1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
/* -*- mode:c -*-
* Copyright (c) 2016 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Declare symbolic names for all the GPIOs that we care about.
* Note: Those with interrupt handlers must be declared first. */
/* Pull this low to interrupt the AP */
GPIO(INT_AP_L, PIN(0, 0), GPIO_INPUT)
/* Use these to take over the AP & EC flash (only when AP & EC are off!) */
GPIO(EC_FLASH_SELECT, PIN(0, 1), GPIO_INPUT)
GPIO(AP_FLASH_SELECT, PIN(0, 2), GPIO_INPUT)
/* As an input this mirrors EC_WP_L (which is controlled by RBOX, not a GPIO).
* As an output it can override EC_WP_L, although why would we? */
GPIO(AP_WP_L, PIN(0, 3), GPIO_INPUT)
/* Drive high to reset the EC & AP */
GPIO(SYS_RST, PIN(0, 4), GPIO_INPUT)
/* Indicate to EC when CCD is enabled */
GPIO(CCD_MODE, PIN(0, 5), GPIO_INPUT)
/* Battery has a 10K pulldown on its side. We provide the pullup. */
GPIO(BATT_PRES, PIN(0, 6), GPIO_INPUT)
/* Unimplemented signals which we need to emulate for now */
/* TODO(wfrichar): Half the boards don't use this signal. Take it out. */
UNIMPLEMENTED(ENTERING_RW)
/*
* If we are included by generic GPIO code that doesn't know about the PINMUX
* macro we need to provide an empty definition so that the invocations don't
* interfere with other GPIO processing.
*/
#ifndef PINMUX
#define PINMUX(...)
#endif
/* GPIOs - mark outputs as inputs too, to read back from the driven pad */
PINMUX(GPIO(INT_AP_L), B7, DIO_INPUT) /* DIOB7 is p_digitial_od */
/* We can't pull it up */
PINMUX(GPIO(EC_FLASH_SELECT), A3, DIO_INPUT)
PINMUX(GPIO(AP_FLASH_SELECT), A7, DIO_INPUT)
PINMUX(GPIO(AP_WP_L), A5, 0)
PINMUX(GPIO(SYS_RST), M0, DIO_INPUT)
PINMUX(GPIO(CCD_MODE), M1, DIO_INPUT)
PINMUX(GPIO(BATT_PRES), M2, 0)
/* UARTs */
PINMUX(FUNC(UART0_TX), A0, DIO_OUTPUT) /* Cr50 console */
PINMUX(FUNC(UART0_RX), A1, DIO_INPUT)
PINMUX(FUNC(UART1_TX), B3, DIO_INPUT) /* AP console */
PINMUX(FUNC(UART1_RX), B2, DIO_INPUT)
PINMUX(FUNC(UART2_TX), B5, DIO_INPUT) /* EC console */
PINMUX(FUNC(UART2_RX), B6, DIO_INPUT)
/* I2C pins are bi-directional */
PINMUX(FUNC(I2C0_SCL), B0, DIO_INPUT)
PINMUX(FUNC(I2C0_SDA), B1, DIO_INPUT)
/* Both SPI master and slave buses are wired directly to specific pads
*
* If CONFIG_SPS is defined, these pads are used:
* DIOA2 = SPS_MOSI (input)
* DIOA6 = SPS_CLK (input)
* DIOA10 = SPS_MISO (output)
* DIOA12 = SPS_CS_L (input)
* The digital inputs are enabled in sps.c
*
* If CONFIG_SPI_MASTER is defined, these pads are used:
* DIOA4 = SPI_MOSI (output)
* DIOA8 = SPI_CLK (output)
* DIOA11 = SPI_MISO (input)
* DIOA14 = SPI_CS_L (output)
* Note: Double-check to be sure these are configured in spi_master.c
*/
#undef PINMUX
|