1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
|
/* -*- mode:c -*-
*
* Copyright 2015 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Inputs with interrupt handlers are first for efficiency */
GPIO_INT(AC_PRESENT, A, 0, GPIO_INT_BOTH, extpower_interrupt) /* AC power present: PA 0 */
GPIO_INT(POWER_BUTTON_L, B, 5, GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt) /* Keyboard power button: PB 5 */
GPIO_INT(SOC_POWER_GOOD_L, A, 3, GPIO_INT_BOTH, power_signal_interrupt)
GPIO_INT(LID_OPEN, C, 13, GPIO_INT_BOTH, lid_interrupt) /* LID switch detection */
GPIO_INT(SUSPEND_L, C, 7, GPIO_INT_BOTH, power_signal_interrupt) /* AP suspend/resume state */
/* Keyboard inputs */
GPIO_INT(KB_IN00, C, 8, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN01, C, 9, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN02, C, 10, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN03, C, 11, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN04, C, 12, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN05, C, 14, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN06, C, 15, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
GPIO_INT(KB_IN07, D, 2, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt)
/* SPI Chip Select */
GPIO_INT(SPI1_NSS, A, 4, GPIO_INT_BOTH | GPIO_PULL_UP, spi_event)
GPIO(5V_GOOD_L, A, 1, GPIO_INT_BOTH)
GPIO(AP_RESET_H, B, 3, GPIO_OUT_LOW)
GPIO(BOARD_VERSION1, C, 6, GPIO_INPUT|GPIO_PULL_UP) /* Board version stuffing resistor 1 */
/* Outputs */
GPIO(BAT_LED0, B, 11, GPIO_OUT_LOW) /* LED_GREEN */
GPIO(BAT_LED1, A, 11, GPIO_OUT_LOW) /* LED_ORANGE */
GPIO(EC_BL_OVERRIDE, F, 1, GPIO_OUT_LOW)
GPIO(EC_INT, B, 9, GPIO_OUT_HIGH)
GPIO(ENTERING_RW, F, 0, GPIO_OUT_LOW)
GPIO(KB_OUT00, B, 0, GPIO_KB_OUTPUT)
GPIO(KB_OUT01, B, 8, GPIO_KB_OUTPUT)
GPIO(KB_OUT02, B, 12, GPIO_OUT_LOW) /* KSO2 is inverted */
GPIO(KB_OUT03, B, 13, GPIO_KB_OUTPUT)
GPIO(KB_OUT04, B, 14, GPIO_KB_OUTPUT)
GPIO(KB_OUT05, B, 15, GPIO_KB_OUTPUT)
GPIO(KB_OUT06, C, 0, GPIO_KB_OUTPUT)
GPIO(KB_OUT07, C, 1, GPIO_KB_OUTPUT)
GPIO(KB_OUT08, C, 2, GPIO_KB_OUTPUT)
GPIO(KB_OUT09, B, 1, GPIO_KB_OUTPUT)
GPIO(KB_OUT10, C, 5, GPIO_KB_OUTPUT)
GPIO(KB_OUT11, C, 4, GPIO_KB_OUTPUT)
GPIO(KB_OUT12, A, 14, GPIO_KB_OUTPUT)
GPIO(SYSTEM_POWER_H, B, 10, GPIO_OUT_LOW)
GPIO(PMIC_PWRON_H, A, 12, GPIO_OUT_LOW)
GPIO(PMIC_WARM_RESET_H, C, 3, GPIO_ODR_LOW)
/*
* I2C pins should be configured as inputs until I2C module is
* initialized. This will avoid driving the lines unintentionally.
*/
GPIO(MASTER_I2C_SCL, B, 6, GPIO_INPUT)
GPIO(MASTER_I2C_SDA, B, 7, GPIO_INPUT)
/* Unimplemented signals which we need to emulate for now */
/* UNIMPLEMENTED(ENTERING_RW) */
UNIMPLEMENTED(WP_L)
UNIMPLEMENTED(BOARD_VERSION2)
UNIMPLEMENTED(BOARD_VERSION3)
ALTERNATE(A, 0x0600, 1, MODULE_UART, 0) /* USART1: PA9/PA10 */
ALTERNATE(B, 0x00c0, 1, MODULE_I2C, 0) /* I2C MASTER:PB6/7 */
ALTERNATE(A, 0x00f0, 0, MODULE_SPI, 0) /* SPI SLAVE:PA4/5/6/7 */
|
