1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
|
/* Copyright (c) 2012 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Daisy board-specific configuration */
#include "board.h"
#include "common.h"
#include "dma.h"
#include "i2c.h"
#include "gpio.h"
#include "pmu_tpschrome.h"
#include "registers.h"
#include "spi.h"
#include "task.h"
#include "util.h"
/*
* Daisy keyboard summary:
* 1. KEYSCAN task woken up via GPIO external interrupt when a key is pressed.
* 2. The task scans the keyboard matrix for changes. If key state has
* changed, the board-specific kb_send() function is called.
* 3. For Daisy, the EC is connected via I2C and acts as a slave, so the AP
* must initiate all transactions. EC_INT is driven low to interrupt AP when
* new data becomes available.
* 4. When the AP is interrupted, it initiates two i2c transactions:
* 1. 1-byte write: AP writes 0x01 to make EC send keyboard state.
* 2. 14-byte read: AP reads 1 keyboard packet (13 byte keyboard state +
* 1-byte checksum).
*/
#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP | GPIO_INT_BOTH)
#define GPIO_KB_OUTPUT (GPIO_OUTPUT | GPIO_PULL_UP | GPIO_OPEN_DRAIN)
/* GPIO interrupt handlers prototypes */
#ifndef CONFIG_TASK_GAIAPOWER
#define gaia_power_event NULL
#define gaia_suspend_event NULL
#define gaia_lid_event NULL
#else
void gaia_power_event(enum gpio_signal signal);
void gaia_suspend_event(enum gpio_signal signal);
void gaia_lid_event(enum gpio_signal signal);
#endif
#ifndef CONFIG_TASK_KEYSCAN
#define matrix_interrupt NULL
#endif
/* GPIO signal list. Must match order from enum gpio_signal. */
const struct gpio_info gpio_list[GPIO_COUNT] = {
/* Inputs with interrupt handlers are first for efficiency */
{"KB_PWR_ON_L", GPIO_B, (1<<5), GPIO_INT_BOTH, gaia_power_event},
{"PP1800_LDO2", GPIO_A, (1<<1), GPIO_INT_BOTH, gaia_power_event},
{"XPSHOLD", GPIO_A, (1<<3), GPIO_INT_RISING, gaia_power_event},
{"CHARGER_INT", GPIO_C, (1<<4), GPIO_INT_RISING, NULL},
{"LID_OPEN", GPIO_C, (1<<13), GPIO_INT_RISING, gaia_lid_event},
{"SUSPEND_L", GPIO_A, (1<<7), GPIO_INT_BOTH, gaia_suspend_event},
{"KB_IN00", GPIO_C, (1<<8), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN01", GPIO_C, (1<<9), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN02", GPIO_C, (1<<10), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN03", GPIO_C, (1<<11), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN04", GPIO_C, (1<<12), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN05", GPIO_C, (1<<14), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN06", GPIO_C, (1<<15), GPIO_KB_INPUT, matrix_interrupt},
{"KB_IN07", GPIO_D, (1<<2), GPIO_KB_INPUT, matrix_interrupt},
/* Other inputs */
{"AC_PWRBTN_L", GPIO_A, (1<<0), GPIO_INT_BOTH, NULL},
{"SPI1_NSS", GPIO_A, (1<<4), GPIO_PULL_UP, NULL},
/*
* I2C pins should be configured as inputs until I2C module is
* initialized. This will avoid driving the lines unintentionally.
*/
{"I2C1_SCL", GPIO_B, (1<<6), GPIO_INPUT, NULL},
{"I2C1_SDA", GPIO_B, (1<<7), GPIO_INPUT, NULL},
{"I2C2_SCL", GPIO_B, (1<<10), GPIO_INPUT, NULL},
{"I2C2_SDA", GPIO_B, (1<<11), GPIO_INPUT, NULL},
/* Outputs */
{"AC_STATUS", GPIO_A, (1<<5), GPIO_OUT_HIGH, NULL},
{"SPI1_MISO", GPIO_A, (1<<6), GPIO_OUT_HIGH, NULL},
{"EN_PP1350", GPIO_A, (1<<2), GPIO_OUT_LOW, NULL},
{"EN_PP5000", GPIO_A, (1<<11), GPIO_OUT_LOW, NULL},
{"EN_PP3300", GPIO_A, (1<<8), GPIO_OUT_LOW, NULL},
{"PMIC_PWRON_L", GPIO_A, (1<<12), GPIO_OUT_HIGH, NULL},
{"ENTERING_RW", GPIO_H, (1<<0), GPIO_OUT_LOW, NULL},
{"CHARGER_EN", GPIO_B, (1<<2), GPIO_OUT_LOW, NULL},
{"POWER_LED_L", GPIO_B, (1<<3), GPIO_OUT_HIGH, NULL},
{"EC_INT", GPIO_B, (1<<9), GPIO_HI_Z, NULL},
{"CODEC_INT", GPIO_H, (1<<1), GPIO_HI_Z, NULL},
{"KB_OUT00", GPIO_B, (1<<0), GPIO_KB_OUTPUT, NULL},
{"KB_OUT01", GPIO_B, (1<<8), GPIO_KB_OUTPUT, NULL},
{"KB_OUT02", GPIO_B, (1<<12), GPIO_KB_OUTPUT, NULL},
{"KB_OUT03", GPIO_B, (1<<13), GPIO_KB_OUTPUT, NULL},
{"KB_OUT04", GPIO_B, (1<<14), GPIO_KB_OUTPUT, NULL},
{"KB_OUT05", GPIO_B, (1<<15), GPIO_KB_OUTPUT, NULL},
{"KB_OUT06", GPIO_C, (1<<0), GPIO_KB_OUTPUT, NULL},
{"KB_OUT07", GPIO_C, (1<<1), GPIO_KB_OUTPUT, NULL},
{"KB_OUT08", GPIO_C, (1<<2), GPIO_KB_OUTPUT, NULL},
{"KB_OUT09", GPIO_B, (1<<1), GPIO_KB_OUTPUT, NULL},
{"KB_OUT10", GPIO_C, (1<<5), GPIO_KB_OUTPUT, NULL},
{"KB_OUT11", GPIO_C, (1<<6), GPIO_KB_OUTPUT, NULL},
{"KB_OUT12", GPIO_C, (1<<7), GPIO_KB_OUTPUT, NULL},
};
/* Auto detect I2C host port
* Daisy board has two I2C ports, I2C1(0) and I2C2(1), that can be configured
* as host. PMU chip is connected directly to the EC, and hence can be used
* for port detection
*/
#ifdef CONFIG_I2C_HOST_AUTO
static int i2c_host_port = -1;
/* Detect if tps65090 pmu is present on a i2c bus.
