blob: cfc5bbf0a07d1802d525309d562db4b32efa945d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Gingerbread board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Baseboard features */
#include "baseboard.h"
/* Optional features */
/*
* For MP release, CONFIG_SYSTEM_UNLOCKED must be undefined, and
* CONFIG_FLASH_PSTATE_LOCKED must be defined in order to enable write protect
* using option bytes WRP registers.
*/
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */
#undef CONFIG_FLASH_PSTATE_LOCKED
#define CONFIG_WP_ACTIVE_HIGH
/* Console */
#define CONFIG_UART_CONSOLE 3
#define CONFIG_UART_TX_DMA_CH STM32_DMAC_USART3_TX
#define CONFIG_UART_TX_DMA_PH DMAMUX_REQ_USART3_TX
/* USB Type C and USB PD defines */
#define USB_PD_PORT_HOST 0
#define USB_PD_PORT_DP 1
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_MUX_TUSB1064
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define BOARD_C1_NO_PPC
#define BOARD_C1_1A5_LIMIT
#define CONFIG_USB_PID 0x5049
#define CONFIG_USB_BCD_DEV 0x0001 /* v 0.01 */
#define CONFIG_USB_PD_IDENTITY_HW_VERS 1
#define CONFIG_USB_PD_IDENTITY_SW_VERS 1
/* I2C port names */
#define I2C_PORT_I2C1 0
#define I2C_PORT_I2C2 1
#define I2C_PORT_I2C3 2
/* Required symbolic I2C port names */
#define I2C_PORT_MP4245 I2C_PORT_I2C3
#define I2C_PORT_EEPROM I2C_PORT_I2C1
#define MP4245_I2C_ADDR_FLAGS MP4245_I2C_ADDR_0_FLAGS
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
#define GPIO_WP_L GPIO_EC_WP_L
#define GPIO_WP GPIO_EC_WP_L
/* Include math_util for bitmask_uint64 used in pd_timers */
#define CONFIG_MATH_UTIL
#ifndef __ASSEMBLER__
#include "registers.h"
#define GPIO_DP_HPD GPIO_DDI_MST_IN_HPD
#define GPIO_BPWR_DET GPIO_TP71
#define GPIO_PWR_BUTTON_RED GPIO_EC_STATUS_LED1
#define GPIO_PWR_BUTTON_GREEN GPIO_EC_STATUS_LED2
#define BUTTON_PRESSED_LEVEL 0
#define BUTTON_RELEASED_LEVEL 1
#define GPIO_TRIGGER_1 GPIO_USB3_A1_CDP_EN
#define GPIO_TRIGGER_2 GPIO_USB3_A2_CDP_EN
enum debug_gpio {
TRIGGER_1 = 0,
TRIGGER_2,
};
/*
* Function used to control GPIO signals as a timing marker. This is intended to
* be used for development/debugging purposes.
*
* @param trigger GPIO debug signal selection
* @param level desired level of the debug gpio signal
* @param pulse_usec pulse width if non-zero
*/
void board_debug_gpio(enum debug_gpio trigger, int level, int pulse_usec);
/*
* Function called in power on case to enable usbc related interrupts
*/
void board_enable_usbc_interrupts(void);
/*
* Function called in power off case to disable usbc related interrupts
*/
void board_disable_usbc_interrupts(void);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
