1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Lazor board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
#include "baseboard.h"
/* Internal SPI flash on NPCX7 */
#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) /* 512KB internal spi flash */
/* Switchcap */
#define CONFIG_LN9310
/* Keyboard */
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
#define CONFIG_PWM_KBLIGHT
/* Battery */
#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION"
#define CONFIG_BATTERY_REVIVE_DISCONNECT
#define CONFIG_BATTERY_FUEL_GAUGE
/* BC 1.2 Charger */
#define CONFIG_BC12_DETECT_PI3USB9201
/* USB */
#define CONFIG_USB_PD_TCPM_MULTI_PS8XXX
#define CONFIG_USB_PD_TCPM_PS8751
#define CONFIG_USB_PD_TCPM_PS8805
#define CONFIG_USB_PD_TCPM_PS8805_FORCE_DID
#define CONFIG_USBC_PPC_SN5S330
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
/* USB-A */
#define USB_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_DUMB
/* Sensors */
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
/* BMI160 Base accel/gyro */
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS
/* ICM426XX Base accel/gyro */
#define CONFIG_ACCELGYRO_ICM426XX
#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* KX022 lid accel */
#define CONFIG_ACCEL_KX022
/* BMA253 lid accel */
#define CONFIG_ACCEL_BMA255
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
#define CONFIG_GMR_TABLET_MODE
#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L
/* GPIO alias */
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_WP_L GPIO_EC_WP_ODL
#define GPIO_PMIC_RESIN_L GPIO_PM845_RESIN_L
#define GPIO_SWITCHCAP_PG_INT_L GPIO_DA9313_GPIO0
#define GPIO_SWITCHCAP_ON_L GPIO_SWITCHCAP_ON
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
#include "sku.h"
enum adc_channel {
ADC_VBUS,
ADC_AMON_BMON,
ADC_PSYS,
ADC_CH_COUNT
};
/* Motion sensors */
enum sensor_id {
LID_ACCEL = 0,
BASE_ACCEL,
BASE_GYRO,
SENSOR_COUNT,
};
enum pwm_channel {
PWM_CH_KBLIGHT = 0,
PWM_CH_DISPLIGHT,
PWM_CH_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_AP16L5J,
BATTERY_AP16L5J_009,
BATTERY_AP16L8J,
BATTERY_LGC_AP18C8K,
BATTERY_MURATA_AP18C4K,
BATTERY_TYPE_COUNT,
};
/* support factory keyboard test */
#define CONFIG_KEYBOARD_FACTORY_TEST
/* Reset all TCPCs. */
void board_reset_pd_mcu(void);
void board_set_tcpc_power_mode(int port, int mode);
/* Motion sensor interrupt */
void motion_interrupt(enum gpio_signal signal);
#endif /* !defined(__ASSEMBLER__) */
#endif /* __CROS_EC_BOARD_H */
|
