1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Waddledee board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Select Baseboard features */
#define VARIANT_DEDEDE_EC_IT8320
#include "baseboard.h"
/* System unlocked in early development */
#define CONFIG_SYSTEM_UNLOCKED
#define CONFIG_CMD_CHARGER_DUMP
/* Battery */
#define CONFIG_BATTERY_FUEL_GAUGE
/* BC 1.2 */
#define CONFIG_BC12_DETECT_PI3USB9201
/* Charger */
#define CONFIG_CHARGER_RAA489000 /* C0 and C1: Charger */
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#undef CONFIG_CHARGER_SINGLE_CHIP
#define CONFIG_OCPC
#define CONFIG_OCPC_DEF_RBATT_MOHMS 22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr */
#define GPIO_USB_C1_INT_ODL GPIO_SUB_USB_C1_INT_ODL
/* LED */
#define CONFIG_LED_PWM
#define CONFIG_LED_PWM_COUNT 1
/* PWM */
#define CONFIG_PWM
/* Sensors */
#define CONFIG_ACCEL_KX022 /* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_ACCEL_INTERRUPTS
/* Enable sensor fifo, must also define the _SIZE and _THRES */
#define CONFIG_ACCEL_FIFO
/* Power of 2 - Too large of a fifo causes too much timestamp jitter */
#define CONFIG_ACCEL_FIFO_SIZE 256
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE
/* TCPC */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_TCPM_RAA489000
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_TCPC_LOW_POWER
#define CONFIG_USB_PD_5V_EN_CUSTOM
/* Thermistors */
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_PP3300_A
/* USB Mux and Retimer */
#define CONFIG_USB_MUX_IT5205 /* C1: ITE Mux */
#define I2C_PORT_USB_MUX I2C_PORT_USB_C0 /* Required for ITE Mux */
#define CONFIG_USBC_RETIMER_TUSB544 /* C1 Redriver: TUSB544 */
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum chg_id {
CHARGER_PRIMARY,
CHARGER_SECONDARY,
CHARGER_NUM,
};
enum pwm_channel {
PWM_CH_KBLIGHT,
PWM_CH_LED_RED,
PWM_CH_LED_GREEN,
PWM_CH_LED_BLUE,
PWM_CH_COUNT,
};
/* Motion sensors */
enum sensor_id {
LID_ACCEL,
BASE_ACCEL,
BASE_GYRO,
SENSOR_COUNT
};
/* ADC channels */
enum adc_channel {
ADC_VSNS_PP3300_A, /* ADC0 */
ADC_TEMP_SENSOR_1, /* ADC2 */
ADC_TEMP_SENSOR_2, /* ADC3 */
ADC_SUB_ANALOG, /* ADC13 */
ADC_CH_COUNT
};
enum temp_sensor_id {
TEMP_SENSOR_1,
TEMP_SENSOR_2,
TEMP_SENSOR_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_C140254,
BATTERY_TYPE_COUNT,
};
int board_is_sourcing_vbus(int port);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|