1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "charge_manager.h"
#include "console.h"
#include "gpio.h"
#include "pi3usb9281.h"
#include "system.h"
#include "usb_mux.h"
#include "usbc_ppc.h"
#include "util.h"
#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args)
#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args)
int pd_check_vconn_swap(int port)
{
/* TODO(waihong): Check any case we do not allow. */
return 1;
}
__override void pd_execute_data_swap(int port,
enum pd_data_role data_role)
{
int enable = (data_role == PD_ROLE_UFP);
int type;
/*
* Exclude the PD charger, in which the "USB Communications Capable"
* bit is unset in the Fixed Supply PDO.
*/
if (pd_capable(port))
enable = enable && pd_get_partner_usb_comm_capable(port);
/*
* The hub behind the BC1.2 chip may advertise a BC1.2 type. So
* disconnect the switch when getting the charger type to ensure
* the detected type is from external.
*/
usb_charger_set_switches(port, USB_SWITCH_DISCONNECT);
type = pi3usb9281_get_device_type(port);
usb_charger_set_switches(port, USB_SWITCH_RESTORE);
/* Exclude the BC1.2 charger, which is not detected as CDP or SDP. */
enable = enable && (type & (PI3USB9281_TYPE_CDP | PI3USB9281_TYPE_SDP));
/* Only mux one port to AP. If already muxed, return. */
if (enable && (!gpio_get_level(GPIO_USB_C0_HS_MUX_SEL) ||
gpio_get_level(GPIO_USB_C1_HS_MUX_SEL)))
return;
/* Port-0 and port-1 have different polarities. */
if (port == 0)
gpio_set_level(GPIO_USB_C0_HS_MUX_SEL, enable ? 0 : 1);
else if (port == 1)
gpio_set_level(GPIO_USB_C1_HS_MUX_SEL, enable ? 1 : 0);
}
static uint8_t vbus_en[CONFIG_USB_PD_PORT_MAX_COUNT];
static uint8_t vbus_rp[CONFIG_USB_PD_PORT_MAX_COUNT] = {TYPEC_RP_1A5,
TYPEC_RP_1A5};
static void board_vbus_update_source_current(int port)
{
if (port == 0) {
/*
* Port 0 is controlled by a USB-C PPC SN5S330.
*/
ppc_set_vbus_source_current_limit(port, vbus_rp[port]);
ppc_vbus_source_enable(port, vbus_en[port]);
} else if (port == 1) {
/*
* Port 1 is controlled by a USB-C current-limited power
* switch, NX5P3290. Change the GPIO driving the load switch.
*
* 1.5 vs 3.0 A limit is controlled by a dedicated gpio.
* If the GPIO is asserted, it shorts a n-MOSFET to put a
* 16.5k resistance (2x 33k in parallel) on the NX5P3290 load
* switch ILIM pin, setting a minimum OCP current of 3100 mA.
* If the GPIO is deasserted, the n-MOSFET is open that makes
* a single 33k resistor on ILIM, setting a minimum OCP
* current of 1505 mA.
*/
gpio_set_level(GPIO_EN_USB_C1_3A,
vbus_rp[port] == TYPEC_RP_3A0 ? 1 : 0);
gpio_set_level(GPIO_EN_USB_C1_5V_OUT, vbus_en[port]);
}
}
void pd_power_supply_reset(int port)
{
int prev_en;
prev_en = vbus_en[port];
/* Disable VBUS */
vbus_en[port] = 0;
board_vbus_update_source_current(port);
/* Enable discharge if we were previously sourcing 5V */
if (prev_en)
pd_set_vbus_discharge(port, 1);
#ifdef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
/* Give back the current quota we are no longer using */
charge_manager_source_port(port, 0);
#endif /* defined(CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT) */
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
}
int pd_set_power_supply_ready(int port)
{
/* Disable charging */
board_vbus_sink_enable(port, 0);
pd_set_vbus_discharge(port, 0);
/* Provide VBUS */
vbus_en[port] = 1;
board_vbus_update_source_current(port);
/* Ensure we advertise the proper available current quota */
charge_manager_source_port(port, 1);
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
return EC_SUCCESS; /* we are ready */
}
int board_vbus_source_enabled(int port)
{
return vbus_en[port];
}
__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp)
{
vbus_rp[port] = rp;
board_vbus_update_source_current(port);
}
int pd_snk_is_vbus_provided(int port)
{
return !gpio_get_level(port ? GPIO_USB_C1_VBUS_DET_L :
GPIO_USB_C0_VBUS_DET_L);
}
/* ----------------- Vendor Defined Messages ------------------ */
/**
* Is the port fine to be muxed its DisplayPort lines?
*
* Only one port can be muxed to DisplayPort at a time.
*
* @param port Port number of TCPC.
* @return 1 is fine; 0 is bad as other port is already muxed;
*/
static int is_dp_muxable(int port)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++)
if (i != port) {
if (usb_mux_get(i) & USB_PD_MUX_DP_ENABLED)
return 0;
}
return 1;
}
extern uint32_t dp_status[CONFIG_USB_PD_PORT_MAX_COUNT];
__override int svdm_dp_attention(int port, uint32_t *payload)
{
int lvl = PD_VDO_DPSTS_HPD_LVL(payload[1]);
int irq = PD_VDO_DPSTS_HPD_IRQ(payload[1]);
int mf_pref = PD_VDO_DPSTS_MF_PREF(payload[1]);
dp_status[port] = payload[1];
usb_mux_hpd_update(port, lvl, irq);
if (lvl && is_dp_muxable(port)) {
/*
* The GPIO USBC_MUX_CONF1 enables the mux of the DP redriver
* for the port 1.
*/
gpio_set_level(GPIO_USBC_MUX_CONF1, port == 1);
usb_mux_set(port, mf_pref ?
USB_PD_MUX_DOCK : USB_PD_MUX_DP_ENABLED,
USB_SWITCH_CONNECT, pd_get_polarity(port));
} else {
usb_mux_set(port, mf_pref ?
USB_PD_MUX_USB_ENABLED : USB_PD_MUX_NONE,
USB_SWITCH_CONNECT, pd_get_polarity(port));
}
/* ack */
return 1;
}
|