1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
/* Copyright 2015 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "adc.h"
#include "gpio.h"
#include "registers.h"
/* USB Power delivery board configuration */
#ifndef __CROS_EC_USB_PD_CONFIG_H
#define __CROS_EC_USB_PD_CONFIG_H
/* Timer selection for baseband PD communication */
#define TIM_CLOCK_PD_TX_C0 15
#define TIM_CLOCK_PD_RX_C0 1
#define TIM_CLOCK_PD_TX(p) TIM_CLOCK_PD_TX_C0
#define TIM_CLOCK_PD_RX(p) TIM_CLOCK_PD_RX_C0
/* Timer channel */
#define TIM_RX_CCR_C0 1
#define TIM_TX_CCR_C0 2
/* RX timer capture/compare register */
#define TIM_CCR_C0 (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_C0, TIM_RX_CCR_C0))
#define TIM_RX_CCR_REG(p) TIM_CCR_C0
/* TX and RX timer register */
#define TIM_REG_TX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_TX_C0))
#define TIM_REG_RX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_RX_C0))
#define TIM_REG_TX(p) TIM_REG_TX_C0
#define TIM_REG_RX(p) TIM_REG_RX_C0
/* use the hardware accelerator for CRC */
#define CONFIG_HW_CRC
/* TX uses SPI1 on PB3-4 */
#define SPI_REGS(p) STM32_SPI1_REGS
static inline void spi_enable_clock(int port)
{
STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI1;
}
/* DMA for transmit uses DMA_CH3 */
#define DMAC_SPI_TX(p) STM32_DMAC_CH3
/* RX uses COMP1 and COMP2 on TIM1 CH1 */
#define CMP1OUTSEL STM32_COMP_CMP1OUTSEL_TIM1_IC1
#define CMP2OUTSEL STM32_COMP_CMP2OUTSEL_TIM1_IC1
#define TIM_TX_CCR_IDX(p) TIM_TX_CCR_C0
#define TIM_RX_CCR_IDX(p) TIM_RX_CCR_C0
#define TIM_CCR_CS 1
#define EXTI_COMP_MASK(p) ((1 << 21) | (1 << 22))
#define IRQ_COMP STM32_IRQ_COMP
/* triggers packet detection on comparator falling edge */
#define EXTI_XTSR STM32_EXTI_FTSR
/* DMA for receive uses DMA_CH2 */
#define DMAC_TIM_RX(p) STM32_DMAC_CH2
/* the pins used for communication need to be hi-speed */
static inline void pd_set_pins_speed(int port)
{
/* 40 MHz pin speed on SPI PB3/4/15 */
STM32_GPIO_OSPEEDR(GPIO_B) |= 0xC00003C0;
/* 40 MHz pin speed on SPI PA6 */
STM32_GPIO_OSPEEDR(GPIO_A) |= 0x00003000;
}
/* Reset SPI peripheral used for TX */
static inline void pd_tx_spi_reset(int port)
{
/* Reset SPI1 */
STM32_RCC_APB2RSTR |= (1 << 12);
STM32_RCC_APB2RSTR &= ~(1 << 12);
}
/* Drive the CC line from the TX block */
static inline void pd_tx_enable(int port, int polarity)
{
/* put SPI function on TX pin */
if (polarity) {
/* USB_C0_CC2_TX_DATA: PA6 is SPI1 MISO */
gpio_set_alternate_function(GPIO_A, 0x0040, 0);
/* MCU ADC PA3 pin output low */
STM32_GPIO_MODER(GPIO_A) = (STM32_GPIO_MODER(GPIO_A)
& ~(3 << (2*3))) /* PA3 disable ADC */
| (1 << (2*3)); /* Set as GPO */
gpio_set_level(GPIO_USB_C0_CC2_PD, 0);
} else {
/* USB_C0_CC1_TX_DATA: PB4 is SPI1 MISO */
gpio_set_alternate_function(GPIO_B, 0x0010, 0);
/* MCU ADC PA1 pin output low */
STM32_GPIO_MODER(GPIO_A) = (STM32_GPIO_MODER(GPIO_A)
& ~(3 << (2*1))) /* PA1 disable ADC */
| (1 << (2*1)); /* Set as GPO */
gpio_set_level(GPIO_USB_C0_CC1_PD, 0);
}
}
/* Put the TX driver in Hi-Z state */
static inline void pd_tx_disable(int port, int polarity)
{
if (polarity) {
/* Set TX_DATA to Hi-Z, PA6 is SPI1 MISO */
STM32_GPIO_MODER(GPIO_A) = (STM32_GPIO_MODER(GPIO_A)
& ~(3 << (2*6)));
/* set ADC PA3 pin to ADC function (Hi-Z) */
STM32_GPIO_MODER(GPIO_A) = (STM32_GPIO_MODER(GPIO_A)
| (3 << (2*3))); /* PA3 as ADC */
} else {
/* Set TX_DATA to Hi-Z, PB4 is SPI1 MISO */
STM32_GPIO_MODER(GPIO_B) = (STM32_GPIO_MODER(GPIO_B)
& ~(3 << (2*4)));
/* set ADC PA1 pin to ADC function (Hi-Z) */
STM32_GPIO_MODER(GPIO_A) = (STM32_GPIO_MODER(GPIO_A)
| (3 << (2*1))); /* PA1 as ADC */
}
}
/* we know the plug polarity, do the right configuration */
static inline void pd_select_polarity(int port, int polarity)
{
/*
* use the right comparator : CC1 -> PA1 (COMP1 INP)
* CC2 -> PA3 (COMP2 INP)
* use VrefInt / 2 as INM (about 600mV)
*/
STM32_COMP_CSR = (STM32_COMP_CSR
& ~(STM32_COMP_CMP1INSEL_MASK | STM32_COMP_CMP2INSEL_MASK
| STM32_COMP_CMP1EN | STM32_COMP_CMP2EN))
| STM32_COMP_CMP1INSEL_VREF12 | STM32_COMP_CMP2INSEL_VREF12
| (polarity ? STM32_COMP_CMP2EN : STM32_COMP_CMP1EN);
}
/* Initialize pins used for TX and put them in Hi-Z */
static inline void pd_tx_init(void)
{
gpio_config_module(MODULE_USB_PD, 1);
}
static inline void pd_set_host_mode(int port, int enable)
{
/* We're always a pull-down, nothing to do here */
}
static inline void pd_config_init(int port, uint8_t power_role)
{
/* Initialize TX pins and put them in Hi-Z */
pd_tx_init();
}
static inline int pd_adc_read(int port, int cc)
{
return adc_read_channel(cc ? ADC_C0_CC2_PD : ADC_C0_CC1_PD);
}
#endif /* __CROS_EC_USB_PD_CONFIG_H */
|
