1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/* Copyright 2020 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Lazor board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
#include "baseboard.h"
/* Internal SPI flash on NPCX7 */
#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) /* 512KB internal spi flash */
/* Reduce flash usage */
#define CONFIG_LTO
#define CONFIG_USB_PD_DEBUG_LEVEL 2
/* Switchcap */
#define CONFIG_LN9310
/* Keyboard */
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
#define CONFIG_PWM_KBLIGHT
/* Battery */
#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION"
#define CONFIG_BATTERY_REVIVE_DISCONNECT
#define CONFIG_BATTERY_FUEL_GAUGE
/* BC 1.2 Charger */
#define CONFIG_BC12_DETECT_PI3USB9201
/* USB */
#define CONFIG_USB_PD_TCPM_MULTI_PS8XXX
#define CONFIG_USB_PD_TCPM_PS8751
#define CONFIG_USB_PD_TCPM_PS8805
#define CONFIG_USB_PD_TCPM_PS8805_FORCE_DID
#define CONFIG_USBC_PPC_SN5S330
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
/* USB-A */
#define USB_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_DUMB
/* Sensors */
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
/* BMI160 Base accel/gyro */
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS
/* ICM426XX Base accel/gyro */
#define CONFIG_ACCELGYRO_ICM426XX
#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* KX022 lid accel */
#define CONFIG_ACCEL_KX022
/* BMA253 lid accel */
#define CONFIG_ACCEL_BMA255
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE
/* GPIO alias */
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_WP_L GPIO_EC_WP_ODL
#define GPIO_PMIC_RESIN_L GPIO_PM845_RESIN_L
#define GPIO_SWITCHCAP_PG_INT_L GPIO_DA9313_GPIO0
#define GPIO_SWITCHCAP_ON_L GPIO_SWITCHCAP_ON
/* Disable console commands to help save space */
#undef CONFIG_CMD_BATTFAKE
#undef CONFIG_CMD_CHARGE_SUPPLIER_INFO
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
#include "sku.h"
enum adc_channel { ADC_VBUS, ADC_AMON_BMON, ADC_PSYS, ADC_CH_COUNT };
/* Motion sensors */
enum sensor_id {
LID_ACCEL = 0,
BASE_ACCEL,
BASE_GYRO,
SENSOR_COUNT,
};
enum pwm_channel { PWM_CH_KBLIGHT = 0, PWM_CH_DISPLIGHT, PWM_CH_COUNT };
/* List of possible batteries */
enum battery_type {
BATTERY_AP16L5J,
BATTERY_AP16L5J_009,
BATTERY_AP16L8J,
BATTERY_LGC_AP18C8K,
BATTERY_MURATA_AP18C4K,
BATTERY_TYPE_COUNT,
};
/* support factory keyboard test */
#define CONFIG_KEYBOARD_FACTORY_TEST
/* Reset all TCPCs. */
void board_reset_pd_mcu(void);
void board_set_tcpc_power_mode(int port, int mode);
/* Motion sensor interrupt */
void motion_interrupt(enum gpio_signal signal);
#endif /* !defined(__ASSEMBLER__) */
#endif /* __CROS_EC_BOARD_H */
|
