1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Fleex board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Select Baseboard features */
#define VARIANT_OCTOPUS_EC_NPCX796FB
#define VARIANT_OCTOPUS_CHARGER_ISL9238
#include "baseboard.h"
/* EC console commands */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
#define CONFIG_LED_COMMON
#define CONFIG_LED_ONOFF_STATES_BAT_LOW 10
/*
* Some fuel gagues will return 1% immediately, without the battery being
* charged to the point of being able to withstand Vbus loss, so re-set
* allowable Try.SRC level and reset level to 2%
*/
#undef CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC
#define CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC 2
#define CONFIG_USB_PD_RESET_MIN_BATT_SOC 2
/* Sensors */
#define CONFIG_ACCEL_LIS2DE /* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
/* Volume button */
#define CONFIG_VOLUME_BUTTONS
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_13K7_47K_4050B
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
/* TI gauge IC 500ms WDT timeout setting under battery sleep mode
* induced battery cut-off, under the following conditions:
* 1. SMBus communication on FC is once per minute which allows
* battery entering sleep mode;
* 2. System load < 10mA and accumulate 5 hours will trigger battery
* simulation and result in a 500ms WDT timeout. So change charge
* max sleep time from once/minute to once/10 seconds to prevent
* battery entering sleep mode. See b/133375756.
*/
#define CHARGE_MAX_SLEEP_USEC (10 * SECOND)
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* Additional PPC second source */
#define CONFIG_USBC_PPC_SYV682X
#define CONFIG_USBC_PPC_DEDICATED_INT
/* SYV682 isn't connected to CC, so TCPC must provide VCONN */
#define CONFIG_USBC_PPC_SYV682X_NO_CC
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum adc_channel {
ADC_TEMP_SENSOR_AMB, /* ADC0 */
ADC_TEMP_SENSOR_CHARGER, /* ADC1 */
ADC_VBUS_C0, /* ADC9 */
ADC_VBUS_C1, /* ADC4 */
ADC_CH_COUNT
};
enum temp_sensor_id {
TEMP_SENSOR_BATTERY,
TEMP_SENSOR_AMBIENT,
TEMP_SENSOR_CHARGER,
TEMP_SENSOR_COUNT
};
enum pwm_channel {
PWM_CH_KBLIGHT,
PWM_CH_COUNT
};
/* Motion sensors */
enum sensor_id {
LID_ACCEL,
BASE_ACCEL,
BASE_GYRO,
SENSOR_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_BYD,
BATTERY_BYD16,
BATTERY_LGC,
BATTERY_LGC3,
BATTERY_SIMPLO,
BATTERY_SIMPLO_ATL,
BATTERY_SIMPLO_COS,
BATTERY_SIMPLO_LS,
BATTERY_SWD_ATL,
BATTERY_SWD_COS,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
