* 1. SMBus communication on FC is once per minute which allows
* battery entering sleep mode;
* 2. System load < 10mA and accumulate 5 hours will trigger battery
* simulation and result in a 500ms WDT timeout. So change charge
* max sleep time from once/minute to once/10 seconds to prevent
* battery entering sleep mode. See b/133375756 and b/148822924.
*/
#define CHARGE_MAX_SLEEP_USEC (10 * SECOND)
/* Volume Button feature */
#define CONFIG_VOLUME_BUTTONS
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
/* Fan features */
#define CONFIG_FANS 1
#undef CONFIG_FAN_INIT_SPEED
#define CONFIG_FAN_INIT_SPEED 50
#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_A_RAILS
#define CONFIG_THERMISTOR
#define CONFIG_THROTTLE_AP
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
#define CONFIG_TEMP_SENSOR_G753
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_L
#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L
#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum adc_channel {
ADC_TEMP_SENSOR_1, /* ADC0 */
ADC_TEMP_SENSOR_2, /* ADC1 */
ADC_CH_COUNT
};
enum sensor_id {
LID_ACCEL = 0,
BASE_ACCEL,
BASE_GYRO,
SENSOR_COUNT,
};
enum pwm_channel {
PWM_CH_KBLIGHT,
PWM_CH_FAN,
PWM_CH_COUNT
};
enum fan_channel {
FAN_CH_0 = 0,
/* Number of FAN channels */
FAN_CH_COUNT,
};
enum mft_channel {
MFT_CH_0 = 0,
/* Number of MFT channels */
MFT_CH_COUNT,
};
enum temp_sensor_id {
TEMP_SENSOR_1,
TEMP_SENSOR_2,
TEMP_SENSOR_3,
TEMP_SENSOR_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_LGC,
BATTERY_SUNWODA,
BATTERY_SMP,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
