1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Asurada board configuration */
#include "adc.h"
#include "adc_chip.h"
#include "button.h"
#include "charger.h"
#include "chipset.h"
#include "common.h"
#include "console.h"
#include "chip/it83xx/intc.h"
#include "driver/charger/isl923x.h"
#include "extpower.h"
#include "gpio.h"
#include "hooks.h"
#include "i2c.h"
#include "keyboard_scan.h"
#include "lid_switch.h"
#include "power.h"
#include "power_button.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "switch.h"
#include "tablet_mode.h"
#include "timer.h"
#include "uart.h"
#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args)
#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args)
static void x_ec_interrupt(enum gpio_signal signal);
#include "gpio_list.h"
const struct charger_config_t chg_chips[] = {
{
.i2c_port = I2C_PORT_CHARGER,
.i2c_addr_flags = ISL923X_ADDR_FLAGS,
.drv = &isl923x_drv,
},
};
const unsigned int chg_cnt = ARRAY_SIZE(chg_chips);
/*
* PWM channels. Must be in the exactly same order as in enum pwm_channel.
* There total three 16 bits clock prescaler registers for all pwm channels,
* so use the same frequency and prescaler register setting is required if
* number of pwm channel greater than three.
*/
const struct pwm_t pwm_channels[] = {
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
/* Wake-up pins for hibernate */
const enum gpio_signal hibernate_wake_pins[] = {
GPIO_AC_PRESENT,
GPIO_LID_OPEN,
GPIO_POWER_BUTTON_L,
};
const int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins);
/* power signal list. Must match order of enum power_signal. */
const struct power_signal_info power_signal_list[] = {
{GPIO_PMIC_EC_PWRGD, POWER_SIGNAL_ACTIVE_HIGH, "PMIC_PWR_GOOD"},
{GPIO_AP_IN_SLEEP_L, POWER_SIGNAL_ACTIVE_LOW, "AP_IN_S3_L"},
{GPIO_AP_EC_WATCHDOG_L,
POWER_SIGNAL_ACTIVE_LOW | POWER_SIGNAL_DISABLE_AT_BOOT,
"AP_WDT_ASSERTED"},
};
BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT);
/* Detect subboard */
static enum board_sub_board board_get_sub_board(void);
/* Initialize board. */
static void board_init(void)
{
}
DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
/* ADC channels. Must be in the exactly same order as in enum adc_channel. */
const struct adc_t adc_channels[] = {
/* Convert to mV (3000mV/1024). */
{"TEMP_SENSOR_SUBPMIC", 3000, 1024, 0, CHIP_ADC_CH0},
{"BOARD_ID_0", 3000, 1024, 0, CHIP_ADC_CH1},
{"BOARD_ID_1", 3000, 1024, 0, CHIP_ADC_CH2},
{"TEMP_SENSOR_AMB", 3000, 1024, 0, CHIP_ADC_CH3},
{"TEMP_SENSOR_CHARGER", 3000, 1024, 0, CHIP_ADC_CH5},
{"CHARGER_PMON", 3000, 1024, 0, CHIP_ADC_CH6},
{"TEMP_SENSOR_AP", 3000, 1024, 0, CHIP_ADC_CH7},
};
BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
/* Keyboard scan setting */
struct keyboard_scan_config keyscan_config = {
.output_settle_us = 35,
.debounce_down_us = 5 * MSEC,
.debounce_up_us = 40 * MSEC,
.scan_period_us = 3 * MSEC,
.min_post_scan_delay_us = 1000,
.poll_timeout_us = 100 * MSEC,
.actual_key_mask = {
0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */
},
};
/*
* I2C channels (A, B, and C) are using the same timing registers (00h~07h)
* at default.
* In order to set frequency independently for each channels,
* We use timing registers 09h~0Bh, and the supported frequency will be:
* 50KHz, 100KHz, 400KHz, or 1MHz.
* I2C channels (D, E and F) can be set different frequency on different ports.
* The I2C(D/E/F) frequency depend on the frequency of SMBus Module and
* the individual prescale register.
* The frequency of SMBus module is 24MHz on default.
* The allowed range of I2C(D/E/F) frequency is as following setting.
* SMBus Module Freq = PLL_CLOCK / ((IT83XX_ECPM_SCDCR2 & 0x0F) + 1)
* (SMBus Module Freq / 510) <= I2C Freq <= (SMBus Module Freq / 8)
* Channel D has multi-function and can be used as UART interface.
* Channel F is reserved for EC debug.
*/
/* I2C ports */
const struct i2c_port_t i2c_ports[] = {
{"bat_chg", IT83XX_I2C_CH_A, 100, GPIO_I2C_A_SCL, GPIO_I2C_A_SDA},
{"sensor", IT83XX_I2C_CH_B, 100, GPIO_I2C_B_SCL, GPIO_I2C_B_SDA},
{"usb0", IT83XX_I2C_CH_C, 100, GPIO_I2C_C_SCL, GPIO_I2C_C_SDA},
{"usb1", IT83XX_I2C_CH_E, 100, GPIO_I2C_E_SCL, GPIO_I2C_E_SDA},
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
static void x_ec_interrupt(enum gpio_signal signal)
{
/* TODO: implement this */
}
int board_get_version(void)
{
return 0;
}
/* Sub-board */
static enum board_sub_board board_get_sub_board(void)
{
static enum board_sub_board sub = SUB_BOARD_NONE;
if (sub != SUB_BOARD_NONE)
return sub;
/* HDMI board has external pull high. */
if (gpio_get_level(GPIO_EC_X_GPIO3))
sub = SUB_BOARD_HDMI;
else
sub = SUB_BOARD_TYPEC;
CPRINTS("Detect %s SUB", sub == SUB_BOARD_HDMI ? "HDMI" : "TYPEC");
return sub;
}
static void sub_board_init(void)
{
board_get_sub_board();
}
DECLARE_HOOK(HOOK_INIT, sub_board_init, HOOK_PRIO_INIT_I2C - 1);
|
