1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Hammer board configuration */
#include "common.h"
#include "ec_version.h"
#include "touchpad_elan.h"
#include "gpio.h"
#include "hooks.h"
#include "i2c.h"
#include "keyboard_raw.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "registers.h"
#include "task.h"
#include "timer.h"
#include "update_fw.h"
#include "usart-stm32f0.h"
#include "usart_tx_dma.h"
#include "usart_rx_dma.h"
#include "usb_descriptor.h"
#include "usb_i2c.h"
#include "util.h"
#include "gpio_list.h"
/******************************************************************************
* Define the strings used in our USB descriptors.
*/
const void *const usb_strings[] = {
[USB_STR_DESC] = usb_string_desc,
[USB_STR_VENDOR] = USB_STRING_DESC("Google Inc."),
[USB_STR_PRODUCT] = USB_STRING_DESC("Hammer"),
[USB_STR_SERIALNO] = 0,
[USB_STR_VERSION] = USB_STRING_DESC(CROS_EC_VERSION32),
[USB_STR_I2C_NAME] = USB_STRING_DESC("I2C"),
[USB_STR_UPDATE_NAME] = USB_STRING_DESC("Firmware update"),
};
BUILD_ASSERT(ARRAY_SIZE(usb_strings) == USB_STR_COUNT);
/******************************************************************************
* Support I2C bridging over USB, this requires usb_i2c_board_enable and
* usb_i2c_board_disable to be defined to enable and disable the I2C bridge.
*/
#ifdef SECTION_IS_RW
/* I2C ports */
const struct i2c_port_t i2c_ports[] = {
{"master", I2C_PORT_MASTER, 400,
GPIO_MASTER_I2C_SCL, GPIO_MASTER_I2C_SDA},
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
#ifdef BOARD_STAFF
#define KBLIGHT_PWM_FREQ 100 /* Hz */
#else
#define KBLIGHT_PWM_FREQ 10000 /* Hz */
#endif
/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */
const struct pwm_t pwm_channels[] = {
{STM32_TIM(TIM_KBLIGHT), STM32_TIM_CH(1), 0, KBLIGHT_PWM_FREQ},
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
int usb_i2c_board_enable(void) { return EC_SUCCESS; }
void usb_i2c_board_disable(void) {}
#endif
/******************************************************************************
* Initialize board.
*/
static void board_init(void)
{
}
DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
void board_config_pre_init(void)
{
/* enable SYSCFG clock */
STM32_RCC_APB2ENR |= 1 << 0;
/* Remap USART DMA to match the USART driver */
/*
* the DMA mapping is :
* Chan 4 : USART1_TX
* Chan 5 : USART1_RX
*/
STM32_SYSCFG_CFGR1 |= (1 << 9) | (1 << 10); /* Remap USART1 RX/TX DMA */
}
/*
* Side-band USB wake, to be able to wake lid even in deep S3, when USB
* controller is off.
*/
void board_usb_wake(void)
{
/*
* Poke detection pin for less than 100us, we disable interrupts
* to make sure that we do not get preempted (setting GPIO high
* for too long would prevent pulse detection on lid EC side from
* working properly, or even kill hammer power if it is held for
* longer than debounce time).
*/
interrupt_disable();
gpio_set_flags(GPIO_BASE_DET, GPIO_OUT_HIGH);
udelay(100);
gpio_set_flags(GPIO_BASE_DET, GPIO_INPUT);
interrupt_enable();
}
|