* This hack makes one single ec binary to work on boards with different
* stuffing options.
*
* TODO: Revert i2c host port detection after all dev boards been reworked or
* deprecated. Issue: http://crosbug.com/p/10622
*/
static int tps65090_is_present(int bus)
{
const int tps65090_addr = 0x90;
const int charger_ctrl_offset0 = 4;
int rv, reg;
rv = i2c_read8(bus, tps65090_addr, charger_ctrl_offset0, ®);
if (rv == EC_SUCCESS)
return 1;
return 0;
}
int board_i2c_host_port(void)
{
/* Default I2C host configuration is I2C1(0).
* If PMU doesn't ack on I2C2(1), set the host port to 0.
*/
if (i2c_host_port == -1)
i2c_host_port = tps65090_is_present(1) ? 1 : 0;
return i2c_host_port;
}
#endif /* CONFIG_I2C_HOST_AUTO */
void configure_board(void)
{
dma_init();
/* Enable all GPIOs clocks
* TODO: more fine-grained enabling for power saving
*/
STM32_RCC_AHBENR |= 0x3f;
/* Required to configure external IRQ lines (SYSCFG_EXTICRn) */
/* FIXME: This seems to break USB download in U-Boot (?!?) */
STM32_RCC_APB2ENR |= 1 << 0;
/* Enable SPI */
STM32_RCC_APB2ENR |= (1<<12);
/*
* I2C SCL/SDA on PB10-11 and PB6-7, bi-directional, no pull-up/down,
* initialized as hi-Z until alt. function is set
*/
STM32_GPIO_PUPDR_OFF(GPIO_B) &= ~((3 << (11*2)) | (3 << (10*2)) |
(3 << (7*2)) | (3 << (6*2)));
STM32_GPIO_MODER_OFF(GPIO_B) &= ~((3 << (11*2)) | (3 << (10*2)) |
(3 << (7*2)) | (3 << (6*2)));
STM32_GPIO_MODER_OFF(GPIO_B) |= (1 << (11*2)) | (1 << (10*2)) |
(1 << (7*2)) | (1 << (6*2));
STM32_GPIO_OTYPER_OFF(GPIO_B) |= (1<<11) | (1<<10) | (1<<7) | (1<<6);
STM32_GPIO_BSRR_OFF(GPIO_B) |= (1<<11) | (1<<10) | (1<<7) | (1<<6);
gpio_set_alternate_function(GPIO_B, (1<<11) |
(1<<10) |
(1<<7) |
(1<<6), GPIO_ALT_I2C);
/* Select Alternate function for USART1 on pins PA9/PA10 */
gpio_set_alternate_function(GPIO_A, (1<<9) | (1<<10), GPIO_ALT_USART);
/* EC_INT is output, open-drain */
STM32_GPIO_OTYPER_OFF(GPIO_B) |= (1<<9);
STM32_GPIO_PUPDR_OFF(GPIO_B) &= ~(0x3 << (2*9));
STM32_GPIO_MODER_OFF(GPIO_B) &= ~(0x3 << (2*9));
STM32_GPIO_MODER_OFF(GPIO_B) |= 0x1 << (2*9);
/* put GPIO in Hi-Z state */
gpio_set_level(GPIO_EC_INT, 1);
}
void board_interrupt_host(int active)
{
/* interrupt host by using active low EC_INT signal */
gpio_set_level(GPIO_EC_INT, !active);
}
void board_keyboard_suppress_noise(void)
{
/* notify audio codec of keypress for noise suppression */
gpio_set_level(GPIO_CODEC_INT, 0);
gpio_set_level(GPIO_CODEC_INT, 1);
}
int board_get_ac(void)
{
/*
* Detect AC state using combined gpio pins
*
* On daisy and snow, there's no single gpio signal to detect AC.
* GPIO_AC_PWRBTN_L provides AC on and PWRBTN release.
* GPIO_KB_PWR_ON_L provides PWRBTN release.
*
* When AC plugged, both GPIOs will be high.
*
* One drawback of this detection is, when press-and-hold power
* button. AC state will be unknown. This function will fallback
* to PMU VACG.
*/
int ac_good = 1, battery_good;
if (gpio_get_level(GPIO_KB_PWR_ON_L))
return gpio_get_level(GPIO_AC_PWRBTN_L);
/* Check PMU VACG */
if (!in_interrupt_context())
pmu_get_power_source(&ac_good, &battery_good);
/*
* Charging task only interacts with AP in discharging state. So
* return 1 when AC status can not be detected by GPIO or VACG.
*/
return ac_good;
}
|